Jasco ZW3105 Plug-in Smart Dimmer

Product Overview

This document provides instructions for the Jasco ZW3105 Plug-in Smart Dimmer. It allows for remote and manual control of connected lighting, offering Z-Wave network integration for smart home automation.

Important: Do not return this product to the store. For assistance, contact Jasco Consumer Care.

For setup videos and more information, visit https://byjasco.com/55252i.

Available Jasco Products:

• In-Wall Smart Dimmers
• Plug-in Smart Dimmers
• In-Wall Add-on Switches
• In-Wall Motion Switch or Dimmer
• Plug-in Smart Switches
• In-Wall Smart Switches
• Enbrighten Smart LED Bulb
• In-Wall Smart Fan Control
• Hinge Pin Smart Door Sensor
• Direct Wire, 40A Outdoor Smart Switch
• Portable Smart Multi Sensor
• In-Wall Tamper-Resistant Smart Outlet
• Plug-in Outdoor Smart Switch

Safety Warnings

RISK OF FIRE

RISK OF ELECTRICAL SHOCK

RISK OF BURNS

To reduce the risk of electric shock, this product has a grounding type plug with a third pin. This plug will only fit into a grounding type power outlet. If the plug does not fit, contact a qualified electrician. Do not alter the plug.

Controlling Appliances:

Caution: To reduce the risk of overheating and damage to other equipment, do not install to control:

• Motor-operated appliances
• Fluorescent lighting fixtures
• Transformer-supplied appliances

Use only to control incandescent or dimmable CFL/LED bulbs.

Do not exceed electrical ratings.

Do not use to control devices where unintended operation could cause unsafe conditions (e.g., heat lamps, sun lamps).

Medical Equipment Warning: Z-Wave enabled devices should never be used to supply power to or control the ON/OFF status of medical life-support equipment.

Getting to Know Your Z-Wave Device

Maximum Load: 300W (2.5A) incandescent or 100W dimmable CFL/LED for the Z-Wave controlled outlet.

This device features:

• One Z-Wave controlled AC outlet for standard incandescent lighting or dimmable CFL/LEDs.
• Remote ON/OFF and brightness control via a Z-Wave controller.
• Manual ON/OFF and brightness control using the top-mounted push button.
• One always-on pass-through AC outlet.
• Space-efficient design that does not block the lower outlet of a duplex receptacle (when installed in the upper outlet with the ground pin down).
• Plugs and cords for connected devices route to the side, allowing close placement of furniture.
• Grounded 3-wire power connection for safety.
• Advanced features adjustable via a Z-Wave controller supporting the Z-Wave configuration command class. Visit www.ezzwave.com/config for a list of configurations.

Device Components:

• A. Z-Wave controlled outlet: This outlet allows remote ON/OFF and dimming of the connected lamp.
• B. Manual/program button:
  • Single press: Turn the lamp ON/OFF.
  • Press and hold: Dim/brighten the lamp.
  • Single press: Add or remove the device from a Z-Wave network.
• C. Pass-through AC outlet: This space-saving outlet is always on and not controlled by Z-Wave.
• D. Cycle LED light: The LED serves as a guide light or status indicator. To cycle through options, press the program button 10 times quickly:
  1. LED is ON when the load is ON (default).
  2. LED is ON when the load is OFF (guide light in the dark).
  3. LED is always OFF.
  4. LED is always ON.

Installation:

1. Plug the light you want to control into the Z-Wave controlled outlet on the smart dimmer.
2. Plug the smart dimmer directly into an available grounded outlet (the top outlet is recommended).

Note: Plug directly into the outlet. Do not use with extension cords.

Dimmable Bulbs: Actual performance of CFL or LED bulbs varies by manufacturer. Only use bulbs designed as dimmable. Check bulb packaging or contact the manufacturer. For a list of recommended bulbs, visit www.ezzwave.com.

Adding Your Device to a Z-Wave Network

Inclusion Process:

1. Follow the instructions provided by your Z-Wave certified controller to add a device to the network.
2. When the controller is ready to add your device, press the manual/program button on the smart dimmer.

Once included, you can control your fixture's ON/OFF status and brightness through groups, scenes, schedules, and automations programmed by your controller. Remote access via mobile devices may be available if your controller supports it.

S2 Security Code: If prompted by the controller, refer to the product label for the S2 security code (PIN). Enter the 5-digit PIN.

Note: Please reference your controller's manual for specific instructions.

SmartStart Inclusion: Products enabled with SmartStart can be added to a Z-Wave network by scanning the QR code on the product with a SmartStart-compatible controller. No further action is required; the product will be added automatically within 10 minutes of being powered on within the network vicinity.

Removing and Resetting the Device

To Remove from Network:

1. Follow your Z-Wave certified controller's instructions to remove a device.
2. When the controller is ready, press and release the manual/program button on the smart dimmer.

To Return to Factory Defaults:

1. Unplug the dimmer from the receptacle.
2. Press and hold the top button for at least three seconds while plugging the dimmer back into a receptacle.

Note: This reset procedure should only be used if your network's primary controller is missing or inoperable.

Z-Wave Interoperability

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from different manufacturers. Non-battery operated nodes within the network will act as repeaters, regardless of vendor, to increase network reliability.

Association Command Class

This device supports the Association Command Class with three groups:

• Association Group 1: Supports Lifeline and Multi Level Report.
• Association Group 2: Supports Basic Set and is controlled with the local load.
• Association Group 3: Supports Basic Set and is controlled by double pressing the button.

Each Association Group supports a maximum of 5 nodes.

Specifications

Specifications are subject to change without notice due to continuing product improvement.

Warranty

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

For warranty service, please contact Jasco Consumer Care at 1-800-654-8483 (option 1) between 7 AM – 8 PM, Monday–Friday, Central Time, or visit www.byjasco.com.

FCC/IC Compliance

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications. Such modifications could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If interference occurs, users are encouraged to try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to an outlet on a different circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician.

Important Note: To comply with FCC RF exposure requirements, no changes to the antenna or device are permitted. Any such change could result in the device exceeding RF exposure requirements and voiding the user's authority to operate it.

Responsible Party (US Contact): Jasco Products Company, 10 E. Memorial Rd., Oklahoma City, OK 73114. FCC ID: U2ZZW3105, IC: 6924A-ZW3105.