User Manual for TITAN ARMY models including: P24H2P 24 Inch Computer Monitor, P24H2P, 24 Inch Computer Monitor, Computer Monitor
TITAN ARMY 24 Inch Computer Monitor, 100Hz, IPS, 1080p Full HD, Adaptive Sync, 99% sRGB, Frameless Gaming Office Monitor, VESA 75 * 75, Low Blue Light, Tilt Adjustable, HDMI, VGA, P24H2P
P24H2P
Precautions
Before using this product, please read this User Manual carefully and keep it well
Keep the monitor away from water sources or damp places, such as bath rooms, kitchens, basements and swimming pools.
Make sure the monitor is placed on a flat surface. If the monitor falls down, it may cause human injury or device damage. Store and use the monitor in a cool, dry and well ventilated place, and keep it away from emission and heat sources. Do not cover or block the vent hole in the rear casing, and do not use the product on a bed, sofa, blanket or similar objects.
The range of the supply voltage of the monitor is printed on the label on the rear casing. If it is impossible to determine the supply voltage, please consult the distributor or local power company.
If the monitor will not be used for a long period, please cut off the power supply to avoid electric shock in rainy days and damage due to abnormal supply voltage.
Please use a reliable grounded socket, Do not overload the socket, or it may cause fire or electric shock.
Do not put foreign matters into the monitor, or it may cause short circuits resulting fire or electric shock.
Do not disassemble or repair this product by self to avoid electric shock. If faults occur, please contact the after-sales service directly.
Do not pull or twist the power cable forcedly.
There is a polarizer layer (not a protective film) on the surface of the screen. Do not peel it off, or the product may be damaged and the warranty will be invalid.
Package Content
Packing list
Please check that the package of the monitor contains all parts. If any part is lost, please contact the distributor. The color and shape of parts may vary with models. Figures in this User Manual are for reference only. Cables supplied may vary with purchased products. Figures in this User Manual are for reference only.
Monitor
Base
Stand stem
1 Screws x5 cKM4x10
2 Screws x3 cKM4x14
Mount adapter
Power adapter
HDMI signal cable
Redundant screws can be used as spare screws.
User Manual
Installation
Installation of base
1.Open the carton package, take out the foam and put it flat on the table top. Keep the foam underneath the monitor before attaching the stand.
2. Take out the bracket and place it on the machine shaft and fix it with two screws.
1 Screws x2 cKM4x10
3. Take out the base, align it with the bottom of the stand, and fix it with two screws.
2 Screws x2 cKM4x14
4. After assembly, simply hold the stand with hand to stand the monitor upright.
Note: During standing of the whole monitor, do not press the liquid crystal screen with hand to avoid damage to the screen.
Installation of mount
1. Open the carton, take out the product with foam still attahed, and gently place it on a desktop or table. Remove the extra parts and the foam covering the back of the monitor.
2. Put the monitor in the lower foam cover. Take out the mount adapter and 2 KM4x10 screws and tighten the mount adapter with the screws.
1 Screws x2 cKM4x10
3. Note: Hang the assembled product on a hard wall. Do not pinch the screen with your hands during the hanging process to avoid damaging the screen.
Mount (not supplied)
Note: In order to prevent the monitor from falling when it is used on the wall, please install it properly and do safety protection. Do not place or hang any objects on the wall bracket, and the wall height should be within 2 meters.
Adjustment of monitor
Instructions
12 3 4 5 Power button: Turn on/of the monitor Exit/Left button: Enter the Input select. Return to the previous menu to the left, exit the current menu. Down button: Enter the game aiming. Move down the menu option or derease the function value. Right button: Enter the OSD menu.Dial right to selcect a submenu and enter the next menu. Up button: Enter the view mode options. Move up the menu option or increase function value.
Indicator: Steady blue light indicates that the power is on and the monitor is operating normally. Red light indicates there is no video source and no horizontal or vertical signal or low voltage is detected, and that the monitor is in standby status.Make sure your computer It is turned on and all video cables are fully plugged in and/or connected.
* The bottom interface configuration at the back of the monitor varie with products.
* Note: If the power cable or signal cable is damaged, you must replace it with special soft cables or special components purchased from the manufacture or maintenance department.
HDMI interface
Use the HDMI cable to connect the HDMI IN interface of the product to the HDMI OUT interface of a PC.
Use the HDMI-DVI cable to connect the HDMI IN interface of the product to the DVI OUT interface of a PC. (In general, PCs do not transfer video signals to the monitor through the DVI OUT interface, and it is necessary to connect a loudspeaker box additionally to play sounds of PCs.)
VGA interface
Use a VGA cable to connect the VGA interface of the product to the VGA interface of the PC.
AUDIO OUT
Connect audio outputting devices such as earphones to the AUDIO OUT interface.
DC IN
Please connect the power adapter plug to the corresponding power port of the monitor, and connect the other end to a properly grounded power o utlet.
OR
OSD menu
Menu description
The color and shape of the OSD menu of the actual computer may be slightly different from them shown in the figure. Specifications of the OSD menu may change with improvements of functions without prior notice. Press the menu button on the control panel to access the monitor menu. The detailed information of each menu can be found in the following sections. 1. Press to enter the OSD menu
2. Press or to scroll through the functions. - Highlight the features you want to set, and press to open the sub-menu. - Press or to browse the sub-menu and press to highlight the features you want to see. - Press or to highlight the options and press to confirm the settings and exit the current screen.
3. Press to return to the previous menu or exit the current menu.
* Functions of the monitor vary with models, and the functions in this manual are for reference only.
Standard
View Mode
Game
Manual Image Adjust
Movie Web Text Auto Image Adjust Horizontal Size
H./V. Posion
Fine Tune Sharpness Blue Light Fliter
Aspect Rao
Adapve-Sync Contrast/Brightness
Color Adjust
Color Temperature
Color Range
FPS1 FPS2 RTS Night Vision GAMER1 GAMER2 GAMER3
Black Stabilizaon Advanced DCR Blue Light Filter Response Time Recall
H. Posion V. Posion
4:3 5:4 16:9 16:10 On Off Contrast Brightness Bluish Warm Nave
User Color
Auto Full Range Limited Range
Red Green Blue
* Functions of the monitor vary with models, and the functions in this manual are for reference only.
Audio Adjust Input Select
Setup Menu
Volume Mute D-Sub HDMI Language Select Resoluon Noce
Informaon
OSD Timeout OSD Background Auto Power Off
Sleep
Memory Recall
On Off
////Türkçe/ P/Suomi/Italiano/Españo/Deutsch/ Français/English
Resoluon H Frequency V Frequency Pixel Clock Model Number
On Off On Off 30 Minutes 45 Minutes 60 Minutes 120 Minutes Off
Basic parameters
Product Name
Liquid Crystal Display
Product model
P24H2P
Screen Size
23.8 inches
Aspect Ratio
16:9
Viewing Angle
178°(H) / 178°(V)
Pixel pitch
0.2745(H) × 0.2745V) mm
Contrast ratio
1000:1 (TYP)
Colors Resolution
16.7M 1920x1080
Maximum refresh rate
100Hz
Power specifications
12V 2.0A The standard voltage and current may vary with countries, please refer to the label at the back of the product.
Product Dimentions Without base 542.4 × 323.1 × 38.5 mm
Normal base
With base 542.4 × 412.3 × 174.9 mm
Tilting angle
Forward titling: 5°(±2°) ; Backward tilting: 15°(±2°)
Height range
NA
Rotation angle
NA
Vertical angle
NA
Action Environmental
conditions
Storage
Temperature: 0°C~ 40°C (32°F ~ 104°F) Humidity: 10%~90% RH (non-condensing)
Temperature: -20°~ 60° (-4°F ~ 140°F) Humidity: 5%~95% RH (non-condensing)
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
"This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation."
108.007.xxxxx 24H2F-I
P24H2P 2023.8.24
140*210mm
120G80G
:
Adobe PDF library 15.00 Adobe Illustrator CC 23.0 (Windows)