Klein Tools 93LCLG Self-Leveling Green Cross Line Laser Level

Product Overview

The Klein Tools 93LCLG is a self-leveling laser alignment instrument designed to project horizontal and/or vertical cross lines, and plumb spots directly above or below the instrument for precise alignment and layout applications.

Key Features:

• Horizontal and Vertical Cross Lines
• Plumb Spot
• Model: 93LCLG
• Ingress Protection: IP54 (Dust & Water Resistant)

This manual is available in English, Español, and Français.

General Specifications

• Operating Altitude: 6562 ft. (2000 m)
• Relative Humidity: <80% non-condensing
• Operating Temperature: 20°F to 115°F (-10°C to 45°C)
• Storage Temperature: -5°F to 140°F (-20°C to 60°C)
• Lasers:
  • 515-530 nm (cross lines)
  • 630-680 nm (plumb spots)
  • ≤1mW each beam, Class II Laser Product
• Accuracy:
  • Vertical & Horizontal Beams: ±3/32" per 33' (±2 mm per 10 m)
  • Plumb Up Spot: ±1/8" per 33' (±3 mm per 10 m)
  • Plumb Down Spot: ±5/32" per 33' (±4 mm per 10 m)
• Battery Type: 3 x 1.5V AA Alkaline
• Dimensions: 5.3" x 5.0" x 2.8" (134 x 127 x 65 mm)
• Weight: 26 oz. (820 g) without batteries
• Calibration: Accurate for one year
• Standards: Conforms to EN61326-1:2013, EN60825-1:2014. Complies with 21 CFR 1040.10 and 1040.11 (except for deviations pursuant to laser notice No. 50, dated June 24, 2007).
• Ingress Protection: IP54 Dust & Water Resistant
• Electromagnetic Environment: IEC EN61326-1:2013. Meets requirements for use in basic and controlled electromagnetic environments.

Specifications subject to change.

Warnings

▲ WARNINGS

To ensure safe operation and service of the instrument, follow these instructions. Failure to observe these warnings can result in serious personal injury, fire, or electrical shock. Retain these instructions for future reference.

WARNING: LASER RADIATION. DO NOT STARE INTO BEAM. Class II Laser.

Warning Label Description: The label on the side of the 93LCLG displays the model number, product name, website (www.kleintools.com), laser specifications (Max. Output ≤1mW, Wavelength), compliance information (21 CFR, EN 60825-1), and cautionary text such as "AVOID EXPOSURE: LASER RADIATION CAUTION DO NOT STARE INTO BEAM" and "CLASS II LASER PRODUCT CAUTION: LASER RADIATION WHEN OPEN". It also includes symbols for CE, WEEE disposal, IP54, and laser warnings.

General Safety Precautions:

• Exposing eyes to laser radiation can cause severe and permanent eye injuries. NEVER look directly into the laser beam.
• Do not use the instrument if it appears damaged.
• Do not modify the instrument, as this could result in hazardous laser radiation emission.
• Do not use optical equipment (lenses, prisms, scopes) to view the laser beam.
• This product should only be used by trained operators who have read and understood the instructions.
• Avoid use in locations where accidental exposure to the laser beam is possible.
• Power off the instrument after use to minimize risks of inadvertent exposure.
• Do not remove warning labels.
• Securely locate the instrument in a tidy work environment to prevent damage from drops or movement.
• The instrument is IP54 dust & water resistant. Dry with a lint-free cloth if contacted with water.
• There are no user-serviceable parts inside the instrument.

Feature Details

The instrument features various components for operation and mounting:

Views of the Instrument

• BACK View: Shows mounting points (14, 15).
• SIDE View: Displays the instrument's profile.
• TOP View: Features buttons for line control (1, 2, 3), indicators (4, 5), the power/pendulum switch (6), laser apertures (7, 8, 9, 10), tripod mounts (12, 13), magnetic mount bracket (14), magnets (15), and the clamp-on wall adapter (16).
• BOTTOM View: Shows the battery compartment door (11).

Component List:

1. Horizontal Line On/Off Button
2. Vertical Line On/Off Button
3. Plumb Spot On/Off Button
4. Low Battery Indicator (Red light indicates low battery)
5. Excessive Tilt Indicator (Blinks when instrument is tilted beyond self-leveling range)
6. Power/Pendulum Lock/Unlock Switch (Locks pendulum for transport, unlocks for self-leveling)
7. Pendulum with Lasers (Enables self-leveling)
8. Horizontal Line Aperture (Emits horizontal laser line)
9. Vertical Line Aperture (Emits vertical laser line)
10. Plumb Spot Aperture (Emits plumb spot laser)
11. Battery Compartment Door
12. 1/4-20 Tripod Mount
13. 5/8-11 Survey Tripod Mount
14. Magnetic Mount Bracket (For attaching to magnetic surfaces)
15. Magnets (Integrated into the bracket)
16. Clamp-On Wall Adapter (For mounting to beams or walls)

Note: This product contains no user-serviceable parts.

Symbols on Instrument:

• Vertical Laser Line (Green): Symbol indicating the green vertical laser beam.
• Horizontal Laser Line (Green): Symbol indicating the green horizontal laser beam.
• Plumb Spot Laser (Red): Symbol indicating the red plumb spot laser.
• Low Battery Indicator: Symbol for the low battery warning light.
• Excessive Tilt Indicator: Symbol for the tilt warning light.
• Battery Polarity: Symbol indicating correct battery installation (+/-).
• IP54 Rating: Symbol indicating Ingress Protection against dust and water.
• Laser Warning Symbol: Depicts hazardous laser radiation; "DO NOT stare into beam or view directly with optical instruments".
• Warning or Caution Symbol: General warning symbol.

Operating Instructions

Turning Laser Beams ON/OFF

Press the ON/OFF buttons (1, 2, 3) for the horizontal line, vertical line, and plumb spot respectively. These buttons are only active when the Pendulum Lock/Unlock Switch (6) is in the unlocked position. If the switch (6) is moved to the locked position while lasers are active, they will turn OFF. Laser lines can be operated independently or simultaneously.

Image Description: Visuals show the instrument projecting a horizontal laser line, a vertical laser line, and a plumb laser line.

Note on Plumb Spot: The plumb spot projects beams both upward and downward. The downward beam can locate a point on the floor, while the upward beam projects to the ceiling.

Pendulum Slider Switch & Self-Leveling

The laser assemblies are mounted on a pendulum for automatic self-leveling. The Pendulum Slider Switch (6) must be in the unlocked position for self-leveling. If the instrument is tilted more than 4° from the horizontal plane, it will not self-level. The active laser beams will flash, and the Excessive Tilt Indicator (5) will blink to signal that the instrument is not level. Reposition the instrument on a more level surface for proper self-leveling function.

Note: If the instrument indicates it is not level (flashing beams or blinking indicator 5), do not use it for layout work.

Note: After use, turn OFF the laser beams and place the Pendulum Slider Switch (6) in the locked position before storage.

Mounting Options

Magnetic Mounting Bracket (14)

The instrument attaches to a magnetic mounting bracket. This bracket can be magnetically attached to steel structures like studs, ducts, beams, and doors. It also features a keyhole for mounting with a screw or nail onto non-magnetic structures. Once mounted, the instrument can be rotated 360° on the bracket to direct the laser beams.

Image Description: Shows the bracket attached via magnet to a metal surface and via keyhole to a wall.

Clamp-On Wall Adapter (16)

This adapter can be clamped to a structural beam or a wall bracket for suspended ceilings, providing a steel surface for the magnetic mounting bracket. Once magnetically attached, the instrument can be positioned to project the laser line. The adapter also has a keyhole for screw or nail mounting.

Image Description: Shows the adapter mounted on a ceiling bracket and attached via keyhole to a wall.

Maintenance

Battery Replacement

When the Low Battery Indicator (4) illuminates red, batteries must be replaced.

1. Open the battery compartment door (11).
2. Remove and recycle three spent AA batteries.
3. Install new batteries, noting correct polarity.
4. Close the battery compartment securely.

Image Description: Shows three AA batteries being inserted into the battery compartment, illustrating correct polarity (+/-).

Cleaning

Ensure the meter is turned OFF. Wipe with a clean, dry, lint-free cloth. Do not use abrasive cleaners or solvents.

Storage

Remove batteries if the instrument will not be used for an extended period. Do not expose to high temperatures or humidity. After storage in extreme conditions, allow the instrument to return to normal operating conditions before use.

Warranty

For warranty information, visit: www.kleintools.com/warranty

Disposal/Recycle

Do not dispose of the equipment or accessories in household trash. Dispose of items according to local regulations. For more information, visit www.epa.gov or www.erecycle.org.

Customer Service

KLEIN TOOLS, INC.
450 Bond Street
Lincolnshire, IL 60069
Phone: 1-877-775-5346
Email: customerservice@kleintools.com
Website: www.kleintools.com