User Manual for ATEN models including: VE2812R, HDMI HDBaseT Receiver, Audio De-Embedding
HDMI HDBaseT Receiver with Audio De-Embedding (4K@100m) (HDBaseT Class A) - VE2812R, ATEN Video Extenders | ATEN Corporate Headquarters
File Info : application/pdf, 31 Pages, 1.70MB
DocumentDocumentATEN VanCrystTM VE2812R HDMI HDBaseT Receiver with Audio De-Embedding User Manual VE2812R User Manual Compliance Statements FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Warning Operation of this equipment in a residential environment could cause radio interference. Achtung Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen verursachen. KCC Statement ii VE2812R User Manual HDMI Trademark Statement The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. RoHS This product is RoHS compliant. iii VE2812R User Manual About this Manual This user manual is provided to help you get the most from the VE2812R unit. It covers all aspects of installation, configuration, and operation. An overview of the information found in the manual is provided below. Chapter 1, Introduction introduces you to the VE2812R. Its purpose, features, installation considerations, and panel components are presented and described. Chapter 2, Hardware Setup describes the steps that are necessary to quickly and safely set up your installation. Chapter 3, Operation explains the limitations, and how to adjust audio channel using the a switch and RS-232 commands. Appendix provides a list of safety instructions and precautions, contact information for ATEN technical support, product specifications, and other technical information. Note: Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit or any connected devices. ATEN regularly updates its product documentation for new features and fixes. For an up-to-date VE2812R documentation, visit http://www.aten.com/global/en/ iv VE2812R User Manual Conventions This manual uses the following conventions: Monospaced [ ] 1. > Indicates text that you should key in. Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. Numbered lists represent procedures with sequential steps. Bullet lists provide information, but do not involve sequential steps. Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start > Run means to open the Start menu, and then select Run. Indicates critical information. v VE2812R User Manual Package Contents 1 VE2812R HDMI HDBaseT Receiver with Audio De-Embedding 1 RS-232 terminal block 4 foot pads 1 power adapter 1 user instructions Note: Make sure that all of the components are present and in good order. If anything is missing or was damaged in shipping, contact your dealer. vi Product Information VE2812R User Manual For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller. Visit ATEN on the Web for a list of locations and telephone numbers: International North America http://www.aten.com http://www.aten-usa.com User Information Online Registration Be sure to register your product at our online support center: International http://eservice.aten.com Telephone Support For telephone support, call this number: International China Japan Korea North America 886-2-8692-6959 86-400-810-0-810 81-3-5615-5811 82-2-467-6789 1-888-999-ATEN ext 4988 1-949-428-1111 vii VE2812R User Manual User Notice All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software. The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference. The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE. viii VE2812R User Manual Table of Contents Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix 1. Introduction Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Compatible Products. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. Hardware Setup Mounting the VE2812R Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connecting the VE2812R Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 RS-232 Channel Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3. Operation RS-232 Serial Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Command to Control VE2812R . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Command to Control VE2812AT / VE2812AUST / VE2812AEUT 13 Command to Control VE3912T . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Long Reach Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Appendix Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 ix VE2812R User Manual Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 x Chapter 1 Introduction Overview ATEN VE2812R is a high-quality HDBaseT HDMI receiver featuring Audio De-Embedding function. Powered by HDBaseTTM technology, the VE2812R can receive 4K HDMI signals up to 100 m over a single Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable. With HDBaseT Long Reach Mode enabled, it can deliver HDMI signals up to a maximum range of 150 meters @ 1080p. The VE2812R is HDCP2.2, HDMI compatible and guarantees reliable transmission of high-quality uncompressed HDMI signals, supporting 3D, 1080p/36bits Deep Color, 4K and embedded HD lossless audio formats. In addition, the VE2812R's built-in Audio De-Embedded function delivers S/ PDIF Coaxial or Stereo audio signals extracted from HDMI interface to an audio system that is separated from the display. The VE2812R is designed for use in meeting rooms or digital education environments where high video quality is required. Take advantage of this HDMI Extender to extend and display crystal clear, High-Definition digital signals in a reliable and efficient manner. More, VE2812R can carry on IR/RS232 from VE2812AT / VE2812AUST / VE2812AEUT / VE3912T and is recommend to be deployed in pair with the VE2812AT / VE2812AUST / VE2812AEUT / VE3912T. Users could remotely control the connected unit through RS-232 command mode via input port switching. 1 Chapter 1. Introduction Features Superior video quality 4K HDMI up to 100 m via a single Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable 1080p up to 150 m via a single Cat 5e/6 cable in HDBaseT Long Reach Mode HDMI (3D, Deep Color, 4K); HDCP 2.2 compliant Supports Audio EDID Switching (2ch Stereo, 5.1 ch Surround sound, and AUTO) Supports Audio De-Embedding - extracts audio stream from an HDMI source and delivers as a separate audio from HDMI, Coaxial S/PDIF, or Stereo audio output. Features RS-232 Serial Communication Switch - Command mode and Bypass mode to meet application requirements Supports bi-directional IR signal transmission - IR two way IR protocol delivery by one IR port; IR transmission is processed one direction at a time Firmware upgradable Built-in 8KV / 15KV ESD protection Plug-and-play Rack-mountable using the VE-RMK1U 2 Planning the Installation VE2812R User Manual Requirements Prepare the following before installing the VE2812R unit: 1 HDMI display device 1 Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable Considerations To ensure video quality, use a Cat 5e/6/6a cable. Note: For best results, ATEN recommends using the ATEN 2L-2910 Cat 6 cable. The maximum transmission distance varies at different parts of the transmission: Connection The VE2812R to a compatible ATEN Video Extender Transmitter The VE2812R to a display Interface Cat 5e/6/6a HDMI Max. Distance 100 m / 150 m (up to 1080p in Long Reach Mode) 5 m Compatible Products The VE2812R is designed to work with VE2812AT / VE2812AUST / VE2812AEUT / VE3912T, and also compatible with a wide range of ATEN video splitters, video switches, video extender transmitters, and video converters. Visit our official web site for more details. 3 Chapter 1. Introduction Components Front View 1 2 3 45 6 No. Component Description 1 audio out (coaxial) Connects to the audio in (coaxial) port on a speaker. 2 audio out (stereo) Connects to the audio in (stereo) port on a speaker. 3 audio channel switch Use the switch to set the audio channel to 2.1 ch, 5.1 ch, or auto. 4 IR port Connects to an IR emitter / receiver. 5 HDMI audio out To mute the audio on the connected HDMI display, put the switch HDMI audio out switch to OFF. 6 HDMI video out Connects to the HDMI in port on the display device. 4 Rear View VE2812R User Manual 4 1 2 3 56 No. Component 1 HDBaseT in 2 RS-232 serial port 3 RS-232 serial communication switch 4 long reach mode switch 5 firmware upgrade switch 6 power jack Description Connects to the HDBaseT output port on a compatible ATEN video transmitter via a CAT 6a/ ATEN 2L-2910 cable. Connects to an RS-232 main controller, such as a PC or Control system. Sets the RS-232 serial interface for signal Bypass or Command. For details, see page 11. Put the switch to ON to enable the long reach mode. For more details on long reach mode, see page 14. This port is reserved for ATEN Technical Support. If you would like to do a firmware upgrade yourself, please contact your dealer. Connects to the power adapter. 5 Chapter 1. Introduction LED Display You can find the unit's LEDs on the top and front panel as illustrated below. See the table below for details on LED indication. 123 No. LED Indication Description 1 HDMI out status Lights orange Video display is normal with HDCP key. LED Blinks orange Video display is normal without HDCP key. Off Video signal dropped. 2 link LED Lights orange The transmission to the display device is stable. Off The transmission to the display device is unstable. 3 power LED Lights green The unit is powered on. Off The unit is powered off. Note: The power, link LED and HDMI out Status LEDs blink at the same time to indicate that the firmware upgrade is in progress. 6 Chapter 2 Hardware Setup 1. Please review the safety information regarding the placement of this device in Safety Instructions, page 15. 2. Do not power on the VE2812R until all the necessary hardware is connected. Mounting the VE2812R Unit You can mount the VE2812R to the wall or on a rack. Wall Mounting Secure or hang the VE2812R unit to the wall using the built-in mounting brackets. Rack Mounting Use the VE-RMK 1U Rack Mount Kit to rack-mount the VE2812R. For more information about this accessory, go to https://www.aten.com/global/en/products/professional-audiovideo/accessories/ve-rmk1u/ 7 Chapter 2. Hardware Setup Connecting the VE2812R Unit Follow the steps below to connect the VE2812R to an HDMI-enabled display source, a compatible ATEN Video Transmitter, and other controls as required. audio speaker 2 IR receiver 4 HDMI display 1 VE2812AT 3 )recommended*! IR emitter 4 power 7 6 or 0 5 PC ATEN Control Box !!Control Pad 1. Connect an HDMI-enabled display to the VE2812R's HDMI out port. 2. Follow the steps below to set up your audio output. a) To use an independent speaker, connect the speaker to the VE2812R's audio out port (coaxial or stereo) using an appropriate audio cable. b) Depending on the interface of your chosen audio output device, adjust the audio signal using the audio channel switch. Audio Interface Stereo Coaxial HDMI Audio Channel Switch Description 2 ch Sets the audio output to channel 2. 5.1 ch Sets the audio output to channel 5.1. Auto Detects the supported audio channel of the connected HDMI display. Note: Stereo audio will be muted if the channel is set to CH5.1. 8 VE2812R User Manual c) To mute the audio on the connected HDMI display, put the HDMI audio switch to OFF. 3. Connect the VE2812R's HDBaseT in port to a video transmitter's HDBaseT out port using a Cat 6a/ATEN 2L-2910 cable. Note: ATEN recommends pairing the VE2812R with VE2812AT / VE2812AUST / VE2812AEUT / VE3912T. 4. (Optional) To bypass IR signals to remotely control a device (e.g. blu-ray disc) connected to the video transmitter, connect an IR receiver to the VE2812R's IR port and an IR emitter to the VE2812AT / VE2812AUST / VE2812AEUT / VE3912T's IR port. Note: To purchase an IR receiver and an IR remote control, contact your local sales representative for more information. 5. (Optional) You can use the RS-232 serial port to do one of the following: To control the VE2812AT / VE2812AUST / VE2812AEUT / VE3912T using an ATEN Control System/Control Pad, connect a Control Box / Control Pad to the VE2812R's RS-232 serial port and then put the RS-232 serial communication switch to Command. To bypass RS-232 serial control signals to a PC or a serial device, connect the PC or serial device (e.g. touch pad) to the VE2812R's RS232 serial port and put the RS-232 serial communication switch to Bypass. 6. Ground the devices connected to the VE2812R to prevent damages from power surges or static electricity. 7. Plug the power cord into the VE2812R's power jack. 9 Chapter 2. Hardware Setup RS-232 Channel Transmission You can manage the VE2812R via RS-232 serial devices, such as computers or bar code scanners. The RS-232 signal transmission flow can be illustrated as follows: Cat 5e / 6 / 6a PIN CONFIGURATION (Captive screw connectors) Tx Rx Gnd Tx Rx Gnd Tx Rx Gnd Serial Device Tx Rx Gnd From a source device, the RS-232 signal is transmitted (Tx) to the VE2812R receiving (Rx) unit; the a compatible ATEN Video Receiver transmits (Tx) signals to the display device (Rx). You can set the VE2812R to either bypass serial data or to receive RS-232 commands. By default, the VE2812R is set to bypass serial data. To set the unit to receive RS-232 commands, press the Input Switch pushbutton for 5 seconds. For details on RS-232 commands, see RS-232 Serial Transmission, page 11. 10 Chapter 3 Operation RS-232 Serial Transmission The RS-232 Serial Transmission allows you to choose whether to bypass serial data or to remotely control the VE2812AT / VE2812AUST / VE2812AEUT / VE3912T using commands depending on your installation. You can simply switch RS-232 mode between Command / Bypass by clicking the RS-232 Serial Communication Switch listed below. RS-232 6Serial Communication Switch Note: By default, the VE2812R is set to Bypass serial data. Bypass RE-232 serial data is bypassed from the controller PC or Pad to other connected devices. Command You can change the input mode on VE2812R / VE2812AT / VE2812AUST / VE2812AEUT / VE3912T using RS-232 commands. 11 Chapter 3. Operation Command to Control VE2812R To control VE2812R please refer to the table below for a list of available tasks and the corresponding commands. For example, to mute the HDMI display sound, type mute HDMI audio on and then press [Enter]. Task Command Control Mutes the HDMI display sound mute HDMI audio on Unmutes the HDMI display sound mute HDMI audio off Note: In order for the above two commands to work, the HDMI Audio Out Switch must be switched to OFF. Mutes the stereo and coaxial sound mute audio on Unmutes the stereo and coaxial sound mute audio off Note: Press [Enter] to execute a command. Reboots the unit reboot Views the current input mode settings read 12 VE2812R User Manual Command to Control VE2812AT / VE2812AUST / VE2812AEUT You can change the input mode of VE2812AT / VE2812AUST / VE2812AEUT using RS-232 commands. Refer to the table below for a list of available tasks and the corresponding commands. For example, to enable automatic switching, type swmode plugin auto and then press [Enter]. Task Control Command Input Enables automatic input switching swmode plugin auto N/A Disables automatic input switching swmode plugin off N/A Enables automatic plug-out switching swmode plugout prev N/A Disables automatic plug-out switching swmode plugout off N/A Sets the unit to the HDMI mode sw i Sets the unit to the VGA mode sw i Note: Press [Enter] to execute a command. Port N/A N/A N/A N/A 01 02 Command to Control VE3912T You can change the input mode of VE3912T using RS-232 commands. Refer to the table below for a list of available tasks and the corresponding commands. For example, to enable automatic switching, type swmode plugin auto and then press [Enter]. Task Enables automatic input switching Disables automatic input switching Enables automatic plug-out switching Disables automatic plug-out switching Sets the unit to the DisplayPort mode Command Control Input swmode plugin auto N/A swmode plugin off N/A swmode plugout prev N/A swmode plugout off N/A sw i Port N/A N/A N/A N/A 01 13 Chapter 3. Operation Task Sets the unit to the HDMI mode Sets the unit to the VGA mode Note: Press [Enter] to execute a command. Control sw sw Command Input i i Port 02 03 Long Reach Mode Long reach mode is a modulation that extends the transmission distance up to 150 m using a Cat 5e/6 cable while compromising the maximum frame rate to 1080p, 24 bpp, 60 Hz via a single Cat 5e/6 cable. To enable long reach mode, put the HDBaseT long reach mode switch to ON at either the transmitter or the connected receiver. 5 long reach mode switch ON 6 Note: When long reach mode is enabled, the VE2812R will not be able to transmit 4K signals, in which case, the output display will be blank. 14 Appendix Safety Instructions General This product is for indoor use only. Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered. The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided. Never spill liquid of any kind on the device. Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. To prevent damage to your installation it is important that all devices are properly grounded. Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over. Position system cables and power cables carefully; Be sure that nothing rests on any cables. Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock. Do not attempt to service the device yourself. Refer all servicing to qualified service personnel. 15 Appendix If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair. The power cord or plug has become damaged or frayed. Liquid has been spilled into the device. The device has been exposed to rain or water. The device has been dropped, or the cabinet has been damaged. The device exhibits a distinct change in performance, indicating a need for service. The device does not operate normally when the operating instructions are followed. Only adjust those controls that are covered in the operating instructions. Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair. 16 VE2812R User Manual Rack Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack. Always load the rack from the bottom up, and load the heaviest item in the rack first. Make sure that the rack is level and stable before extending a device from the rack. Use caution when pressing the device rail release latches and sliding a device into or out of a rack; the slide rails can pinch your fingers. After a device is inserted into the rack, carefully extend the rail into a locking position, and then slide the device into the rack. Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not exceed 80 percent of the branch circuit rating. Make sure that all equipment used on the rack including power strips and other electrical connectors is properly grounded. Ensure that proper airflow is provided to devices in the rack. Ensure that the operating ambient temperature of the rack environment does not exceed the maximum ambient temperature specified for the equipment by the manufacturer. Do not step on or stand on any device when servicing other devices in a rack. 17 Appendix Technical Support International For online technical support including troubleshooting, documentation, and software updates: http://support.aten.com For telephone support, see Telephone Support, page vii: North America Email Support Online Technical Troubleshooting Support Documentation Software Updates Telephone Support support@aten-usa.com http://www.aten-usa.com/support 1-888-999-ATEN ext 4988 When you contact us, please have the following information ready beforehand: Product model number, serial number, and date of purchase Your computer configuration, including operating system, revision level, expansion cards, and software Any error messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 18 Specifications VE2812R User Manual Function Specifications Video Output Interfaces 1 x HDMI Type-A Female (Black) Impedance HDMI: 100 Video Max. Data Rate 10.2 Gbps (3.4 Gbps per lane) Max. Pixel Clock 340 MHz Compliance HDMI (3D, Deep Color, 4K) HDCP Compatible Consumer Electronics Control (CEC) Max. Resolutions / Distances HDMI: Up to 4k @70m (Cat 5e/6) / 100m (Cat 6a/ATEN ........2L-2910 Cat6) Up to 1080p @100m (Cat 5e/6/6a) 4k supported: 4096 x 2160 / 3840 x 2160 @60Hz (4:2:0) 4096 x 2160 / 3840 x 2160 @30Hz (4:4:4) Audio Output 1 x HDMI Type-A Female (Black) 1 x Mini Stereo Jack Female (Green) 1 x SPDIF Coaxial Female (Orange) Connectors Unit To Unit 1 x RJ-45 Female Power 1 x DC Jack (Black) with locking Control RS-232 Connector s 1 x Terminal Block, 3 Pole, Type: DTE Baud Rate 115200 bps Data Bits 8 Stop Bits 1, no parity and flow control IR 1 x Mini Stereo Jack Female (Black) Power Consumption DC5V:4.98W:43BTU 19 Appendix Function Switches HDMI Mute Audio EDID Selection RS-232 Selection Long Reach Mode Switch Firmware Upgrade Environmental Operating Temperature Storage Temperature Humidity Physical Properties Housing Weight Dimensions (L x W x H) with Bracket Dimensions (L x W x H) without Bracket Specifications 1 x Slide Switch - ON/OFF 1 x Slide Switch - 2ch/5.1ch/AUTO 1 x Slide Switch - RS-232 Bypass/Command mode 1 Slide Switch - ON/OFF 1 Slide Switch - ON/OFF 0 - 40°C -20 - 60°C 0 x 80% RH, Non-Condensing Metal 0.46 Kg (1.01 lb) 14.53 x 12.30 x 3.00 cm (5.72 x 4.84 x 1.18 in.) 13.60 x 10.10 x 2.90 cm (5.35 x 3.98 x 1.14 in.) 20 VE2812R User Manual Limited Warranty ATEN warrants its hardware in the country of purchase against flaws in materials and workmanship for a Warranty Period of two [2] years (warranty period may vary in certain regions/countries) commencing on the date of original purchase. This warranty period includes the LCD panel of ATEN LCD KVM switches. Select products are warranted for an additional year (see A+ Warranty for further details). Cables and accessories are not covered by the Standard Warranty. What is covered by the Limited Hardware Warranty ATEN will provide a repair service, without charge, during the Warranty Period. If a product is detective, ATEN will, at its discretion, have the option to (1) repair said product with new or repaired components, or (2) replace the entire product with an identical product or with a similar product which fulfills the same function as the defective product. Replaced products assume the warranty of the original product for the remaining period or a period of 90 days, whichever is longer. When the products or components are replaced, the replacing articles shall become customer property and the replaced articles shall become the property of ATEN. To learn more about our warranty policies, please visit our website: http://www.aten.com/global/en/legal/policies/warranty-policy/ © Copyright 2021 ATEN® International Co., Ltd. Released: 2021-08-25 ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved. All other brand names and trademarks are the registered property of their respective owners. 21
ATEN - Simply Better Connections | ATEN U.S.A.Downloads | ATEN Corporate HeadquartersATEN - Simply Better Connections | ATEN Corporate HeadquartersProduct Warranty | ATEN Corporate HeadquartersVideo Extender Rack Mount Kit - VE-RMK1U, ATEN Accessories | ATEN Corporate HeadquartersLCD KVM Switches / Consoles | ATEN Corporate HeadquartersVideo Extender Rack Mount Kit - VE-RMK1U, ATEN Accessories | ATEN Corporate Headquarters