IIS Windows Server
autonat.com
User Guide for WORLD EYECAM models including: TD-2700TE-HP Digital Video Recorder, TD-2700TE-HP, Digital Video Recorder, Video Recorder, Recorder
Index of /uploads
File Info : application/pdf, 2 Pages, 1.28MB
DocumentDocumentDigital Video Recorder Internet Quick Start Guide 1. Notes Please read this instruction carefully for using the product and keep it for further reference. All the examples and pictures used here are for reference only. The contents of this manual are subject to change without notice. This device should be operated only from the type of power source indicated on the marking label. The voltage of the power must be verified before using the same. 2. Packing Check Please check the device and the accessories after getting the device. If there are any damages, shortages or defects, please contact your dealer immediately. 3. HDD Installation This series of the product supports 2 SATA hard drives. Please make sure that the device is powered off before the installation. The pictures of the installation are only for reference, please take the real object as the standard. Loosen the screws to open the cover. Screw the screws into the holes of the HDD but not tighten them. Put the HDDs onto the bottom of the machine. Turn over the machine and secure the HDDs with the screws. Connect the power and data cables. Name ALARM OUT ALARM IN GND VIDEO IN CVBS AUDIO OUT AUDIO IN HDMI VGA LAN USB e-SATA RS485 DC12V Rear Panel for 16CH Description Relay output; connect to external alarm Alarm input for connecting sensor Grounding Video input CVBS Video output; connect to monitor Audio output; connect to sound box Audio input; connect to microphone or pickup Connect to high definition display device Connect to monitor Network port Connect to USB storage device or USB mouse Connect to HDD with e-SATA interface Connect to keyboard or speed dome. A is TX+,B is TXPower input 5. Startup & Shutdown Startup Connect the monitor and the power. The device will boot and the power indicator will display blue. A wizard window will pop up. Shutdown Click "Start" and then select "Shutdown" icon. This will bring up a shutdown window. The device will shut down by clicking "OK" button. Then disconnect the power. Install back the cover and secure it with the screws. Tips: Please check the inside structure of the device and make sure the cables connected well before installing the cover back. Please format the HDD before using. 4. Rear Panel Instruction The interfaces of the rear panels are for reference only. ALARM OUT ALARM IN 1 3 5 7 COM1 NO1 GND 1 3 5 7 1 3 5 7 CVBS COM2 NO2 GND 2 4 6 8 2 4 6 8 AUDIO IN 2 4 6 8 VIDEO IN AUDIO OUT Rear Panel for 8CH VGA e SATA B A LAN USB RS485 DC12V 6. Login The default username is admin and the default password is 123456. You must configure the wizard if you start the DVR for the first time and you may change the password when you configure the wizard for the first time. You can skip the settings of wizard next time. Click "Start" and select "Login". This will take you to see a login box. Input default username and password you set and you can see the live image. Username Password Login admin Enter Password Display Password Log In Automatically Edit Security Question Login Cancel 7. Analog Camera Connection First connect the camera to the DVR. Then go to Start Settings Camera Manage Camera Camera Signal to checkmark the video mode. The actual signals input shall correspond to the video mode. Please refer to User Manual for details. 8. Network Configuration & Add IP Camera After you finish adding IP cameras, you can see the live images through the monitor of the DVR. The following will mainly introduce how to add the IP cameras via LAN/WAN. LAN Set the network of the DVR. Go to Start Settings Network TCP/IP. Input IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the DVR and the router. Go to Start Settings Network Port. Input HTTP port (the default value is 80), server port (the default port is 6036). Click "Apply" to save the settings. IP Address Settings Ethernet Port 1 ( Online ) Obtain an IPv4 address automatically Address 192 . 168 . 1 . 2 Subnet Mask 0 . 0 . 0. 0 Gateway MTU 192 . 168 . 1 . 1 1500 Obatin DNS server address automatically Preferred DNS 192 . 168 . 1 . 1 Alternate DNS 0 . 0 . 0. 0 Obtain an IPv6 address automatically Address Mask Length 0 Gateway Go to Start Settings Camera Add Camera. The DVR will automatically refresh the cameras searched. The IPC which supports the Onvif protocol may be added manually. If the IPC searched is not in the same local network as the DVR, you should select the device and click to modify the IP address. Quickly Add Manually Add Add Camera No. Address 1 192.168.2.45 Port Edit 80 Subnet Mask 255.255.255.0 Protocol XXX Model XXX Version 4.0.0.1.beta1 Selected: 1/1 Remain Bandwidth: 10 / 10 Mb Mac Address Address Subnet Mask Gateway Username Password Default Password Add Cancel Edit IP CE :98 :23 :75 :35 :22 192 .168 . 1 . 45 255 . 255 . 255 . 0 192 .168 . 1 . 1 admin Sync to IPC OK Cancel Checkmark the device you want to add and then click "Add" button.The DVR will automatically refresh the cameras and return to "Edit Camera" interface. "Online" status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, ect. Camera Signal Edit Camera IP Planning Search Camera No. Camera Name Address Port Status Protocol Model Preview Edit 1 IP Camera 1 192.168.1.45 80 Online XXX 2 [A01]Camera1 XXX 3 [A02]Camera2 4 [A03]Camera3 5 [A04]Camera4 Upgrade Version 4.1.0.0 Camera Name Address Port Protocol Model Username Password Edit Camera IP Camera 1 192 .168 . 1 . 58 80 XXX XXX admin Sync to IPC Test OK Cancel WAN Set the network of the DVR. Go to Start Settings Network PPPoE. Input static IP address or enable PPPoE and then input the user name and password received from your ISP. Go to Start Settings Camera. Click "Add Camera" or behind the column of the search camera and select "Manually Add" to add the IP cameras. Input IP address, server port, username and password of the IP camera. The IP camera must be connected over WAN. And here the IP address of the IP camera must be a WAN IP address. 9. UPnP You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping. Go to Start Settings Network UPnP, and enable UPnP and then click "Apply" button to save. Enable the UPnP function in the router. Click "Refresh" button to refresh the UPnP status. If the UPnP status were still "Invalid UPnP" after refreshing it for several times, the port would be wrong. Please change the mapping type to "Manual" and then click to modify the port until the UPnP status turns to "valid UPnP". UPnP Enable Map Type Auto Port Type HTTP Port HTTPS Port Server Port RTSP Port External Port 80 443 6036 554 External Address 183.17.254.19 183.17.254.19 183.17.254.19 183.17.254.19 Port UPnP Status Edit 80 Valid UPnP 443 Valid UPnP 6036 554 Valid UPnP Invalid UPnP Refresh Apply 10. NAT NAT Settings The DVR shall be powered on and connected to the network. Go to Start Settings Network TCP/IP. You can obtain the IP address, subnet mask and gateway automatically. You can also manually enter them according to the actual network situation. Please make sure the network segment is the same as that of the network which is used. Set the preferred or alternative DNS Server. Click "Apply" to save the parameters. Go to Start Settings Network NAT tab. Enable NAT and select the NAT Server Address (The default NAT Server Address is nat.autonat.com). Click "Apply" to save the parameters. NAT Visit Address Enable www.autonat.com NAT Server Address nat.autonat.com Apply NAT Access After finishing the NAT settings, you can input www.autonat.com in the IE address bar and then press enter to go to the following interface. If you are the first time to access the NAT, you shall download and install the ActiveX according to the popup tips. After installing ActiveX successfully, it will pop the login box. Enter device serial number Enter Username Enter Password Login Device Serial Number: Click on the menu bar at the bottom of the live interface to check the serial number or go to Start Settings Network Network Status to check the serial number of the DVR). Username: The username of the DVR. The default username is admin. Password: The password of the DVR. The password is set by yourself when you configure the wizard for the first time. 11. Manual Recording Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click the recording. to check the status of 12. Playback Instant playback Click "Instant Playback" in the right-click menu of the camera's preview window to select or drag the playback progress bar to change the playback time to play back the record. General playback Click on the tool bar at the bottom of the live preview interface or click Start Playback to go to the playback interface as shown below. You can also add the playback cameras manually. Click in the playback window to pop up the "Add Camera" window. Check the cameras in the window and then click "Add" to add playback camera. The record files of the added playback camera will be played in the playback interface. 450041001147 A0