CIM315C Compact Contactless Smart Card Reader Module

Driver Installation Procedure

The driver is signed by Microsoft and WHQL, allowing installation via Windows Update. If Windows Update fails, follow these manual installation steps.

Hardware Requirements:

• CIM315C
• PC with Windows 7 or above

Software Requirements:

• CIR315 Driver Package

Steps:

1. Connect CIM315C to PC.
2. On PC, open "Control Panel > System".
3. Open "Device Manager".
4. Select and open "Smart card readers".
5. If "Microsoft Usbccid ... (WUDF)" is shown, continue to step 5. If "CIR315 CL" is shown, the driver installation is complete.
6. Right-click and select "Update driver" (one by one).
7. Select "Browse my computer for driver software...".
8. Choose "Let me pick from a list of available drivers on my computer".
9. Select "Have Disk...".
10. Browse to the driver location, select "CIR315.inf", and click "Open" and "OK".
11. Select "CIR315 CL" and then "Next".
12. Wait for the success screen and press "Close" to complete.
13. Double-click to ensure the device changed to "CIR315 PICC" and "CIR315 SAM".
14. Done.

Operation Example

Hardware Requirements:

• ☑ CIM315C
• ☑ PC with Windows 7 or above
• ☑ ISO14443 Test Card

Software Requirements:

• ☑ Any PCSC Application (e.g., APDU.exe)

Steps:

1. Plug in the reader into the PC.
2. Open "APDU.exe".
3. Click "1. Select reader", choose "Circle CIR315 CL 0", then click "OK".
4. Tag ISO14443 Test card on CIM315C.
5. Select "T1", Message = "90 0a 00 00 01 00 00".
6. Press "2. Connect".
7. Press "3. Transmit".
8. The result will be shown on the "Answer from the card:".

Example APDU commands and responses are provided in the original document, illustrating communication with the smart card.

FCC Compliance Information

Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

Specific operational use conditions: The end product which uses the equipment must undergo full testing and apply for an original FCC ID. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

Limited modular: This equipment is applied as a Limited single-modular transmitter. The end product which uses this equipment must undergo full testing and apply for an original FCC ID.

RF Exposure warning: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end product which uses this equipment must undergo full testing and apply for an original FCC ID.

Antennas: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. The end product which uses this equipment must undergo full testing and apply for an original FCC ID.

Label and compliance information: The end product which uses this equipment must undergo full testing and apply for an original FCC ID. A label should be included and compliance to the FCC rules with the end product's FCCID.