User Guide for Uascent models including: UAM087, UAM087 Matter Cost Effective WiFi Plus BLE Module, Matter Cost Effective WiFi Plus BLE Module, Cost Effective WiFi Plus BLE Module, WiFi Plus BLE Module, BLE Module, Module
Shenzhen Uascent Technology Co.,Ltd JX-UAM08 UAM087 2A68EJX-UAM08 2A68EJXUAM08 jx uam08
Shenzhen Uascent Technology Co.,Ltd JX-UAM08 UAM08 2A68EJX-UAM08 2A68EJXUAM08 jx uam08
Shenzhen Uascent Technology Co., Ltd Universal Ascent Holdings Limited UAM087-Matter Wi-Fi Single-band 1T1R 802.11b/g/n Module Datasheet Office: 2101, Zhongxing Hotel , No. 19, Xinghua 1st Road, Xin'an Street, Bao'an District, Shenzhen, China. TEL: +86-0755-82571152 E-MAIL: marketing@uascent-iot.com Website: www.uascent-iot.com Customer Approval : Company Title Signature Date Shenzhen Uascent Technology Co., Ltd 1 www.uascent- Revision History. Version Date 1.0 2024/04/25 Revision Content New version UAM087-Matter Draft Bella Approved Shenzhen Uascent Technology Co., Ltd 2 www.uascent- UAM087-Matter CONTENTS 1 Overview.................................................................................................................................................4 1.1 Introduction ..........................................................................................................................................4 1.2 Features ...............................................................................................................................................4 1.3 Recommended Operating Rating.....................................................................................................4 1.4 Reference power consumption for conventional continuous operation .....................................4 1.5 Low-power consumption ....................................................................................................................5 1.6 ESD Specifications .............................................................................................................................5 2 Module use precautions.....................................................................................................................5 3 WiFi Specification ................................................................................................................................5 4 Bluetooth Specification......................................................................................................................6 5 Pin Descriptions ...................................................................................................................................6 5.1 Pin Outline............................................................................................................................................6 5.2 Pin Definition........................................................................................................................................6 6 Dimensions............................................................................................................................................7 6.1 Module Picture.....................................................................................................................................7 6.2 Module Mechanical Dimensions.......................................................................................................8 7 Antenna Information ...........................................................................................................................9 7.1 Antenna type........................................................................................................................................9 7.2 Module layout considerations............................................................................................................9 8 Environmental Requirements ...........................................................................................................9 8.1 Recommended Reflow Profile. .........................................................................................................9 8.2 Note .....................................................................................................................................................10 8.3 Humidity sensitive control ................................................................................................................11 9 Package. ...............................................................................................................................................12 9.1 Packaging Detail ...............................................................................................................................12 10 Transport regulations. ....................................................................................................................12 11 Disclaimer and copyright notice..................................................................................................12 12 Attention.............................................................................................................................................13 Shenzhen Uascent Technology Co., Ltd 3 www.uascent- 1 Overview. UAM087-Matter 1.1 Introduction. UAM087 is a cost-effective WIFI+BLE module developed by Uascent Technology, supporting Bluetooth dual mode 5.2 and IEEE 802.11 b/g/n protocol standards, lightweight TCP/IP protocol stack, STA, AP, and Direct modes, and Matter protocol. Users can use this module to add networking functions to existing devices or build independent network controllers. 1.2 Features. Supports 20 MHz channel. Standard IEEE 802.11b/g/n. Support WiFi+Bluetooth 5.2. Support STBC. Built-in low-power 32-bit MCU speed up to 160MHz, can be used as an application processor. Support STA and AP and Direct working modes. Support BLE 1 Mbps. 1.3 Recommended Operating Rating. Description Ambient Temperature (TA) (VOL) (VOH) Vcc Output low voltage Output high voltage Min -40 3.0 VSS VCC-0.3 Typ 25 3.3 Max 85 3.6 VSS+0.3 VCC Unit deg.C V V V 1.4 Reference power consumption for conventional continuous operation. Parameter IRF IRF IRF IRF IRF IRF Condition / Notes TX Mode 11b 11M 11g 54M 11n HT20 MCS7 RX Mode 11b 11M 11g 54M 11n HT20 MCS7 Typ. 270 240 230 80 80 80 Unit mA mA mA mA mA mA Uascent Technology Co., 4 www.uascent- 1.5 Low-power consumption Parameter DTIM 1 10 DTIM 1 5 Condition / Notes 260 370 UAM087-Matter Test time 1 min 1 min Unit uA uA 1.6 ESD Specifications Item Human Body Mode (HBM) CDM Description Electrostatic Discharge Tolerance under Human Body Model Electrostatic Discharge Tolerance under Charged Device Model Value ±2 ±0.5 Unit KV KV 2 Module use precautions. When using the WIFI module of Uascent Technology, a certain tolerance should be reserved for the output current of the power supply. It is recommended that the output current of the power supply be 500mA, and a suitable power supply IC packaging should be selected. When using LDO power, attention should be paid to the issue of thermal, and when using DC-DC power, attention should be paid to the issue of overshoot at the moment of power on. 3 WiFi Specification. Features Main Chipset Operating Frequency Operating Voltage WIFI Standard PHY Data rates Descriptions BEKEN BK7238 2.4122.462GHz 3.0~3.6V IEE 802.11b/g/n Wi-Fi: 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps HT20 MCS0-MCS7 Transmit Output Power EVM Receiver Sensitivity Uascent Technology Co., Wi-Fi: 802.11b@11Mbps 16±2dBm 802.11g@54Mbps 15±2dBm 802.11n@HT20 MCS7 14±2dBm 802.11b /11Mbps: EVM-10dB 802.11g /54Mbps: EVM-25dB 802.11n /HT20 MCS7: EVM-27dB 802.11b@8% PER11Mbps -88dBm 5 www.uascent- (HT20) Operating Channel Antenna 802.11g@10% PER 54Mbps-74dBm UAM087-Matter 802.11n@10% PER MCS 7 -71dBm Wi-Fi 2.4GHz: 11: (Ch. 1-11) United States(North America) 13: (Ch. 1-13) Europe 14: (Ch. 1-14) Japan PCB onboard antenna 4 Bluetooth Specification. Features Operating Frequency BLE version Data rate Tx output power Rx sensitivity (PER 1500 packet data 30.8%) Descriptions 2.4022.480GHz 5.1 Typical : 1Mbps 20dBm(Max) -93dBm 5 Pin Descriptions. 5.1 Pin Outline. <TOP> 5.2 Pin Definition. <BOT> Pin No. Name 1 P14 2 P16 Type I/O I/O Description GPIO14/SPI_SCK GPIO16/SPI_MOSI Uascent Technology Co., 6 Voltage www.uascent- 3 P28 I/O 4 P22 I/O 5 P20 I/O 6 RX2 I/O 7 TX2 I/O 8 P24 I/O 9 P26 I/O 10 P6 I/O 11 P07 I/O 12 P8 I/O 13 GND P 14 3V3 P 15 TX1 I/O 16 RX1 I/O 17 P23 I/O 18 CEN I/O 19 P9 I/O 20 P17 I/O 21 P15 I/O P:POWER I:INPUT 6 Dimensions. 6.1 Module Picture. GPIO28/ADC4 UAM087-Matter GPIO22 GPIO20/ADC3 GPIO1/UART_RX2/ADC5 GPIO0/UART_TX2 GPIO24/PWM4/I2C_SCL/ADC2 GPIO26/PWM5/I2C_SDA/ADC1 GPIO6/CLK13M/PWM0/JTAG_TCK GPIO7/PWM1/JTAG_TMS GPIO8/PWM2/JTAG_TDI/CLK26M Ground Supply 3.3V 3.3V UART_TX1/GPIO11.Prohibit pull-up.The default state for MCU docking to the serial port needs to be configured as low level or high resistance state. UART_RX1/GPIO10.Prohibit pull-up.The default state for MCU docking to the serial port needs to be configured as low level or high resistance state. GPIO23 Reset pin GPIO9/PWM3/JTAG_TDO GPIO17/SPI_MISO/I2C_SDA GPIO15/SPI_CSN/I2C_SCL O:OUTPUT Uascent Technology Co., TOP BOTTOM 7 www.uascent- UAM087-Matter L:20.30 x W:15.80 x H:2.7 (±0.2) unit=mm 6.2 Module Mechanical Dimensions. BOTTOM (unit=mm) 6.3 PCB Layout Reference. Uascent Technology Co., (unit=mm) 8 www.uascent- 7 Antenna Information. UAM087-Matter 7.1 Antenna type. This module antenna type is PCB on-board antenna with antenna gain of -1.3dBi (MAX) 7.2 Module layout considerations. The UAM087-A0 module shall be welded to the PCB board. In order to obtain the best RF performance. Under the PCB on-board antenna, there should be no copper laying, device and wiring. During PCB design, the corresponding area should be cleared. As shown in the following figure. 8 Environmental Requirements. 8.1 Recommended Reflow Profile. Referred to IPC/JEDEC standard. Peak Temperature : <250°C Number of Times : 2 times Uascent Technology Co., 9 www.uascent- UAM087-Matter 8.2 Note. Note:Take and use the module, please insure the electrostatic protective measures. 1. Reflow soldering temperature should be according to the customer the main size of the products, such as the temperature set at 250 + 5 for the MID motherboard. About the module packaging, storage and use of matters needing attention are as follows: 2. The module of the reel and storage life of vacuum packing: 1). Shelf life: 8 months, storage environment conditions: temperature in: < 40 , relative humidity: < 90% r.h. 3. The module vacuum packing once opened, time limit of the assembly: Card:1) check the humidity display value should be less than 30% (in blue), such as: 30% ~ 40% (pink), or greater than 40% (red) the module have been moisture absorption. 2.) factory environmental temperature humidity control: -30 , 60% r.h.. 3). Once opened, the workshop the preservation of life for 168 hours. 4. Once opened, such as when not used up within 168 hours: 1). The module must be again to remove the module moisture absorption. 2). The baking temperature: 125 , 8 hours. 3). After baking, put the right amount of desiccant to seal packages. Uascent Technology Co., 10 www.uascent- 8.3 Humidity sensitive control. UAM087-Matter Uascent Technology Co., 11 www.uascent- 9 Package. UAM087-Matter 9.1 Packaging Detail. The module and the humidity indicator card are placed together in vacuum anti-static packaging, separated by a certain amount of paper, and neatly placed in the packaging box.The packaging must have reliable moisture-proof and anti-collision measures. Note1: There is a "triangular arrow" on the humidity indicator card indicating at 30%RH (as shown in the picture below). If the chemical changes to pink in the circle it points to, the element is damp and needs baking. Note2: Please confirm the packaging style with our sales staff before purchasing this product. If no packing style is specified before purchase, we will ship the goods by our own choice of packing method. 10 Transport regulations. In the process of logistics or express transportation, attention should be paid to handling with care to avoid direct rain and snow. 11 Disclaimer and copyright notice. All information in this document is provided according to the product status quo and subject to change without notice. The contents of this document disclaim any warranties, including any warranties of fitness for sale, fitness for a particular purpose or non-infringement, and any warranties mentioned elsewhere in any proposal, specification or sample. Uascent Technology Co., 12 www.uascent- UAM087-Matter This document is not liable for any infringement of patent rights arising from the use of the information contained in this document. This document does not grant any license, express or implied, to use any intellectual property rights, estoppel or otherwise. All trademarks mentioned herein are the property of their respective owners. 12 Attention. Due to product version upgrade or other reasons, the content of this manual may be changed. Shenzhen Uascent Technology Co., Ltd. reserves the right to modify the content of this manual without any notice or prompt. If users need to obtain the latest product information, please apply for the final document with our company.This manual is only used as a guide. Shenzhen Uascent Technology Co., Ltd. tries its best to provide the latest information in this manual, but does not guarantee that the content of the manual is completely accurate. None of the statements, information and recommendations contained in this manual constitute any warranty, express or implied. FCC Statements: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user's authority to operate the equipment. Important Note: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Federal Communications Commission of the U.S. Government (FCC) and the Canadian Government authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator shall be responsible for re-evaluating the end-product (including the transmitter) and obtaining a separate FCC authorization in the U.S. and Canada. OEM Integrators End Product Labeling Considerations: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: " Contains, FCC ID: 2A68EJX-UAM087". The grantee's FCC ID can be used only when all FCC compliance requirements are met. OEM Integrators End Product Manual provided to the End User: The OEM integrator shall not provide information to the end user regarding how to install or remove this RF module in end product user manual. The end user manual must include all required regulatory information and warnings as outlined in this document. Uascent Technology Co., 13 www.uascent- UAM087-Matter 2.2 List of applicable FCC rules The device compliance with FCC Part 15.247 2.3 Summarize the specific operational use conditions The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required for the installed module 2.4 Limited module procedures Device is single module approval 2.5 Trace antenna designs PCB onboard antenna, antenna gain is -1.3dBi the antenna size as below 2.6 RF exposure considerations Compliance with FCC Part 2.1091 This device is intended only for OEM integrators under the following conditions: 1.The antenna must be installed such that 20 cm is maintained between the antenna and users. 2. The transmitter module may not be co-located with any other transmitter or antenna. As long as the two conditions above are met, additional transmitter testing will not be required. 2.7 Antennas PCB onboard antenna, antenna gain is -1.3dBi. 2.8 Label and compliance information The label compliance with FCC requirement and the end product must be labeled in a visible area with the following: " Contains, FCC ID: 2A68EJX-UAM087" 2.9 Information on test modes and additional testing requirements The module under Continuous transmit ion and lager than 98% duty cycle 2.10 Additional testing, Part 15 Subpart B disclaimer The test results compliance with FCC Part 15B requirement. Uascent Technology Co., 14 www.uascent-Microsoft Word 2010 Microsoft Word 2010