XPR Group - Safe access systems provider
Installation Guide for xpr models including: B100-SA Standalone Biometric Reader, B100-SA, Standalone Biometric Reader, Biometric Reader, Reader
B100-SA - XPR Group
File Info : application/pdf, 12 Pages, 2.19MB
DocumentDocumentB100-SA v2 EN Standalone Biometric Reader INSTALLER'S MANUAL www.xprgroup.com 1 Rev. 1.01 - 31.03.2022 CONTENTS 1. INTRODUCTION 3 2. MOUNTING 3 3. SPECIFICATIONS 4 4. APPLICATION DIAGRAM 4 5. RECOMMENDED SWIPING TECHNIQUE 4 6. INDICATION 4 7. WIRING 5 8. ADDING ADMIN FINGER 5 9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT 6 Pairing B100-SA v2 with DINRTT 6 Pairing B100-SA v2 with RTT 6 Pairing B100-SA v2 with RU2 6 10. ADMINISTRATOR PROGRAMMING 7 ADD finger relay 1 7 ADD finger relay 2 7 ADD finger relay 1&2 7 DELETE finger 7 DELETE ALL fingers 8 CHANGE ADMIN finger 8 CHANGE INSTALLER finger 8 Administrator programming block diagram 9 11. INSTALLER PROGRAMMING 10 Set relay 1 time 10 Set relay 2 time 10 BUZZER ON/OFF 10 BACKLIGHT ON/OFF 10 Installer programming block diagram 11 www.xprgroup.com 2 1. INTRODUCTION B100-SA v2 is access control fingerprint reader designed for easy management of the users and configuration. The scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like: - making almost impossible to make fake copy of the users fingers - same performance in the different light conditions - good reading of fingers with stains from daily jobs Built in strong scanning and matching algorithm provides excellent tolerance in the way finger is swiped over the sensor reducing to minimum the need to repeat finger swiping at the sensor. The reader can store up to 100 finger templates. One template is reserved for User manager (Administrator), one template is reserved for Reader configuration (Installer) and up to 98 templates are for Users. RECOMMENDATIONS Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he leaves the site to enroll your finger as administrator. NOTES The Reader is using physical roughness of the fingerprint to scan the finger. Some of the users may have very flat fingertips, making difficult for the sensor to recognize correctly the fingerprint. In most cases, these are children and older persons. To solve this problem, do the following: 1. Try with different user's fingers to find the "best" finger. 2. Check with the installer other models of the reader with added card reader or keypad for other type of access. MAINTENANCE No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use chemicals and materials that can scratch the sensor. WARNING! Do not touch the sensor with other objects than finger. Do not pour or splash with water or other liquids. When painting or construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint. If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled according to all national laws and regulations. 2. MOUNTING Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna. Do not place the device near or above heating equipments. If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel. Do not let children touch the device without supervision. Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can't be entered. The operating temperature of the product is between 0ºC - + 50ºC. XPRTM cannot guarantee the functionality of the product if measures and advice before are not followed. www.xprgroup.com 3 3. SPECIFICATIONS Fingerprint Capacity: Output: Push Button Input: Panel Connection: Door Open Time: Entry Mode: Programming: Admin/Installer Fingers: Backlight ON/OFF: Buzzer ON/OFF: Firmware upgrade: Current Consumption: Power Supply: Indication: IP Factor: Operating Temperature: Operating Humidity: Dimensions(mm): 98 templates 1 x Relay (2 A /24V AC/DC) Yes Cable, 0.5 m Pulse (1 to 30 seconds) or Toggle (ON/OFF) Finger By swiping 1 Administrator and 1 Installer Finger Yes Yes via RS-485 converter and windows application 100 mA max. 9-14 V DC Tricolor Status LED IP54 (internal use only) 0°C to +50°C 5% to 95% RH without condensation 92 x 51 x 25 (metal); 92 x 51 x 27 (ABS) 4. APPLICATION DIAGRAM Unsecured Area 5. RECOMMENDED SWIPING TECHNIQUE Follow the below instructions for correct finger swiping. Starting from the first finger joint, place the selected finger on the swipe sensor and move it evenly towards oneself in one steady movement. Result: For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep) For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps) 6. INDICATION www.xprgroup.com 4 7. WIRING 8. ADDING ADMIN FINGER 1.Push dip switch no.2 in position ON. 2.Reset the Power of the device. 3.Wait for One long + multiple short beeps 4.Put the dip switch in position OFF. (short beeps will stop) 5.Wait for about 15 seconds for the LED to blink in Orange. 6.Swipe the Master finger min.6 times. (Until Ok Beep) Warning: This procedure also deletes all the users and the installer finger. Warning: This procedure will unpair the connected relay unit (RTT, DINRTT or RU2) www.xprgroup.com 5 9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of request-to-exit push button. Follow the instructions bellow to pair (couple) both devices or refer to the Remote Relay's Manual. Pairing B100-SA v2 with DINRTT 1. Close the Jumper. DINRTT beeps continuously and the red led blinks. 2. Open the Jumper 3. Wait for Beep + OK Beep (short + short + long beep) After the OK beep, the coupling is done. Pairing B100-SA v2 with RTT 1. Put Dipswitch No.1 to position ON. RTT beeps continuously and the red led blinks. 2. Put Dipswitch No.1 to position OFF. 3. Wait for Beep + OK Beep (short + short + long beep) After the OK beep, the coupling is done. Pairing DINB100-SA with RU2 1. Put the Jumper to closed position. RU2 beeps continuously and the red led blinks. 2. Put the Jumper to open position. 3. Wait for Beep + OK Beep (short + short + long beep) After the OK beep, the coupling is done. Warning: Changing the ADMIN finger will also unpair the remote relay unit. www.xprgroup.com 6 10. ADMINISTRATOR PROGRAMMING Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at the end of the system installation. Initial enrollment of the Admin finger is described in installer manual. ADD Finger Relay 1 (Finger that will activate relay 1) Action Swipe Admin Finger 1 time Wait 5 seconds (until fast blinking) Swipe User Finger min. 6 times (until short + long beep) Finger x 1 x 6 Backlight slow blinking fast blinking Buzzer Sound short beep short beep short + long beep ADD Finger Relay 2 (Finger that will activate relay 2) Action Finger Backlight Buzzer Sound Swipe Admin Finger 2 times x 2 Wait 5 seconds (until fast blinking) slow blinking short beep short beep Swipe User Finger min. 6 times (until short + long beep) x 6 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays (DINRTT and RU2). Consult the installer if Relay 2 is available in your system. ADD Finger Relay 1&2 (Finger that will activate relay 1&2) Action Swipe Admin Finger 3 times Wait 5 seconds (until fast blinking) Swipe User Finger min. 6 times (until short + long beep) Finger x 3 x 6 Backlight slow blinking fast blinking Buzzer Sound short beep short beep short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays (DINRTT and RU2). Consult the installer if Relay 2 is available in your system. DELETE Finger Action Swipe Admin Finger 4 times Wait 5 seconds (until fast blinking) Swipe User Finger Finger x 4 x1 Backlight slow blinking fast blinking Buzzer Sound short beep short beep short + long beep www.xprgroup.com 7 DELETE ALL Fingers Action Swipe Admin Finger 4 times Wait 5 seconds (until fast blinking) Swipe Admin Finger 2 times Finger x 4 x2 CHANGE ADMIN Finger Action Swipe Admin Finger 5 times Wait 5 seconds (until fast blinking) Swipe NEW Admin Finger min.6 times Finger x 5 x6 CHANGE/Enroll INSTALLER Finger Action Swipe Admin Finger 6 times Wait 5 seconds (until fast blinking) Swipe NEW Installer Finger min.6 times Finger x 6 x6 Backlight slow blinking slow blinking fast blinking Backlight slow blinking slow blinking fast blinking Backlight slow blinking slow blinking fast blinking Administrator Programming block diagram Swipe the ADMIN Finger 1 to 6 times depending of the desired menu Buzzer Sound short beep short beep multiple beeps Buzzer Sound short beep short beep short + long beep Buzzer Sound short beep short + long beep 3 short beeps www.xprgroup.com 8 11. INSTALLER PROGRAMMING Set Relay 1 Time (on board) Action Swipe Installer Finger 1 time Wait 5 seconds (until fast blinking) Swipe the INSTALLER Finger and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode Finger x1 x1 x1 Backlight slow blinking fast blinking fast blinking Buzzer Sound short beep short beep beeps on 1 second short + long beep Set Relay 2 Time (remote) Action Finger Backlight Buzzer Sound Swipe Installer Finger 2 times x2 Wait 5 seconds (until fast blinking) Swipe the INSTALLER Finger and start counting seconds x1 Swipe the INSTALLER Finger to stop or wait 30 seconds to x1 put the relay in toggle mode slow blinking fast blinking fast blinking short beep short beep beeps on 1 second short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays (DINRTT and RU2). Consult the installer if Relay 2 is available in your system. BUZZER ON/OFF Action Swipe Installer Finger 3 times Wait 5 seconds (until fast blinking) Swipe Installer Finger Finger x3 x1 Backlight slow blinking fast blinking Buzzer Sound short beep short beep short + long beep BACKLIGHT ON/OFF Action Swipe Installer Finger 4 times Wait 5 seconds (until fast blinking) Swipe Installer Finger Finger x4 x1 Backlight slow blinking fast blinking Buzzer Sound short beep short beep short + long beep www.xprgroup.com 9 Installer Programming block diagram Swipe the Installer Finger 1 to 4 times depending of the desired menu www.xprgroup.com 10 www.xprgroup.com 11 This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU. www.xprgroup.com 12