TP-Link Switch Regulatory Compliance and Safety Information

TP-Link

Product: Switch

FCC Compliance Information Statement - Class A Switch with Power Adapter

Product Name: Switch

Model Numbers: DS105GP, DS106GPP, DS106P, DS108GP, DS110GMP, DS111P, DS116GE, LS105GP, LS105LP, LS106LP, LS108GP, LS109P, LS1210GP, TL-SF1005LP, TL-SF1005P, TL-SF1006P, TL-SF1008LP, TL-SF1008P, TL-SF1009P, TL-SG1005LP, TL-SG1005P, TL-SG1006PP, TL-SG1008P, TL-SG105MPE, TL-SG105PE, TL-SG105PP-M2, TL-SG108PE, TL-SG116, TL-SG116E, TL-SG116P, TL-SG1210MP, TL-SG1210MPE, TL-SG1210P, TL-SG1210PP, TL-SG605P, TL-SG608P, TL-SL1311MP, TL-SL1311P, S4500-8G, S4500-8GP, S4500-8GP2F, S4500-16GP, SG2008, SG2008P, SG2210XMP-M2, SG2016P, SG2210P, T1500G-8T, TL-SG2008, TL-SG2008P, TL-SG2016P, TL-SG2210P, ES205GP, ES210GP

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Compliance Information Statement - Class A Switch with No Power Adapter

Product Name: Switch

Model Numbers: RP108GE, DS1008X, DS1016G, DS1018GMP, DS1024G, DS1016GE, DS1024GE, TL-SF1016, TL-SF1016DS, TL-SF1024, TL-SF1024D, TL-SF1048, TL-SG1005P-PD, TL-SG505I, TL-SG1008, TL-SG1008MP, TL-SG508I, TL-SG1016, TL-SG1016D, TL-SG1016DE, TL-SG1016PE, TL-SG1024, TL-SG1024D, TL-SG1024DE, TL-SG1024S, TL-SG1048, TL-SG1218MP, TL-SG1218MPE, TL-SG1428PE, TL-SL1218MP, TL-SL1218P, TL-SL1226P, TL-SX1008, S4500-8GHP2F, S5500-8MHP2XF, S5500-8XF, S5500-16XF, S5500-24F4XF, S5500-24GP4F, S5500-24GP4XF, S5500-24MPP4XF, S5500-48GP4F, S5500-48GP4XF, SG2005P-PD, SG2210MP, SG2218, SG2218P, SG2428P, SG3210, SG3210XHP-M2, SG3210X-M2, SG3218XP-M2, SG3428, SG3428MP, SG3428X, SG3428XF, SG3428X-M2, SG3428XMP, SG3428XMPP, SG3428XPP-M2, SG3452, SG3452P, SG3452X, SG3452XP, SG3452XMPP, SL2428P, SX3008F, SX3016F, SX3032F, SX3206HPP, SX3832, SX3832MPP, TL-SG2210MP, TL-SG2218, TL-SG2218P, TL-SG2428P, TL-SG3210, TL-SG3210XHP-M2, TL-SG3428, TL-SG3428MP, TL-SG3428X, TL-SG3428XF, TL-SG3428X-M2, TL-SG3428XMP, TL-SG3428XPP-M2, TL-SG3428X-UPS, TL-SG3452, TL-SG3452P, TL-SG3452X, TL-SG3452XP, TL-SL2428P, TL-SX3008F, TL-SX3016F, TL-SX3206HPP, SG6428X, SG6428XHP, SG6654X, SG6654XHP, SX6632YF, SG2428LP, S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF, S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y, S7500-26XF6Y, S7500-48XF4C, S7500-24Y4C

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2024/08/18

FCC Compliance Information Statement - Class B Switch with Power Adapter

Product Name: Switch

Model Numbers: DS105G, DS105G-M2, DS105X, DS108G, DS108G-M2, DS105GE, DS108GE, LS1005, LS1005G, LS1008, LS1008G, LS105G, LS108G, TL-SF1005D, TL-SF1008D, TL-SF1016D, TL-SF1024M, TL-SG1005D, TL-SG1008D, TL-SG105, TL-SG105E, TL-SG105-M2, TL-SG105S, TL-SG105S-M2, TL-SG108, TL-SG108E, TL-SG108-M2, TL-SG108S, TL-SG108S-M2, TL-SG605, TL-SG605E, TL-SG608, TL-SG608E, TL-SX105, ES205G

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2024/08/18

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

UKCA Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

CAN ICES-3 (B)/NMB-3(B)

BSMI Notice

安全諮詢及注意事項:

• 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
• 清潔本產品之前請先拔掉電源線.請勿使用液體、噴霧清潔劑或濕布進行清潔。
• 注意防潮,請勿將水或其他液體潑灑到本產品上。
• 插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。
• 請勿將本產品置放於靠近熱源的地方.除非有正常的通風,否則不可放在密閉位置中。
• 不要私自拆開機殼或自行維修,如產品有故障請與原廠或代理商聯繫。
• 為避免電磁干擾,本產品不應安裝或使用於住宅環境。

Harmful Substance Declaration

Notes: 1. "Exceeds 0.1 wt %" and "Exceeds 0.01 wt %" indicate that the percentage content of the restricted substance exceeds the reference percentage value. 2. "○" indicates that the percentage content of the restricted substance does not exceed the reference percentage value. 3. "—" indicates that the restricted substance is exempted.

Ukrainian Compliance

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Keep the device away from water, fire, humidity or hot environments.
• Place the device with its bottom surface downward.
• For switch powered by power adapter: Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Adapter shall be installed near the equipment and shall be easily accessible.
• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us.
• For switch powered by power cord: Plug the product into the wall outlets with earthing connection through the power supply cord.
• The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• For switch powered by USB or standard PoE: This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.
• In Denmark: "Apparatets stikprop skal tilsluttes en stikkontakt med jord som giver forbindelse til stikproppens jord.";
• In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" ;
• In Norway: "Apparatet må tilkoples jordet stikkontakt";
• In Sweden: "Apparaten skall anslutas till jordat uttag".
• Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the Symbols on the Product Label

Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.

Wall Mounting Requirements

For LS105GP/ LS108GP/ LS1210GP/ TL-SG105PP-M2/ TL-SG1210PP:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For DS110GMP/ DS111P/ DS116GE/ TL-SG116/ TL-SG116E/ TL-SG116P/ TL-SG1210MP/ TL-SG1210MPE/ TL-SL1311MP/ TL-SL1311P/ ES210GP:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For TL-SG105PE/ TL-SG605P:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For DS105GP/ DS106GPP/ DS106P/ DS108GP/ LS105LP/ LS106LP/ LS109P/ TL-SF1005LP/ TL-SF1005P/ TL-SF1006P/ TL-SF1008LP/ TL-SF1008P/ TL-SF1009P/ TL-SG1005LP/ TL-SG1005P/ TL-SG1006PP/ TL-SG1008P/ TL-SG105MPE/ TL-SG108PE/ TL-SG608P/ S4500-8G/ S4500-8GP/ S4500-8GP2F/ S4500-16GP/ SG2008/ SG2008P/ SG2210XMP-M2/ SG2016P/ SG2210P/ T1500G-8T/ TL-SG2008/ TL-SG2008P/ TL-SG2016P/ TL-SG2210P:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For ES205GP:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# standard and are more than 10 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.

For RP108GE:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#/5#/6# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For TL-SG505I/TL-SG508I:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#/6#/8# standard and are more than 12.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 7 mm.

For TL-SG1005D:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# standard and are more than 10 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.

For TL-SG1008D:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# standard and are more than 10 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4 mm.

For DS105G-M2/ DS105X/ DS108G-M2/ DS105GE/ DS108GE/ LS105G/ LS108G/ TL-SG105E/ TL-SG105-M2/ TL-SG105S-M2/ TL-SG108E/ TL-SG108-M2/ TL-SG108S-M2/ TL-SG605E/ TL-SG608E/ TL-SX105:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For LS1005G/ LS1008G:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 2.5 mm.

For TL-SF1016D:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 9 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 3 mm.

For DS105G/ DS108G/ TL-SG105/ TL-SG105S/ TL-SG108S/ TL-SG605:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For TL-SG108/ TL-SG608:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

For ES205G:

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# or 6# standard and are more than 11 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.