Flysocks PF260 Laser Rangefinder User Manual

Safety Instructions

Warning

• Do not stare into the laser beam, as it may damage your eyes.
• Do not aim the device at the sun directly, as this may permanently damage the internal components and your eyes.
• The storage temperature of the device is -10 ~ 60°C / 14 ~ 140°F. Operating outside this range may damage the device.

Environment Protection

This product contains a built-in 1000 mAh lithium battery. Do not dispose of it with household waste per local regulations.

Notice

• To protect the lens coating, do not touch the lens with your fingers.
• This laser rangefinder has been precisely calibrated. Do not disassemble, or you may void the warranty.
• Clean the lens with the included microfiber cloth to avoid damage. Do not use rough cloths.
• Avoid impact and heavy loads when carrying or using this device.
• Keep the device away from extreme heat or corrosive materials.
• Please keep it in a dry, cool, and well-ventilated place to avoid moisture, direct sunlight, dust, and temperature mutation.
• Fog can interfere with the laser ray-path, reducing measurement accuracy.
• This device has an IP54 weatherproof rating. Do not expose it to heavy rain or submerge in water.

Package Content

• Laser Rangefinder: The primary device for measuring distances.
• Portable Soft Case: A protective case for carrying the rangefinder.
• Charging Cable: Cable for recharging the device's battery.
• Microfiber Cloth: A soft cloth for cleaning the lens.
• Hand Rope: A lanyard for securing the device to your wrist.
• User Manual: This document.

Product Introduction

The Flysocks PF260 Laser Rangefinder features a compact design with several key components:

Diagram showing the front and side views of the rangefinder with numbered parts.

• 1. Eyepiece Knob: Rotate to adjust focus.
• 2. Eyepiece: For viewing the target and display.
• 3. Status LED: Red light indicates charging mode; green light indicates fully charged.
• 4. Power Button: Short press to measure; long press to lock the flag.
• 5. Mode Button: Short press to switch modes; long press to switch units (M / Yd).
• 6. Slope Switch: Toggle to enable/disable the slope compensation function.
• 7. Laser Emitter Lens: Emits the laser beam for measurement.
• 8. Laser Receive Lens: Receives the reflected laser beam.
• 9. Magnetic Stripe: Allows attachment to magnetic surfaces.
• 10. USB-C Charging Port: Port for charging the device.
• 11. Lanyard Hole: For attaching the hand rope.

Display Information

The device's display provides various indicators and readings:

Diagram showing the rangefinder's digital display with numbered elements.

• 1. Low Battery Indicator: Shows when the battery is low.
• 2. Measured Distance (Linear Distance) / Units: Displays the measured distance and its unit (e.g., Yd, M).
• 3. Flag Lock Icon: Indicates when the flagpole is successfully locked.
• 4. Measuring Reminder: A visual cue that measurement is in progress.
• 5. Slope Icon / Height Icon / Reading / Units: Displays slope compensation, calculated height, or other readings with units.
• 6. Angle Icon / Reading / Angle Unit / Speed Unit: Shows measured angles or speed with their respective units.
• 7. Two-Points Height Icon: Indicates the two-point height measurement mode.
• 8. Crosshairs: The aiming reticle for targeting.

How to Use

1. ON / OFF

   Short press the Power Button to turn the device ON. It will automatically power OFF after 30 seconds of inactivity.

2. Distance Measurement

   Adjust the eyepiece to focus on the target before measuring. If the target reflection is weak or beyond the measuring range, the display will show "---". Measurement range is influenced by target material, angle, weather visibility, and other factors. Smoother, brighter targets with larger areas and perpendicular beams generally yield longer ranges, especially in clear, non-foggy conditions.

3. Golf Slope Mode (with Flagpole Lock Function)

   Short press the Mode Button to enter Golf Slope Mode. Aim at Target B and short press the Power Button; the screen will display Linear Distance, Ballistic Distance, and Angle α. Long press the Power Button to activate the Flagpole Lock Function. Aim at Target B and sweep back and forth; the [flagpole lock symbol] will flash. When the flagpole is locked, the device will vibrate, and the screen will display Linear Distance, Ballistic Distance, and Angle α. Sweeps are more likely to trigger a lock when there is a background behind the flagpole.

   Diagram illustrating Golf Slope Mode: Target A, Target B, flagpole, ballistic curve, linear distance, and angle α.

4. Two-Point Height Mode

   Short press the Mode Button to enter Two-Point Height Mode. Aim at Target B and press the Power Button to get the Linear Distance AB and Angle α. Then, aim at Target C and press the Power Button to get the Linear Distance AC and Angle β. The screen will display Height H and Angle θ(α-β).

   Diagram illustrating Two-Point Height Mode: Target A, Target B, Target C, height H, angles α, β, and θ.

5. Auto Height Mode

   Short press the Mode Button to enter Auto Height Mode. Aim at Target B and press the Power Button; the screen will display Linear Distance AB, Height H, and Angle α.

   Diagram illustrating Auto Height Mode: Target A, Target B, Target C, height H, and angle α.

6. Horizontal Mode

   Short press the Mode Button to enter Horizontal Mode. Aim at Target B and press the Power Button; the screen will display Distance L and Angle α.

   Diagram illustrating Horizontal Mode: Target A, Target B, distance L, and angle α.

7. Speed Mode

   Short press the Mode Button to enter Speed Mode to activate speed measurement. Aim at Target B and move slightly; the speed of B can be measured accordingly.

   Diagram illustrating Speed Mode: Target B, direction of motion, and angle α.

   Notes:

   • Speed measurement range: 18~300 km/h.
   • Angle α must be less than 10°; the smaller the angle, the higher the accuracy.

Specifications

Compliance Information

FCC Compliance Information Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

Compliance logos include: CAUTION: CLASS 1 LASER PRODUCT, BSCI, ROHS, Reach, FDA, CE, FC, WEEE.

Manufacturer and Contact Information

Manufacturer: Shenzhen Mileseey Technology Co., Ltd.

Address: No.3601 Block A, Tanglang Town Plaza West, Fuguang Community, Taoyuan Street, Nanshan District, Shenzhen, China

Supervisor: MountTech HK Limited

Address: 19H Maxgrand Plaza No.3 Tai Yau Street San Po Kong, KL, Hong Kong

Made in: China