GVM-SD200R V3

Important Safety Instructions

• Read the product manual carefully before use.
• Suitable for use in a temperature range of -10 to 40°C.
• Do not place near flammable and volatile solvents like alcohol and gasoline.
• Ensure the device has cooled down completely before storing. Unplug the power cord. Store in its carrying case or a well-ventilated, dry place.
• This lighting fixture is not for general illumination. Individuals with eye injuries or sensitivity should avoid using it.
• This is a professional light; children are prohibited from using it. Parents/guardians must supervise children near the equipment.
• Remove the protective cover before use.
• Do not stare directly at the light source when the fixture is on. Use high-intensity lighting only under professional guidance. Avoid prolonged exposure to high-intensity light. Discontinue use and seek medical attention if discomfort occurs.
• Use carefully when the fixture is on; avoid contact with high-temperature components like LED light sources to prevent burns.
• Do not use damaged equipment or accessories. Seek professional inspection and repair.
• If the light source is damaged or deformed due to heat, stop use and contact the manufacturer or qualified repairman for replacement.
• If the product is cracked due to falling, squeezing, or strong impact, stop use to avoid electric shock.
• Do not disassemble the product yourself. Malfunctions must be checked and repaired by the manufacturer or authorized personnel.
• Always unplug the power supply before cleaning and maintenance. Pull the plug, not the cable.
• This device shall only operate with earthed power outlets or emergency power generators.
• Do not wipe the device with a wet cloth; use a dry, soft cloth.
• If an extension cord is required, ensure it has the necessary capacity to avoid overheating.
• Properly place power cords to avoid tripping hazards or contact with hot surfaces. Use original power cords; damage from non-original cords is not covered.
• Do not use accessories not recommended by the brand to avoid fire, electric shock, or injury.
• For battery-powered products, use only specified batteries, power sources, or accessories. Keep batteries out of reach of children. Seek immediate medical attention if a battery is swallowed. Remove leaking, discolored, smoking, or odorous batteries carefully to avoid burns. Do not use deformed or modified batteries. Do not disassemble or modify batteries. Do not heat or solder batteries. Keep batteries away from fire, water, or strong external force. Ensure correct battery polarity and do not mix old/new or different battery types.
• For products with built-in lithium batteries, use a dedicated charger within the prescribed voltage and temperature range.
• The warranty lasts for one year. Consumables like batteries, adapters, and power cords are not covered.
• The one-year warranty is invalidated by private repairs.
• Malfunctions caused by non-standard operations are not covered.
• Safety instructions are based on factory testing. Design and specifications may change without notice. Visit the official website for the latest version.

Warning

High-power LED lights are strictly prohibited from being directly viewed or shining into other people's eyes. Do not unplug the power cord or connecting wires while the light is on to avoid personal injury. Do not cover the heat dissipation port when the lamp is in operation. Keep children away from touching or using this light. As professional lighting equipment, please make sure to operate it correctly according to the user manual.

Product Introduction

Thank you for purchasing the "GVM-SD200R". This product is specifically designed for photography and videography enthusiasts, suitable for live, outdoor, studio productions, and YouTube video shooting.

Main features:

• Stepless adjustment of brightness, dual color temperature output (3200K~5600K). High color rendering index (CRI 97+). COB LED beads restore true colors for natural-looking images.
• APP control via smart mobile devices.
• Built-in LCD display and stable operating system, supporting 360° rotation. Includes a standard hyper reflector to concentrate light and control fill.
• Simulates 18 different light effects: Lightning, Cop Car, Candle, TV, Bad Bulb, Party, Disco, and Paparazzi (accessible via APP, DMX, or RF).

GVM believes the correct use of this product will improve your workflow. Reading this user guide carefully is strongly recommended before use.

Disclaimers

• Read this text carefully for correct operation. Failure to follow instructions and warnings may cause harm or damage.
• By using this product, you acknowledge reading and understanding the disclaimer and warnings, and accept full responsibility for its use and consequences.
• Design and specifications are subject to change without notice.

Product Parameter

Precautions

• Use the matching power adapter with the same specifications. Do not use adapters with different output voltage parameters.
• The product is not waterproof; use it in a rainproof environment.
• The product is not anti-corrosion; avoid contact with corrosive liquids.
• Ensure the product is placed firmly to prevent falling and damage.
• If the product will not be used for a long time, switch off the power to reduce energy loss.

Product Structure Analysis

The GVM-SD200R features the following components:

• Bowens mount: For attaching accessories like reflectors and softboxes.
• Diffuser mount: Area for attaching diffusion materials.
• COB light chip: The main light source.
• U-frame: The main support structure for the light head.
• Locking T-handle: Used to secure the U-frame angle.
• Junior pin receiver: Standard mounting point for light stands.
• LCD screen: Displays current settings and parameters.
• DMX input: Port for connecting to a DMX console.
• Cooling vents: For heat dissipation via radiator and fan.
• Release slider: Mechanism for detaching accessories like the Bowens mount.
• Rosette angle locking handle: Fine-tunes and locks the tilt angle of the light.
• V-mount slot: For attaching the power adapter or battery plates.
• Mode button: Cycles through different control modes (Rotate, Master, Slave, APP, DMX).
• Compound knob: Used for adjusting parameters like brightness, color temperature, HUE, SAT, and channel. Long press switches between CCT/HSI modes.
• ON/OFF Switch: Powers the unit on and off.

Installation Method

1. Mounting to Light Stand: Rotate the locking knob clockwise to install and fix the light onto a light stand. Rotate counterclockwise to remove.
2. Attaching Bowens Mount Reflector: Place the reflector in front of the light's Bowens mount and turn it slightly clockwise to secure.
3. Removing Bowens Mount Reflector: Pull back the Bowens mount release slider while rotating the reflector counterclockwise.
4. Attaching Power Adapter: Attach the power adapter onto the V-Mount Slot of the U-frame.
5. Connecting Power: Connect the power cord to the DC input port to power the light.
6. Connecting DMX: Connect to a DMX console using a DMX adapter cable (sold separately).
7. Adjusting Angle: Loosen the angle fixing handle, adjust the spotlight's angle as needed, and then tighten the handle.

Description of Product Control Keys

The light features several control keys:

• 1. Power input: Connection point for the power supply.
• 2. ON/OFF Switch: Toggles the power state of the light.
• 3. LCD display screen: Shows current mode, parameter settings, brightness, color temperature, HUE, SAT, scene number, and channel value.
• 4. Compound knob:
  • Long press for 2 seconds to switch between CCT/HSI light modes.
  • Short press to select the parameter to be adjusted.
  • Turn the knob to adjust the selected parameter's value.
• 5. Mode button: Switches between control modes: Rotate, Slave, Master, APP, DMX.
• 6. DMX Interface: Ports for DMX console input and output.

Function Introduction & Instructions for Use

LCD Display

The LCD screen displays:

• Brightness
• Control mode (e.g., Master, Slave, APP, DMX)
• Light mode (e.g., CCT, HSI)
• Light parameters (e.g., Color Temperature, HUE, Saturation, Time)
• Scene number (when applicable)
• Channel number

Parameters are displayed only when controlled by APP, DMX, or RF.

Mode Types and Functions

Press the Mode button to cycle through:

• Rotate mode: Adjusts light mode and parameters, but not channel value.
• Master mode: Controls brightness, color temperature, and channel synchronously for itself and any slaved lights set to the same channel.
• Slave mode: Channel number can be adjusted via the compound knob. Synchronous control is achieved when the slave's channel matches the master's.
• APP mode: Channel number adjustable via the compound knob; full control via the mobile APP.
• DMX mode: Settings controlled via a connected DMX console.

Adjusting Parameters

• Brightness (BRG): In Master/Rotate mode, short press the TAB button (or rotate knob) to select brightness and adjust with the knob. In APP mode, use the mobile app. In DMX mode, use the DMX console.
• Color Temperature (CCT): In Master/Rotate mode, long press TAB for 2 seconds to switch to CCT mode, short press TAB to select color temperature, then adjust with the knob. In APP mode, use the mobile app. In DMX mode, use the DMX console.
• HUE: In Master/Rotate mode, long press TAB for 2 seconds to switch to HSI mode, short press TAB to select HUE, then adjust with the knob. In APP mode, use the mobile app. In DMX mode, use the DMX console.
• Saturation (SAT): In Master/Rotate mode, long press TAB for 2 seconds to switch to HSI mode, short press TAB to select SAT, then adjust with the knob. In APP mode, use the mobile app. In DMX mode, use the DMX console.
• Channel (CH): In Slave, APP, or DMX mode, adjust the channel using the compound knob. In APP mode, also adjustable via the mobile app.
• Scene (SC): Accessible via APP, DMX, or RF. Features 8 scenes: Lightning, Cop Car, Candle, TV, Bad Bulb, Party, Disco, Paparazzi. In Slave mode, sync scenes with an RF remote (sold separately) by matching channels. In APP mode, use the mobile app. In DMX mode, use the DMX console.

APP Control

To control the light via the GVM LED APP:

1. Switch the video light to APP mode.
2. Open the GVM LED APP (download via QR code on manual). Register/login.
3. Enter the Bluetooth search interface. Find and connect to "BT_LED".
4. Upon successful connection, the APP control interface will appear, allowing control of the light and any slaves on the same channel.
5. Note: Do not pair via the phone's system Bluetooth settings; connect directly through the APP.

Master & Slave Control Mode

To control multiple lights synchronously:

1. Set one light to Master mode.
2. Set other lights to Slave mode and ensure they are on the same channel (CH) as the master.
3. The master light will then synchronously control brightness and color temperature. The APP can also connect to the master to control slaves.

DMX Control

Connect the DMX console to the video light using a DMX cable. Set both the light and the console to the same channel to enable control via the DMX console.

APP Control Details

The GVM LED APP provides comprehensive control:

1. Download the APP by scanning the QR code provided in the manual.
2. Ensure the light is in APP mode and the phone's Bluetooth and necessary permissions (like GPS for Android) are enabled.
3. Open the "GVM LED" application. Navigate to the Bluetooth search interface (Figure 1), locate "BT_LED", and connect.
4. Once connected, the APP control interface (Figures 2, 3, 4) becomes active, allowing full control of the connected light and any slave units on the same channel.
5. Note: Avoid pairing via the phone's system Bluetooth settings; always use the APP for connection.
6. Custom Scenes: Save up to 6 custom light effects in "My Scenes". After setting parameters, tap the save icon [save-icon] in the top right corner, confirm "Save Current Scenes" by clicking "OK". These saved effects will be available in "My Scenes". (Figure 5)

Figure 1: Illustrates the Bluetooth search interface within the GVM LED APP.

Figures 2, 3, 4: Showcase the various control interfaces available within the GVM LED APP for managing the light.

Figure 5: Depicts the interface for saving custom light effects to "My Scenes".

Use and Preservation

• Avoid placing the product in high humidity, strong electromagnetic fields, direct sunlight, or high-temperature environments.
• Disconnect power if the product will not be used for an extended period.
• Cleaning: Disconnect power before cleaning. Use a damp cloth, avoiding detergents or soluble liquids that could damage the surface.
• Power: Ensure the power supply is within the specified range.
• Repairing: Do not attempt to unpack the shell if a fault occurs; contact GVM for service to avoid damage and loss of warranty.
• Accessories: Use only manufacturer-provided or approved accessories for optimal performance.
• Warranty: Modifying the product voids the warranty.

Quick Troubleshooting

Packing List

Product Warranty

This warranty card is proof for applying for warranty service. Please fill it out with the salesperson and keep it properly.

Product Information:

• Model Number: GVM-SD200R
• Product Barcode: [Barcode information would be here]
• Name: LED Video Lights
• Contact Number: [User's contact number]
• Mailing Address: [User's mailing address]

Seller Information:

• Name: [Seller's name]
• Contact Number: [Seller's contact number]
• Mailing Address: [Seller's mailing address]
• Sales Date: [Date of sale]
• Remarks: [Any remarks]

Note: This form should be confirmed by the salesperson's stamp.

Applicable Products

This document applies to products listed in the relevant "Product Warranty Information". Other products or components not covered (e.g., promotional items, added components) are not included.

Warranty Period

The warranty period is based on the "Product Warranty Information". It starts from the first day of purchase, as registered on the warranty card.

How to Obtain Warranty Service

Contact the product salesperson, an authorized service agency, or GVM's aftersales service hotline. Provide a valid warranty card as proof of purchase. GVM may provide service without a card if the product is confirmed within warranty scope, but this is not obligatory.

Cases Where Warranty Does Not Apply:

• Product or parts exceeding the warranty period.
• Malfunctions or damages from incorrect use, maintenance, storage (improper handling, unintended use, incorrect device insertion/removal, drops, crushing, exposure to inappropriate temperatures, solvents, acids, alkalis, water immersion, damp environments).
• Malfunctions or damages from unauthorized installation, repair, modification, addition, or disassembly.
• Alterations or removals of original identification information.
• Lack of a valid warranty card.
• Malfunctions or damages from unauthorized, non-standard, or unreleased software.
• Malfunctions or damages from force majeure or accidents.
• Other malfunctions or damages not caused by product quality issues. GVM is not liable for these.
• Malfunctions or damages caused by components, accessories, or software not covered by warranty that render the product unusable.
• Normal fading, wear, and consumption during product use.

Product Warranty and Service Support Information

Consumable or electrically sensitive parts are not covered by the warranty.