BANNER SD50 LED Status Display Owner's Manual

Owner's Manual for BANNER models including: SD50, SD50 LED Status Display, LED Status Display, Status Display, Display

SD50 Status Display Product Manual

Banner Engineering Corp

BANNER SD50 Status Display

Bachofen AG | BANNER Affichage d'état SD50 - A487846 | Acheter en ligne

File Info : application/pdf, 21 Pages, 1.38MB

BANNER SD50 Status Display

SD50 Status Display Product Manual
Original Instructions p/n: 242994 Rev. A 14-Jan-25 © Banner Engineering Corp. All rights reserved.

SD50 Status Display Product Manual
Contents
Chapter 1 Features.................................................................................................................. 3
Models ........................................................................................................................................................................................................... 3
Chapter 2 Wiring...................................................................................................................... 4 Chapter 3 Pro Editor Configuration for the SD50 Pro LED Status Display ....................... 5
Discrete Control............................................................................................................................................................................................. 5 Basic I/O State ........................................................................................................................................................................................ 6 Advanced I/O State................................................................................................................................................................................. 6 I/O Block I/O State .................................................................................................................................................................................. 7
Sequence Mode ............................................................................................................................................................................................ 7 Timer Mode.................................................................................................................................................................................................... 8 Counter Mode................................................................................................................................................................................................ 8 Measure Mode............................................................................................................................................................................................... 9 Factory Reset .............................................................................................................................................................................................. 10 Display Settings........................................................................................................................................................................................... 10
Chapter 4 Specifications .......................................................................................................11
FCC Part 15 Class A for Unintentional Radiators ........................................................................................................................................ 12 Industry Canada ICES-003(A)..................................................................................................................................................................... 12 Dimensions .................................................................................................................................................................................................. 12
Chapter 5 Accessories.......................................................................................................... 13
Cordsets ...................................................................................................................................................................................................... 13 Mounting Brackets....................................................................................................................................................................................... 13
Chapter 6 Product Support and Maintenance .................................................................... 15
UTF-8 Encoding Table and Unicode Characters ......................................................................................................................................... 15 Clean with Mild Detergent and Water .......................................................................................................................................................... 19 Repairs ........................................................................................................................................................................................................ 19 Contact Us ................................................................................................................................................................................................... 20 Banner Engineering Corp Limited Warranty................................................................................................................................................ 20
© Banner Engineering Corp. All rights reserved.

SD50 Status Display Product Manual

Chapter Contents Models.................................................................................................................................................................................................................. 3

Chapter 1

Features

Provide More Status Information in the Most Helpful Locations

· Easily configurable, versatile display can be installed nearly anywhere, making it a simple yet powerful alternative to complex HMIs and other displays
· Great for displaying takt time, equipment status, assembly sequences, counts, and measurements where they are most useful
· Discrete and IO-Link models integrate into many different systems and applications, especially Banner sensing, safety, and monitoring solutions
· Quick and easy configuration--simply define the desired text and call it via discrete control or process data
· Bright white LED display and multicolored status LEDs legible from 10 meters away inform operators about exactly what is going on so they can respond quickly and accurately
· IP65-rated polycarbonate housing resists impact and condensation to provide clear communication in challenging and changing environmental conditions

Models

Model Key

Series SD

Height 50

Style P

Status Display

50 mm height

P = Pro

Display Length 300
300 = 300 mm

Display Text Color W

Control D15

W = White

D15 = Discrete 15 states

Connector(1)
QP
QP = 150 mm (6 in) PVC-jacketed cable with a 5-pin M12 male quickdisconnect connector

(1) Models with a quick-disconnect connector require a mating cordset.

14-Jan-25

page 3 of 21

SD50 Status Display Product Manual

Chapter Contents
Chapter 2

Wiring

SD50 Wiring

5-Pin Male M12 Pinout

2 4

Pinout Key and Wiring
1. Brown - Input 1 2. White - Input 3 3. Blue - DC Common 4. Black - Input 2 5. Gray - Input 4

14-Jan-25

page 4 of 21

SD50 Status Display Product Manual

Chapter Contents
Discrete Control.................................................................................................................................................................................................... 5 Sequence Mode ................................................................................................................................................................................................... 7 Timer Mode .......................................................................................................................................................................................................... 8 Counter Mode....................................................................................................................................................................................................... 8 Measure Mode ..................................................................................................................................................................................................... 9 Factory Reset ..................................................................................................................................................................................................... 10 Display Settings.................................................................................................................................................................................................. 10

Chapter 3

Pro Editor Configuration for the SD50 Pro LED Status Display

Banner's Pro Editor software offers an easy way to configure Pro Series-enabled indication, touch, and illumination devices, allowing users full control of device states and device logic modes. The easy-to-use configuration software provides a variety of tools and capabilities to solve a wide range of applications such as indicating machine status or warm-up time, indicating unique steps in an assembly process, or incorporating status information into touch buttons.
Setup any Pro Series-enabled device using the free Pro Editor software, available for download at www.bannerengineering.com/proeditor.
Discrete Control
Selecting the Discrete Control tile displays three I/O State tiles: · Basic · Advanced · I/O Block

14-Jan-25

page 5 of 21

SD50 Status Display Product Manual

Pro Editor Configuration for the SD50 Pro LED Status Display

Basic I/O State Basic four-state control. Configurations made in Basic I/O State assign one wire to one state, with the following override control:
· Pin 1 (Brown) overrides Pin 4 (Black) · Pin 2 (White) overrides Pins 1 and 4 (Brown and Black) · Pin 5 (Gray) overrides Pins 1, 2, and 4 (Brown, White, and Black)
Advanced I/O State Advanced, default I/O state, with fifteen state options for maximum configuration ability. Configurations made in Advanced I/O State assign binary wiring combinations of all valid inputs to each state. Both the indication LEDs and the display text can be programmed for each of the states.

page 6 of 21

14-Jan-25

Pro Editor Configuration for the SD50 Pro LED Status Display

SD50 Status Display Product Manual

I/O Block I/O State Three-state control for use with I/O block. Configurations made in I/O Block assign state to the black, white, and combination of black and white wires for use with the I/O blocks, for which power (brown) and common (blue) are always on for five-pin connections.

Sequence Mode
Sequence Mode allows up to sixteen states that a single input can control. A pulse on the input wire moves the SD50 to the next state.

Reset State Input Next State Input First Animation
14-Jan-25

Choose the desired input wire to restart the SD50 to the First Animation as chosen in the dropdown menu. Choose the desired input wire to move SD50 to the next state in the series until the Last Animation is reached. Choose the initial state to display as the sequence is initiated.
Continued on page 8

page 7 of 21

SD50 Status Display Product Manual

Pro Editor Configuration for the SD50 Pro LED Status Display

Last Animation

Continued from page 7 Choose the final state to include in the sequence.

Timer Mode
Set a total time and up to four thresholds. Start and stop the timer counting up or down with discrete control. Colors change across threshold values.
Timer Mode uses the SD50 as a timer, counting up or down.

Count Seconds
Direction
Reset Input Auto Restart
Bar Graph Orientation Decimal Places Display Graph Only Display Bar Graph Display Slim Bar Graph Display Level as Time Data Label Value Label Standard Settings

The total time of the timer. Up: Counts up from zero to Count Seconds. Down: Counts down from Count Seconds to zero. Enable or disable the input wire to reset the timer to the initial value. The timer loops back to the original value automatically when it reaches its final value.
Determine the starting side of the bar graph. The direction of the graph is determined by the direction of the timer. Determine the number of decimal places displayed on the Count Value. Only display the bar graph, and not the numerical Count Value. Display the bar graph across the full display. Display the bar graph as a single line of LEDs. Display the time in HH:MM:SS format without data labels. Text that displays before the Count Value. Text that displays after the Count Value to indicate the units displayed. This can be up to three characters. Reset the SD50 to predetermined settings.

Counter Mode
Set a total count and up to four thresholds. Discrete, rising edge pulses count up or down. Colors change across threshold values.
Counter Mode uses the SD50 as a counter.

page 8 of 21

14-Jan-25

Pro Editor Configuration for the SD50 Pro LED Status Display

SD50 Status Display Product Manual

Pulses
Direction Reset Input
Bar Graph Orientation Decimal Places Display Graph Only Display Bar Graph Display Slim Bar Graph Data Label Value Label Standard Settings

Determine the number of counts that are either counted up to or counted down from, depending on the chosen direction. Up: Counts from zero to Pulses. Down: Counts from Pulses to zero. Enable or disable the input wire to reset the count to the initial value.
Determine the starting side of the bar graph. The direction of the graph is determined by the direction of the timer. Determine the number of decimal places displayed on the Count Value. Only display the bar graph, and not the numerical Count Value. Display the bar graph across the full display. Display the bar graph as a single line of LEDs. Text that displays before the Count Value. Text that displays after the Count Value to indicate the units displayed. This can be up to three characters. Reset the SD50 to predetermined settings.

Measure Mode
Measure Mode uses the SD50 to display a measurement as either PWM control or PFM control.

PWM/PFM PWM/PFM Low PWM/PFM High Filter Level
14-Jan-25

PWM: Pulse-Width Modulation. PFM: Pulse-Frequency Modulation. The lowest frequency of the input range. The highest frequency of the input range. The level of filtering used to minimize the effects of noise on the output.
Continued on page 10
© Banner Engineering Corp. All rights reserved.

page 9 of 21

SD50 Status Display Product Manual

Pro Editor Configuration for the SD50 Pro LED Status Display

Hysteresis Level Output Scale Value Low Output Scale Value High
Bar Graph Orientation Decimal Places Display Graph Only Display Bar Graph Display Slim Bar Graph Display Level as Time Data Label Value Label Standard Settings

Continued from page 9 The level of lag between the measurement thresholds to minimize the flickering at switch points. The low-end value of the output translated from the input frequency. The high-end value of the output translated from the input frequency.
Determine the starting side of the bar graph. The direction of the graph is determined by the direction of the timer. Determine the number of decimal places displayed on the Count Value. Only display the bar graph, and not the numerical Count Value. Display the bar graph across the full display. Display the bar graph as a single line of LEDs. Display the time in HH:MM:SS format without data labels. Text that displays before the Count Value. Text that displays after the Count Value to indicate the units displayed. This can be up to three characters. Reset the SD50 to predetermined settings.

Factory Reset
Restore the SD50 to default settings.
Display Settings
Display Settings are a type of advanced settings that are accessible across all Applications.

Text Color Brightness Scroll Direction Scroll Speed
Scroll Mode
Connector Orientation Text Justification

Configure the primary text color as either white or black.
Control the brightness of the display text.
Scroll the display text either toward or away from the connector.
Control the speed the display text scrolls.
Auto: Scrolls if the number of characters is greater than sixteen. Off: Does not scroll the display text. On: Scrolls the display text regardless of the number of characters.
Determine the orientation of the connector when installed. The display text automatically adjusts to the correct orientation.
Control the alignment of the display text: left, right, or center.

page 10 of 21

14-Jan-25

SD50 Status Display Product Manual

Chapter Contents
FCC Part 15 Class A for Unintentional Radiators............................................................................................................................................... 12 Industry Canada ICES-003(A)............................................................................................................................................................................ 12 Dimensions......................................................................................................................................................................................................... 12

Chapter 4

Specifications

Supply Voltage 12 V DC to 30 V DC Use only with a suitable Class 2 power supply (UL) or SELV power supply (CE)
Supply Current 550 mA max. at 12 V DC 260 mA max. at 24 V DC 210 mA max. at 30 V DC
Connections 150 mm (6 in) PVC-jacketed cable with a 5-pin M12 male quick-disconnect connector Models with a quick-disconnect connector require a mating cordset Do not spray cable with high-pressure sprayer or cable damage will result
Operating Temperature 20 °C to +50 °C (4 °F to +122 °F)
Storage Temperature 40 °C to +70 °C (40 °F to +158 °F)
Environmental Rating Rated IP65 Suitable for damp locations per UL 2108
Vibration and Mechanical Shock Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 1.0 mm amplitude, 5 minutes sweep, 30 minutes dwell) Meets IEC 60068-2-27 requirements (Shock: 15G 11 ms duration, half sine wave)
Construction Black polycarbonate housing and end caps Internal silicone-encapsulated LEDs Smoky polycarbonate window

Animations

Animation

Description

Off

Light is off

Steady Color 1 is solid on at a defined intensity

Flash

Color 1 flashes at a defined speed, color intensity, and pattern (Normal, Strobe, Three Pulse, SOS, or Random)

Two Color Flash

Color 1 and Color 2 flash alternately at defined speed, color intensities, and pattern (Normal, Strobe, Three Pulse, SOS, or Random)

50/50

Color 1 and Color 2 are solid at a defined intensity

50/50 Flash

Color 1 and Color 2 flash at a defined speed, color intensity, and pattern (Normal, Strobe, Three Pulse, SOS, or Random)

Intensity Color 1 repeatedly increases and decreases intensity between Sweep 0% to 100% at defined speed and color intensity

Two Color Sweep

Color 1 and Color 2 define the end values of a line across the color gamut. The light continuously displays a color by moving along the line at the defined speed and color intensities

Required Overcurrent Protection

WARNING: Electrical connections must be made by qualified personnel in accordance with local and national
electrical codes and regulations.

Overcurrent protection is required to be provided by end product application per the supplied table.
Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.

Supply Wiring (AWG)
20
22
24

Required Overcurrent Protection (A)
5.0 3.0 1.0

Supply Wiring (AWG)
26
28
30

Required Overcurrent Protection (A)
1.0 0.8 0.5

Mounting M5 and 1/4-20 compatible end caps (not included) Clip brackets for mounting are available

14-Jan-25

page 11 of 21

SD50 Status Display Product Manual

Specifications

FCC Part 15 Class A for Unintentional Radiators
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
(Part 15.21) Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Industry Canada ICES-003(A)
This device complies with CAN ICES-3 (A)/NMB-3(A). Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and 2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la norme NMB-3(A). Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne peut pas occasionner d'interférences, et (2) il doit tolérer toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité du dispositif.
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise. The measurements provided are subject to change.

51.3 [2.02]

27.7 [1.09]

4X 5.5 [0.22]
4X 11.2 [0.44]

SD50..300..

Models

L2 L1
385.5 [15.18]

M12 x 1.0

13.8 [0.54]

20.7 [0.81]

L1 300 mm (11.81 in)

4X 5.5 [0.22]

4X 5.7 [0.22]

L2 325 mm (12.8 in)

page 12 of 21

14-Jan-25

SD50 Status Display Product Manual

Chapter Contents
Cordsets ............................................................................................................................................................................................................. 13 Mounting Brackets.............................................................................................................................................................................................. 13

Chapter 5

Accessories

Cordsets

Model
MQDEC-501SS
MQDEC-503SS MQDEC-506SS MQDEC-512SS MQDEC-515SS MQDEC-530SS MQDEC-550SS

Length

5-Pin Double-Ended M12 Female to M12 Male Cordsets

Style

Dimensions

Pinout (Male)

0.31 m (1.02 ft)

0.91 m (2.99 ft) 1.83 m (6 ft) 3.66 m (12 ft) 5 m (16.4 ft) 9 m (29.5 ft) 15 m (49.2 ft)

Male Straight/ Female Straight

40 Typ.
M12 x 1 ø 14.5
44 Typ.
M12 x 1 ø 14.5

1 = Brown 2 = White 3 = Blue

Pinout (Female)

2 1

4 = Black 5 = Gray

Mounting Brackets
LMBSD50 · Metal mounting bracket kit · Hardware included
LMBSD50MAG · Magnetic mounting bracket kit · Up to 7.26 kg (16 lb) pull · Hardware included
LMBSD50-180S · Metal mounting bracket kit with 180-degree rotation · Stainless steel · Hardware included

Ø6.5

14.5 49
20

22 Ø36
20
50

45 Ø6.4

14.5 50

14-Jan-25

page 13 of 21

SD50 Status Display Product Manual
LMBSD50-180SMAG · Magnetic mounting bracket kit with 180-degree rotation · Stainless steel · Up to 7.26 kg (16 lb) pull · Hardware included

Accessories

Ø52

page 14 of 21

14-Jan-25

SD50 Status Display Product Manual

Chapter Contents
UTF-8 Encoding Table and Unicode Characters................................................................................................................................................ 15 Clean with Mild Detergent and Water................................................................................................................................................................. 19 Repairs ............................................................................................................................................................................................................... 19 Contact Us.......................................................................................................................................................................................................... 20 Banner Engineering Corp Limited Warranty....................................................................................................................................................... 20

Chapter 6

Product Support and Maintenance

UTF-8 Encoding Table and Unicode Characters

Unicode Code Point

U+0020

U+0021

U+0022

U+0023

U+0024

U+0025

U+0026

U+0027

U+0028

(

U+0029

)

U+002A

U+002B

U+002C

U+002D

U+002E

U+002F

U+0030

U+0031

U+0032

U+0033

U+0034

U+0035

U+0036

U+0037

U+0038

U+0039

U+003A

U+003B

;

U+003C

U+003D

U+003E

Character

UTF-8 (hex.) 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e
Continued on page 16

SPACE EXCLAMATION MARK QUOTATION MARK NUMBER SIGN DOLLAR SIGN PERCENT SIGN AMPERSAND APOSTROPHE LEFT PARENTHESIS RIGHT PARENTHESIS ASTERISK PLUS SIGN COMMA HYPHEN-MINUS FULL STOP SOLIDUS DIGIT ZERO DIGIT ONE DIGIT TWO DIGIT THREE DIGIT FOUR DIGIT FIVE DIGIT SIX DIGIT SEVEN DIGIT EIGHT DIGIT NINE COLON SEMICOLON LESS-THAN SIGN EQUALS SIGN GREATER-THAN SIGN

Name

14-Jan-25

page 15 of 21

SD50 Status Display Product Manual

Unicode Code Point

U+003F

U+0040

U+0041

U+0042

U+0043

U+0044

U+0045

U+0046

U+0047

U+0048

U+0049

U+004A

U+004B

U+004C

U+004D

U+004E

U+004F

U+0050

U+0051

U+0052

U+0053

U+0054

U+0055

U+0056

U+0057

U+0058

U+0059

U+005A

U+005B

[

U+005C

U+005D

]

U+005E

U+005F

U+0060

U+0061

U+0062

U+0063

U+0064

U+0065

U+0066

U+0067

U+0068

Character

Product Support and Maintenance

Continued from page 15 UTF-8 (hex.)

Name

QUESTION MARK

COMMERCIAL AT

LATIN CAPITAL LETTER A

LATIN CAPITAL LETTER B

LATIN CAPITAL LETTER C

LATIN CAPITAL LETTER D

LATIN CAPITAL LETTER E

LATIN CAPITAL LETTER F

LATIN CAPITAL LETTER G

LATIN CAPITAL LETTER H

LATIN CAPITAL LETTER I

LATIN CAPITAL LETTER J

LATIN CAPITAL LETTER K

LATIN CAPITAL LETTER L

LATIN CAPITAL LETTER M

LATIN CAPITAL LETTER N

LATIN CAPITAL LETTER O

LATIN CAPITAL LETTER P

LATIN CAPITAL LETTER Q

LATIN CAPITAL LETTER R

LATIN CAPITAL LETTER S

LATIN CAPITAL LETTER T

LATIN CAPITAL LETTER U

LATIN CAPITAL LETTER V

LATIN CAPITAL LETTER W

LATIN CAPITAL LETTER X

LATIN CAPITAL LETTER Y

LATIN CAPITAL LETTER Z

LEFT SQUARE BRACKET

REVERSE SOLIDUS

RIGHT SQUARE BRACKET

CIRCUMFLEX ACCENT

LOW LINE

GRAVE ACCENT

LATIN SMALL LETTER A

LATIN SMALL LETTER B

LATIN SMALL LETTER C

LATIN SMALL LETTER D

LATIN SMALL LETTER E

LATIN SMALL LETTER F

LATIN SMALL LETTER G

68 Continued on page 17

LATIN SMALL LETTER H

page 16 of 21

14-Jan-25

Product Support and Maintenance

Unicode Code Point

U+0069

U+006A

U+006B

U+006C

U+006D

U+006E

U+006F

U+0070

U+0071

U+0072

U+0073

U+0074

U+0075

U+0076

U+0077

U+0078

U+0079

U+007A

U+007B

{

U+007C

U+007D

}

U+007E

U+00A0

U+00A1

U+00A2

U+00A3

U+00A4

U+00A5

U+00A6

U+00A7

U+00A8

U+00A9

U+00AA

U+00AB

U+00AC

U+00AD

U+00AE

U+00AF

U+00B0

U+00B1

U+00B2

U+00B3

Character

SD50 Status Display Product Manual

Continued from page 16 UTF-8 (hex.)

Name

LATIN SMALL LETTER I

LATIN SMALL LETTER J

LATIN SMALL LETTER K

LATIN SMALL LETTER L

LATIN SMALL LETTER M

LATIN SMALL LETTER N

LATIN SMALL LETTER O

LATIN SMALL LETTER P

LATIN SMALL LETTER Q

LATIN SMALL LETTER R

LATIN SMALL LETTER S

LATIN SMALL LETTER T

LATIN SMALL LETTER U

LATIN SMALL LETTER V

LATIN SMALL LETTER W

LATIN SMALL LETTER X

LATIN SMALL LETTER Y

LATIN SMALL LETTER Z

LEFT CURLY BRACKET

VERTICAL LINE

RIGHT CURLY BRACKET

TILDE

c2 a0

NO-BREAK SPACE

c2 a1

INVERTED EXCLAMATION MARK

c2 a2

CENT SIGN

c2 a3

POUND SIGN

c2 a4

CURRENCY SIGN

c2 a5

YEN SIGN

c2 a6

BROKEN BAR

c2 a7

SECTION SIGN

c2 a8

DIAERESIS

c2 a9

c2 aa

FEMININE ORDINAL INDICATOR

c2 ab

LEFT-POINTING DOUBLE ANGLE QUOTATION MARK

c2 ac

NOT SIGN

c2 ad

SOFT HYPHEN

c2 ae

REGISTERED SIGN

c2 af

MACRON

c2 b0

DEGREE SIGN

c2 b1

PLUS-MINUS SIGN

c2 b2

SUPERSCRIPT TWO

c2 b3 Continued on page 18

SUPERSCRIPT THREE

14-Jan-25

page 17 of 21

SD50 Status Display Product Manual

Unicode Code Point

U+00B4

U+00B5

U+00B6

U+00B7

U+00B8

U+00B9

U+00BA

U+00BB

U+00BC

U+00BD

U+00BE

U+00BF

U+00C0

U+00C1

U+00C2

U+00C3

U+00C4

U+00C5

U+00C6

U+00C7

U+00C8

U+00C9

U+00CA

U+00CB

U+00CC

U+00CD

U+00CE

U+00CF

U+00D0

U+00D1

U+00D2

U+00D3

U+00D4

U+00D5

U+00D6

U+00D7

U+00D8

U+00D9

U+00DA

U+00DB

U+00DC

U+00DD

Character

Product Support and Maintenance

Continued from page 17 UTF-8 (hex.)

Name

c2 b4

ACUTE ACCENT

c2 b5

MICRO SIGN

c2 b6

PILCROW SIGN

c2 b7

MIDDLE DOT

c2 b8

CEDILLA

c2 b9

SUPERSCRIPT ONE

c2 ba

MASCULINE ORDINAL INDICATOR

c2 bb

RIGHT-POINTING DOUBLE ANGLE QUOTATION MARK

c2 bc

VULGAR FRACTION ONE QUARTER

c2 bd

VULGAR FRACTION ONE HALF

c2 be

VULGAR FRACTION THREE QUARTERS

c2 bf

INVERTED QUESTION MARK

c3 80

LATIN CAPITAL LETTER A WITH GRAVE

c3 81

LATIN CAPITAL LETTER A WITH ACUTE

c3 82

LATIN CAPITAL LETTER A WITH CIRCUMFLEX

c3 83

LATIN CAPITAL LETTER A WITH TILDE

c3 84

LATIN CAPITAL LETTER A WITH DIAERESIS

c3 85

LATIN CAPITAL LETTER A WITH RING ABOVE

c3 86

LATIN CAPITAL LETTER AE

c3 87

LATIN CAPITAL LETTER C WITH CEDILLA

c3 88

LATIN CAPITAL LETTER E WITH GRAVE

c3 89

LATIN CAPITAL LETTER E WITH ACUTE

c3 8a

LATIN CAPITAL LETTER E WITH CIRCUMFLEX

c3 8b

LATIN CAPITAL LETTER E WITH DIAERESIS

c3 8c

LATIN CAPITAL LETTER I WITH GRAVE

c3 8d

LATIN CAPITAL LETTER I WITH ACUTE

c3 8e

LATIN CAPITAL LETTER I WITH CIRCUMFLEX

c3 8f

LATIN CAPITAL LETTER I WITH DIAERESIS

c3 90

LATIN CAPITAL LETTER ETH

c3 91

LATIN CAPITAL LETTER N WITH TILDE

c3 92

LATIN CAPITAL LETTER O WITH GRAVE

c3 93

LATIN CAPITAL LETTER O WITH ACUTE

c3 94

LATIN CAPITAL LETTER O WITH CIRCUMFLEX

c3 95

LATIN CAPITAL LETTER O WITH TILDE

c3 96

LATIN CAPITAL LETTER O WITH DIAERESIS

c3 97

MULTIPLICATION SIGN

c3 98

LATIN CAPITAL LETTER O WITH STROKE

c3 99

LATIN CAPITAL LETTER U WITH GRAVE

c3 9a

LATIN CAPITAL LETTER U WITH ACUTE

c3 9b

LATIN CAPITAL LETTER U WITH CIRCUMFLEX

c3 9c

LATIN CAPITAL LETTER U WITH DIAERESIS

c3 9d Continued on page 19

LATIN CAPITAL LETTER Y WITH ACUTE

page 18 of 21

14-Jan-25

Product Support and Maintenance

Unicode Code Point

U+00DE

U+00DF

U+00E0

U+00E1

U+00E2

U+00E3

U+00E4

U+00E5

U+00E6

U+00E7

U+00E8

U+00E9

U+00EA

U+00EB

U+00EC

U+00ED

U+00EE

U+00EF

U+00F0

U+00F1

U+00F2

U+00F3

U+00F4

U+00F5

U+00F6

U+00F7

U+00F8

U+00F9

U+00FA

U+00FB

U+00FC

U+00FD

U+00FE

U+00FF

Character

SD50 Status Display Product Manual

Continued from page 18 UTF-8 (hex.)

Name

c3 9e

LATIN CAPITAL LETTER THORN

c3 9f

LATIN SMALL LETTER SHARP S

c3 a0

LATIN SMALL LETTER A WITH GRAVE

c3 a1

LATIN SMALL LETTER A WITH ACUTE

c3 a2

LATIN SMALL LETTER A WITH CIRCUMFLEX

c3 a3

LATIN SMALL LETTER A WITH TILDE

c3 a4

LATIN SMALL LETTER A WITH DIAERESIS

c3 a5

LATIN SMALL LETTER A WITH RING ABOVE

c3 a6

LATIN SMALL LETTER AE

c3 a7

LATIN SMALL LETTER C WITH CEDILLA

c3 a8

LATIN SMALL LETTER E WITH GRAVE

c3 a9

LATIN SMALL LETTER E WITH ACUTE

c3 aa

LATIN SMALL LETTER E WITH CIRCUMFLEX

c3 ab

LATIN SMALL LETTER E WITH DIAERESIS

c3 ac

LATIN SMALL LETTER I WITH GRAVE

c3 ad

LATIN SMALL LETTER I WITH ACUTE

c3 ae

LATIN SMALL LETTER I WITH CIRCUMFLEX

c3 af

LATIN SMALL LETTER I WITH DIAERESIS

c3 b0

LATIN SMALL LETTER ETH

c3 b1

LATIN SMALL LETTER N WITH TILDE

c3 b2

LATIN SMALL LETTER O WITH GRAVE

c3 b3

LATIN SMALL LETTER O WITH ACUTE

c3 b4

LATIN SMALL LETTER O WITH CIRCUMFLEX

c3 b5

LATIN SMALL LETTER O WITH TILDE

c3 b6

LATIN SMALL LETTER O WITH DIAERESIS

c3 b7

DIVISION SIGN

c3 b8

LATIN SMALL LETTER O WITH STROKE

c3 b9

LATIN SMALL LETTER U WITH GRAVE

c3 ba

LATIN SMALL LETTER U WITH ACUTE

c3 bb

LATIN SMALL LETTER U WITH CIRCUMFLEX

c3 bc

LATIN SMALL LETTER U WITH DIAERESIS

c3 bd

LATIN SMALL LETTER Y WITH ACUTE

c3 be

LATIN SMALL LETTER THORN

c3 bf

LATIN SMALL LETTER Y WITH DIAERESIS

Clean with Mild Detergent and Water
Wipe down the enclosure and the display with a soft cloth that has been dampened with a mild detergent and warm water solution.
Repairs
Contact Banner Engineering for troubleshooting of this device. Do not attempt any repairs to this Banner device; it contains no field-replaceable parts or components. If the device, device part, or device component is determined to be defective by a Banner Applications Engineer, they will advise you of Banner's RMA (Return Merchandise Authorization) procedure.

14-Jan-25

page 19 of 21

SD50 Status Display Product Manual

Product Support and Maintenance

IMPORTANT: If instructed to return the device, pack it with care. Damage that occurs in return shipping is not covered by warranty.

Contact Us
Banner Engineering Corp. headquarters is located at: 9714 Tenth Avenue North | Plymouth, MN 55441, USA | Phone: + 1 888 373 6767
For worldwide locations and local representatives, visit www.bannerengineering.com.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.

page 20 of 21

14-Jan-25

SD50 Status Display Product Manual

Banner Engineering Corp

BANNER SD50 Status Display

References