Instruction Manual for HUSKY models including: N2W652454W3B 3 Tier Industrial Duty Steel Freestanding Garage Storage Shelving Unit, N2W652454W3B, 3 Tier Industrial Duty Steel Freestanding Garage Storage Shelving Unit, Freestanding Garage Storage Shelving Unit, Garage Storage Shelving Unit
Husky N2W652454W3B 035441253241 0035441253241 1007784688
Husky N2W652454W3R 035441253258 0035441253258 1007587667
File Info : application/pdf, 6 Pages, 2.73MB
DocumentDocument3-SHELF STORAGE RACK RACK DE ALMACENAMIENTO DE 3 ESTANTES 65 in. W X 24 in. D X 54 in. H 1.65 m AN X 60.9 cm PR X 1.37 m AL ITEMS / ARTÍCULOS 1007784688 1007587667 MODELS / MODELOS N2W652454W3B N2W652454W3R USE AND CARE GUIDE Questions, problems, missing parts? Contact us directly for assistance: 7 a.m. - 5 p.m., CST, Monday-Friday Chat: www.edsal.com Email: support@edsal.com Phone: 1-773-475-3131 To obtain replacement parts please provide: Model Number, Part Number & Description, Store Location and Date Purchased. GUÍA DE USO Y CUIDADO ¿Preguntas, problemas o partes perdidas? Póngase en contacto con nosotros directamente para obtener ayuda: 7 a.m. - 5 p.m., CST, Lunes-Viernes Charla: www.edsal.com Correo Electrónico: support@edsal.com Teléfono: 1-773-475-3131 Para obtener partes de reemplazo por favor proporcione: Número de Modelo, Número de Parte y Descripción, Ubicación de la Tienda y Fecha de Compra US Patents & Patents pending Patentes de EE. UU. y patentes en trámite THANK YOU FOR YOUR PURCHASE / GRACIAS POR SU COMPRA Important Safety Information / Información de Seguridad Importante WARNING · Unit must be placed on a level surface or leveled with included hardware (when applicable). · Do not sit or stand on or allow children to climb, sit or stand on the assembled product. · For safety reasons, it is imperative that this unit be mounted on the wall or floor. · Unit can tip over causing severe injury or death. · Do not exceed the recommended weight limits. · Evenly distribute the weight on each level and always keep the heavier loads on the bottom. · Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury. · Contains small parts, keep children away during installation. · Use two or more people to assemble and move the unit to avoid injury. · Use care when working with metal parts, wear gloves for protection. · Do not use this unit to store aquariums. · Maximum weight capacity per shelf is 2,500 lbs. (1133.9 kg) when weight is evenly distributed; or 7,500 lbs. (3401.9 kg) total unit capacity, evenly distributed. · Do not use this unit for anything other than the manufacturer's intended purpose. · Mounting hardware not included. Consult with your local hardware dealer to find suitable hardware for securing to your floor or wall. · Periodically inspect the unit to ensure beams are properly secured to the frame. · Keep this manual for future reference. ADVERTENCIA · El producto debe colocarse en una superficie nivelada, o nivelarse con el herraje incluido (si aplica). · No siente, pare o permita que los niños suban, se sienten o se paren en el producto ensamblado. · Por razones de seguridad, es indispensable que el producto quede fijo en la pared. · El producto se puede volcar causando lesiones graves o la muerte. · No rebasar el límite de peso recomendado. · Distribuir la carga uniformemente en cada nivel y mantener siempre lo más pesado en la parte inferior. · Antes de cortar, perforar o martillar en la pared o piso, verificar la ubicación de la instalación eléctrica, tuberías y líneas de gas; cortarlas puede causar graves lesiones. · Contiene piezas pequeñas; mantenga alejados a los niños durante la instalación. · Para evitar lesiones, se necesita que dos o más personas ensamblen y muevan esta unidad. · Tenga cuidado cuando trabaje con piezas metálicas; use guantes de protección. · No utilice esta unidad para almacenar acuarios. · La capacidad de peso máxima por estante es de 2,500 lbs. (1133.9 kg) cuando el peso se distribuye uniformemente; o 7,500 lbs. (3401.9 kg) de capacidad total de la unidad, distribuida uniformemente. · No utilice esta unidad para otra cosa que no sea el propósito previsto por el fabricante. · No se incluyen herramientas de montaje. Consiga las herramientas adecuadas para asegurar el producto al piso o a la pared en una ferretería local. · Inspeccione con frecuencia la unidad para asegurarse de que las vigas estén fijadas al marco correctamente. · Conserve este manual para referencia futura. Contents / Contenido A x2 Frame Marco B x6 Beam Viga C x3 Shelf Support Soporte de repisa D x3 Wire Deck Estante de alambre PART/ PIEZAS A B C D PARTS LIST / LISTA DE PIEZAS ITEMS/ARTÍCULOS: 1007784688 MODELS/MODELOS: N2W652454W3B PART NUMBER/ NÚMERO DE PIEZA ITEMS/ARTÍCULOS: 1007587667 MODELS/MODELOS: N2W652454W3R PART NUMBER/ NÚMERO DE PIEZA N2W-FM2454-BLK N2W-BM65-BLK N2W-TB24-BLK 2360W-BLK N2W-FM2454-RED N2W-BM65-RED N2W-TB24-BLK 2360W-BLK Preparation / Préparación Before beginning assembly, read through the instructions and make sure all parts are present. Make sure when assembling the beams (B) to frames (A) the narrow end of the frame slots are facing down so the beam tabs can seat into bottom of slot (see FIG.1). A rubber mallet may be used to tap on the beam to insure the tabs are properly seated into the bottom of the slots. When connecting the beams (B), make sure the obround hole of the ledge is facing on the bottom to ensure correct assembly (see FIG.2). It is recommended to evenly space out each shelf level assembly. Antes de comenzar el montaje, lea las instrucciones y asegúrese de que todas las piezas estén presentes. El ensamblaje de esta unidad se realiza colocando los dos clips soldados ubicados en los extremos de la viga (B) en las ranuras frontales de los marcos (A). El extremo estrecho de las ranuras debe estar mirando hacia abajo. Una vez que los clips soldados están enganchados en las ranuras, se debe utilizar un mazo de goma para fijar de manera correcta los clips en el extremo estrecho de las ranuras para garantizar que esté conectado de manera segura (ver Imagen 1). Al conectar las vigas al marco, asegúrese de que el orificio de la repisa interior esté orientado hacia la parte inferior para garantizar el correcto ensamblaje (ver Imagen 2). Se recomienda espaciar uniformemente cada conjunto a nivel de estante. FIG. 1 IMAGEN 1 Narrow end of frame slots face down. Extremo estrecho de las ranuras del marco boca abajo. Backside beam tabs connect into the slots. Los clips de viga trasera se conectan a las ranuras. Inside View Vista interior FIG. 2 IMAGEN 2 The tabs should be fully engaged into bottom of slots. Las pestañas deben estar completamente comprometidas en la parte inferior de la ranura. bottom fondo When assembling beams, the abround hole faces inside at the bottom. Al ensamblar las vigas, el orificio de la repisa interior debe estar orientado hacia abajo. Helpful Tools/Items (not included): Herramientas/elementos útiles (no incluidos): · Rubber Mallet · Mazo de goma · Gloves · Guantes Assembly / Ensamblaje 1 Assemble B (x6) to A (x2) / Ensamblar B (x6) a A (x2) A A A B B Tap down Toca hacia abajo top B arriba NOTE: Make sure when installing the beam the long obround holes are at the bottom. bottom fondo NOTA: Asegúrese de que al instalar la viga los largos orificios de obround estén en la parte inferior. NOTE: When installing each pair of beams per level, be sure they are installed at the same height on both frames, front and back. Do this by simply counting the number of slots that the front beam was installed at, then making sure to install the opposite side into the same slot count. This will ensure each shelf will be leveled. NOTA: Al instalar cada par de vigas por nivel, asegúrese de que estén instaladas a la misma altura en ambos marcos, delantero y trasero. Haga esto simplemente contando el número de ranuras en las que se instaló la viga delantera, luego asegúrese de instalar el lado opuesto en el mismo recuento de ranuras. Esto asegurará que cada estante será nivelado. 2 Assemble C (x3) to beams / Ensamblar C (x3) en vigas B C C 3 Assemble D (x3) to beam assembly / Ensamblar D (x3) en el conjunto de vigas NOTE: Wire decks (D) should be installed with the long horizontal wires facing the bottom. NOTA: La cubiertas de alambre (D) debe instalarse con cables horizontales largos hacia la parte inferior. bottom D fondo Inside View Vista interior The tabs should be fully engaged into bottom of slots. Las pestañas deben estar completamente comprometidas en la parte inferior de la Warranty / Garantía GUARANTEED FOREVER. If your Husky product ever fails bring it back and we will replace it for free. This full warranty gives you specific rights which vary from state to state. If this product is defective contact the manufacturer for repair or replacement parts. GARANTIZADO PARA SIEMPRE. Si alguna vez falla su herramienta o unidad de almacenamiento Husky, devuélvala y la reemplazaremos de forma gratuita. Esta garantía completa le otorga derechos específicos que varían de estado a estado. Si este producto es defectuoso, comuníquese con el fabricante para reparar o reemplazar piezas. Retain this manual for future use. Conserve este manual para referencia futura.