Instruction Manual for Worthington Direct models including: 940S-EV6, P-V940S, T-EV72-S, 33-02-0007, 33-05-0029, 33-03-0012, 61X-XXX6 Inground Bench with Back, 61X-XXX6, Inground Bench with Back, Bench with Back, with Back
2/ 19/ 2015 Pa g e 1 o f 10 SAFETY WARNINGS & EQUIPMENT INSPECTION · Owners and installers please note these safety warnings and make use of this checklist on a regular basis. · Follow installation instructions when erecting equipment. · Ground surfaces around equipment should be restored as needed. Concrete footings should never be exposed. Surface depth should comply with ASTM and CPSC specifications. · Check for and repair damage caused by wear or vandalism, a major factor in injury causing situations. · All protruding bolts should be covered or cut off and finished smooth. Sharp edges on pipes should be capped or removed. Check for bent, broken, or severly worn pipe, and replace. · All equipment should be free of rust and repainted whenever necessary to deter rusting. · We provide our customers with layout sheets and installation instructions. Please keep on file the specifications sheet that contains the listing of every part used. · Never add components not intended for use with this product. · Regular maintenance is necessary in this and all park and recreational equipment to insure the safety of the user. · Note: Proper maintenance of equipment requires regular tightening of all bolts, nuts, and setscrews. · Note: Regular checking of all parts, castings, etc. should be made. If a part is broken or worn, it shoud be replaced immediatly. · Check to be sure all fittings are tight and that bars and pipes do not move. · Replace all worn S-hooks. S-hooks must be completely closed. Failure to close S-hooks can result in serious injury to the user. NEVER reuse S-hooks. · Test for free movement of swing hanger and other moving attached parts. · Check for worn chains and replace them. · A soft resilient surface should be placed under all swings extending at least twice the height of the top rail both front and back. 2/ 19/ 2015 Pa g e 2 o f 10 HARDWARE 5/16" x 1" Machine Bolt 5/16" Washer 5/16" Kep Nut 2/ 19/ 2015 Pa g e 3 o f 10 TOOLS REQUIRED 1/2" Wrench 1/2" Socket Wrench Tape Measure Level 2/ 19/ 2015 Pa g e 4 o f 10 PRODUCT SPECIFICATIONS INGROUND BENCH WITH BACK Seats & Back: 11 gauge die formed angle frame 1"x1-7/8" with 3" radius corners. 3/4" #9 steel expanded metal. 10 gauge x 1-1/2" flat bar center support and mounting bracket understructure. Electrically MIG welded. Coating: Oven fused functionalized polyethylene copolymer-based thermoplastic. Fluidized bed coating application with superior mechanical performance, impact resistance and UV-stability. Frame: 2-3/8" O.D. x 12 gauge pre-galvanized structural steel tubing. Seat/back support is bent over a mandrel through the bend radius producing a wrinkle free bend. Tube ends are pre-galvanized steel capped. Seat mounting points are 7 gauge x 1-1/2" die stamped steel flat bar. All electrically MIG welded. Frame Coating: Electrostatic powder coated application oven cured. Hardware: All stainless steel hardware fasteners. Dimensions: 6' bench inground with back. Seats and back 10" wide x 72" long. Seat height is 18", seat back height is 34". Total depth of seat with back is 21-1/2". 2/ 19/ 2015 Pa g e 5 o f 10 COMPONENTS 2 1 ITEM NO. 1 2 3 4 5 2/ 19/ 2015 PartNo P-V940S T-EV72-S 33-02-0007 33-05-0029 33-03-0012 DESCRIPTION QTY 940 In Ground Leg 2 6' x 10" expanded seat 2 5/16" SS Washer 16 5/16" x 1" Machine Bolt (SS) 8 5/16" Kep Nut (SS) 8 5 4 3 Pa g e 6 o f 10 STEP 1 4 3 5 2 Attach the seat plank to the 940 legs using specified hardware. 2/ 19/ 2015 Pa g e 7 o f 10 STEP 2 2 Repeat Step 1 for the back. 2/ 19/ 2015 Pa g e 8 o f 10 FOOTINGS Estimated Required Concrete: 7 - 50 lb. Bags of Concrete 12" X2 51 3/4" 2/ 19/ 2015 18" 18" 12" 18" 18" 12" Pa g e 9 o f 10 OVERALL DIMENSIONS 72" Ground Level 2/ 19/ 2015 34 1/16" 18" 49 11/16" 21 9/16" 10" Pa g e 10 o f 10Acrobat Distiller 9.0.0 (Windows)