ZUSKE USER MANUAL

SOLAR POWERED LED STRING LIGHT

Introduction

Product: 31FT G40 LED SOLAR STRING LIGHT

Note: Please read this user manual carefully before use and installation.

Diagram Description: The illustration shows a solar panel connected to a string of lights. Key components are labeled:

1. Solar panel: A panel designed to capture sunlight.
2. Control box: The central unit housing the battery and electronics.
3. Brace: A support structure.
4. Ground spike: For mounting the solar panel in the ground.
5. Indicators: Lights showing status.
6. USB Type-C Port: For alternative charging.
7. Switch: For turning the lights on/off and changing modes.
8. LED string lights: The decorative lights themselves.

Package Contains

1 * Control box (with solar panel)
1 * Ground spike
1 * 31FT String light (15pcs bulbs and 15pcs filaments)
1 * Spare bulbs and filaments
3 * Anchors & screws
1 * User manual

Specifications

Solar panel	1.3W/5.5V
Li-ion battery	1200mAh/3.7v x 1pcs
Charge cycles	350
Bulb quantity	15Pcs+1Pcs Spare Bulb
Filaments quantity	15Pcs+1Pcs Spare Filaments
Length of string	31FT
Charging time	8 hours (Solar Panel) 4 hours (USB Charger 5V 1A)
Power Per Bulb	0.2W
Waterproof Level	IP65
Lighting mode	Steady Light, Slow Flash, Quick Flash, Pulsating Light, Breathing Light. 5 Modes Circulate.

Installation

Connect the ground spike and string lights with the control box.
Mount the solar panel and secure the control box to a location where the solar panel can receive direct sunlight. This can be done by attaching the ground spike to the control box and placing it on the ground, or by mounting it on a wall using screws. Ensure the solar panel is facing upwards.
Press the Switch button to select the light mode:
- Single Press: Steady Light
- Double Press: Slow Flash
- Triple Press: Quick Flash
- Quadruple Press: Pulsating Light
- Fifth Press: Breathing Light
- Sixth Press: Off

Advice

Please recharge the product before the first use via solar panel or a 5V USB charger. Indicators will turn green when fully charged. (See Fig. 1)
A USB charger can be used to charge the product on rainy or cloudy days. (See Fig. 2)

Attentions

Please install the solar panel in a sunny place and ensure it is mounted firmly.
Please keep the solar panel facing up when installing.
Please classify the built-in lithium battery for disposal according to regulations.
IP65 is suitable for daily outdoor use, but not for harsh environments. It is strictly forbidden to soak the product. Damage from localized heating and pressurization is not allowed.

Troubleshooting

1. The light does not come on at all:

a) Make sure the wall switch and circuit breaker are on.

2. One of the lamps has burned out:

a) Disconnect power to the string light. Remove the affected lamp by gently gripping the lamp lens and turning it counter-clockwise. Gently pull out the LED filament piece, then replace it with the spare LED filament piece included. Push in until fully seated. Only use the spare part provided with this string. Replace the lamp lens by inserting it over the LED filament, then gently turn the lamp in a clockwise direction until fully seated.

b) If you replace the filament according to the steps above and it does not work normally after turning on the power, it may be that you inserted the filament in the wrong direction. Disconnect power to the string light. Remove the filament and rotate the filament 180° (change the direction of the wires 'a' and 'b' at the top of the filament), then insert it into the socket. Install the bulb and turn on the power to confirm whether it can work normally.

Tips: If you follow the steps above to replace the filament, but it still does not work after turning on the power, please feel free to contact us. We will do our best to help you solve the problem.

Quality Assurance

If you have any questions, please feel free to contact us.

E-mail: EsK-tech@hotmail.com

Importer name: EsK TECHNOLOGY INC

Importer address: 100 N HOWARD ST STER, SPOKANE, WA, 99201, USA

Certifications: CE, UKCA, FCC