Instruction Manual for PARAMITA models including: P5P7P9, 2A62Y-P5P7P9, 2A62YP5P7P9, Amita P5 ENC Wireless Earphone, Amita P5, ENC Wireless Earphone
Shenzhen xingming Technology Co.,ltd P5P7P9 Wireless Earphones 2A62Y-P5P7P9 2A62YP5P7P9 p5p7p9
Amita P5 真无线蓝牙耳机使用说明书 说明书下载
ENC Wireless Earphone
THE INSTRUCTIONS
Please carefully read this Manual before using this product for the very first time and well keep it for the further reference.
Precautions
Thank you for purchasing the Environmental Noise Cancelling True Wireless Bluetooth Headphones produced by our company. For listening experience, please wear and use the headset correctly, and do not disassemble the hardware by yourself.
Please read this manual carefully before use, thank you again for your support and love.
.Specification
Bluetooth Communication Scope
Waterproof Level Frequency Response
Sensitivity Impedance
Support Battery Capacity
Horn Chip Audio Coding Play Time Charging Case Charging Port Product Size(charging box) Product Weight
Packing List
V5.2 10m(no obstacle)
IPX4 20Hz-20KHz 110.6dB±3dB
32 HFP/HSP/A2DP/AVRCP
350mAh/30mAh 10mm Dynamic unit
Bluetrum 5626A SBC/AAC 4.5H Type-c Port
58.8*51.3*28.3mm About 39g
Headphone set, Silicone earbuds, Charging cable, Instruction manual
1
.Schematic Diagram
Touch sensing area Charging case indicator
2
Charging interface
ENC
ENC
1.
V5.2 10m
IPX4 20Hz-20KHz 110.6dB±3dB
32 HFP/HSP/A2DP/AVRCP
350mAh/30mAh 10mm 5626A
SBC/AAC 4.5H
Type-C 58.8*51.3*28.3mm
39g
2.
1
2
. Function Overview
Steps:
1. Power on: Open the charging case, take out the earbuds and turn it on. 2. Bluetooth Pairing: Turn on the "Bluetooth" of the device and take out the earbuds from
the charging case, search for " Amita P5 " click "connect". When using the headset again, open the charging case, take out the earbuds, and the earbuds will automatically connect to the device.
12:00 Settings
Bluetooth
Bluetooth
MY DEVICES Amita P5
Connected
Warm tips: If the pairing fails, put the earbuds into the charging case,and then try the steps above again, the earbuds will automatically shut down when there is no devices to connect in 5 minutes.
3
.Charging Operation
1. Charging Case Charging: Connect the charging cable into the charging pot on the charging case.
2. Earbuds Charging: Put the earbuds into the charging case, the earbuds will automatically shut down and charge.
Function Definition:
FUNCTION Pause/Start
OPERATION Tap the left or right earbud once
Previous Song
Tap the left earbud three times
Next Song
Tap the right earbud three times
Answer A Call
Long Press the left or right earbud for 2s
Reject A Call
Tap the left or right earbud twice
End A Call
Tap the left or right earbud twice
Game/Music Mode Wake up voice assistant
Tap the left earbud four times Long Press the left or right earbud
EQ Mode
Tap the right earbud four times
Volume +
Tap the right earbud twice
Volume Power ON Power OFF
Tap the left earbud twice Long Press the left and right earbud for 5S
Long Press the left or right earbud for 5S
Charging And Indicator Light Display:
Product Status
Charging case (Charging)
Electricity Status Fully Charged Charging
Indicator Light The light is always on
Light flashes
Discharging The Charging case
Normal Discharge State The light turns off after 4s
Low Light
The light flashes for 4s and then turns off
Put The Earbuds Back into the Charging case
/
The light flashes once
4
3.
: "" Amita P5
12:00
Amita P5
*
3
4.
: USB :
/
/ EQ +/
(L)(R)
(L) (R) (L)(R)2s (L)(R) (L)(R) (L) (L)(R) (R) (R) / (L)
/
4s 4s
4
SAFTY MATTERS:
1. Do not throw the product into the fire to avoid explosion. 2. The product should avoid rain, dampness or other liquids. 3. While using the product for the first time, fully charges before using it. 4. Using the earbuds for the first time, please adjust the volume to reasonably,
then gently switch to the appropriate volume, if the volume is too high, might cause tinnitus or damage to the ear and the product itself. 5. Please use the original battery, and original charger.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
5
1. 2. 3. 4.
5.
* 1. 2. 3. 4. 5. 6.
5
Adobe PDF library 16.03