NUX B-6 PRO Wireless System for Wind Instruments

Overview

The NUX B-6 PRO is a premium wireless transmission system designed specifically for wind instruments. It operates on the globally available 2.4GHz frequency band, offering automatic pairing and channel detection for effortless setup. Simply power on the transmitter (TX) and receiver (RX), and they pair within seconds. The system delivers 24-bit/48kHz audio with an advanced algorithm, ensuring stable, high-quality sound with ultra-low latency (as low as 3.6ms) and a transmission range of up to 50 meters (165 feet). Tailored frequency response curves are included to suit various wind instruments, enhancing tonal accuracy and performance. The B-6 PRO is lightweight and easy to install, primarily designed for soprano, alto, and tenor instruments, but also compatible with trumpets and other wind instruments. Its secure clip-on design attaches comfortably to the instrument without interfering with playability, addressing common sound-capture challenges. The transmitter (TX) can be docked on the receiver (RX) for charging, making it ideal for both practice and performance.

Features

• Operating Frequency Band: 2400-2483.5MHz
• Operation Range: Up to 50 m (165 ft) maximum
• Latency: >3.6ms
• Audio Quality: 24bit/48kHz
• Frequency Response: 20Hz-20kHz
• THD+Noise: Less than 0.01%@1kHz
• OUTPUT Dynamic Range: 112dBA
• TX (Transmitter) Battery Life: Up to approximately 7 hours
• RX (Receiver) Battery Life: Up to approximately 11 hours
• Booster: 0dB-12dB
• Send/Return circuit
• Digital tuner for wind instrument
• 13 preset equalization curves for wind instruments

Control Panel & I/O

TX (Transmitter)

The TX unit features a microphone with a gooseneck, a main button, charging contacts, and a USB-C port.

• Main Button: This button has an indicator light. Press it to switch between "FAVORITE EQ" equalization curves. Press and hold to turn the TX on/off. When paired with the RX, press and hold for 1.5 seconds to mute the TX, and press again to resume normal operation.
• Charging Contacts: Used for connecting to the RX (receiver) for charging.
• USB-C Port: Serves dual purposes: connecting the microphone for audio transmission and providing emergency charging for the transmitter.

Main Button Indicator Light Status

RX (Receiver)

The RX unit features an LCD screen, power button, EQ button, back button, footswitch encoder, charging contacts, 6.35mm output/send port, 6.35mm return port, 6.35mm return output port, USB-C port, DC 9V port, DI port, and ground switch.

• Power Button: Press and hold to power on/off. A short press switches to the HOME/SETTING interface. (Press and hold for 15 seconds for a device reset.)
• EQ Button: Switches between "FAVORITE EQ" curves.
• Back Button: Returns to the previous menu page.
• LCD Screen: High-definition color display.
• Charging Contacts: Magnetic connection for charging the TX.
• 6.35mm Output/Send Port: Connects to speakers or effects loops (send).
• 6.35mm Return Port: Receives signal from an effects loop (return).
• 6.35mm Return Output Port: Connects to speakers when an effects loop is used.
• Footswitch Encoder: Rotate to select menus and adjust parameters; press to confirm selections or toggle functions.
• DC 9V Port: Powers the device (requires 9V 1A adapter).
• USB-C Port: Connects to computers for firmware updates and the NUX GIF Customizer. Can also transmit audio streams.
• Ground Switch: Selects between floating or grounded DI output.
• DI Port: Connects to mixing consoles via XLR for balanced signals.

Installation

To install the system:

1. Insert the gooseneck microphone's USB-C plug into the TX transmitter's USB-C port until it clicks.
2. Press the clips on the transmitter to open them, then attach the transmitter to the edge of the instrument's mouthpiece.
3. Adjust the gooseneck microphone so the head points towards the instrument's bell at an optimal distance.

Note: Adjusting the microphone position (on-axis or off-axis to the bell) can alter the tone. Experiment to find your preferred sound.

Operating Instructions

Automatic Pairing

The B-6 PRO units are pre-paired from the factory. When powered on, they automatically connect on the best channel.

1. Turn on both the TX and RX units. They will automatically recognize and pair within seconds.
2. The RX screen will show signal input level, connection quality, and battery status for both units.
3. Attach the TX transmitter to the mouthpiece using its clip. The system is now ready for use.
4. The footswitch can be used to control the tuner or boost effect, with customizable functions available in the menu.

Manual Re-Pairing of ID

If re-pairing is needed, follow these steps:

1. Turn on the RX receiver. The screen will display "Scanning." Press and hold the "Back" button until "Pairing" appears.
2. Turn on the TX transmitter and press its "Main Button." The TX and RX will begin pairing.
3. Once successful, the screen will display "PAIRED."

Connection Scenarios

The B-6 PRO RX can connect to amplifiers or mixing consoles. Effects loops can be integrated using the send/return ports.

Description of diagrams:

• Scenario 1: Mixer -> Amplifier -> B-6 PRO RX -> B-6 PRO TX (connected wirelessly).
• Scenario 2: Mixer -> Amplifier -> Pedal -> B-6 PRO RX -> B-6 PRO TX (connected wirelessly).

Charging

Charging the RX (Receiver)

Use the provided DC 9V 1.2A power adapter. Plug it into the RX's DC port. Caution: Only use the original adapter to prevent damage.

Charging the TX (Transmitter)

There are two methods:

1. Place the powered-on RX receiver and the TX transmitter in the magnetic charging position. The TX's LED indicator will turn red while charging.
2. Use a 5V/500mA adapter with the USB-C port on the TX transmitter.

Caution: The USB-C port on the TX is not for charging the RX.

Tips and Methods to Improve Wireless System Performance

• Check for nearby Wi-Fi devices and select the best "Low Latency" or "Stable" mode for optimal transmission.
• Ensure the RX receiver is fully charged and powered on.
• Minimize obstructions between the TX and RX units.
• Reduce the distance between TX and RX, especially on stage, using a long cable to connect the RX to the console/speaker if necessary.
• Maintain at least 1 meter separation between multiple wireless systems.
• Keep the RX away from Wi-Fi access points, computers, Bluetooth devices, and other 2.4 GHz sources.
• Turn off unnecessary Wi-Fi on other devices.
• Avoid high Wi-Fi traffic activities (large downloads, streaming).
• Avoid placing TX/RX near metal surfaces or dense materials.
• Identify and avoid "blind spots" during sound checks.
• Optimal operating distance is 10m (33 ft) to 35m (115 ft).

"FAVORITE EQ" Equalization Curves Introduction

The B-6 PRO offers 13 preset EQ curves tailored for different wind instruments and playing styles.

Note on Microphone Placement: Adjusting the microphone position (on-axis or off-axis to the bell) can result in tonal variations. Experiment to find your preferred sound.

System Settings

The B-6 PRO allows customization of various settings:

• Display Settings: Adjust display brightness.
• Tuner Settings: Customize tuner display mode, bypass mode, A4 frequency, and pitch display.
• Wireless Settings: Choose between "LOW LATENCY" (approx. 3.6ms) for minimal delay or "STABLE" (approx. 9.9ms) for enhanced stability. Select the best mode based on your environment and needs.
• Footswitch Settings: Assign functions to the footswitch for "PRESS" and "HOLD" actions (e.g., MUTE, BOOST, TUNER, S/R).
• Boost Settings: Adjust the boost effect level from 0dB to +12dB.
• EQ Settings: Select from "FAVORITE EQ" presets or adjust custom "USER'S EQ" settings. The main page displays the currently active EQ.
• Output Settings: Adjust the output level.
• Language Settings: Select the system language (e.g., English, 简体中文, 繁體中文, Spanish).
• INFO: Displays the system version information.

Specifications

* Specifications may change without notice.

Accessories

• DC 9V 1.2A power adapter
• USB-C cable
• USB-C to USB-A adapter
• Windshield
• Manual
• Warranty card
• NUX logo sticker