intercoax.com
User Guide for INTERCOAX models including: 1745982125, RTP-2601T RTP-2601R Transmitter Receiver, RTP-2601T RTP-2601R, Transmitter Receiver, Transmitter, Receiver
File Info : application/pdf, 2 Pages, 312.75KB
DocumentDocumentQuick Start Guide ETP-2601T / ETP-2601R Please read carefully the instruction manual before use. Contents of this manual are subject to change without prior notice for reasons such as functionality enhancements. Rev.1.3 Package ETP-2601T (Transmitter) ETP-2601R (Receiver) Terminal Connector Bracket Quick Start Guide Right Hardware Overview 57V DC Bracket Hole DDCCPower Jack PPooEEOONN//OOFFFFSwitch (ETP-2601T only) PoE-ON (ETP-2601T) PD-AUX (ETP-2601R) Left Bracket Hole RJ45 JoJoininButton Status LED Indicator LED Indicators Indicator PoE-ON (Tx) PD-AUX (Rx) Data-Link Join-Link Power Color Function ON : PoE Switch On (PoE Output) OFF : PoE Switch Off ON : PoE Input or Powered by Transmitter OFF : Powered by adapter Blinking : Ethernet Data Act ETP-Product Link 57V DC Link Overview This devices are High-Speed, long distance Ethernet & PoE extender that makes possible to transmit the Ethernet signal and PoE via 2-Wire cable (Twisted pair cable, COM, Power line) in different situations. It is cost-effective and time saving solution to migrate existing analog system to IP based system since this device supports easy installation utilizing the existing cable. With long distance transmission feature, the device makes to overcome 100 meters distance limitation easily and reduces the construction cost significantly compared with fiber optic configuration. Features Ethernet over 2-Wire communication following IEEE1901 Standard Data + Power over 2-Wire cable (UTP, COM, Power Line, etc.) Supports long distance Untwisted/Twisted 2-Wire cables Data distance up to 600m PoE distance up to 300m Max. 95Mbps Bandwidth (270Mbps between Intercoax 2 series models) 10/100 Full Duplex 128bit AES network encryption Supports Multi-connection (Daisy chain, Star, etc.) PoE, PoE+, Extra PoE (Max. 60W output) (ETP-2601T only) PoE ON/OFF Switch (ETP-2601T only) LED Indication (Data, Power, Link, PoE) Plug & Play Surge Protection Support PoE+ Input (25.5W) from PSE devices ETP-2601R Only Wire Range 28~16AWG / 0.5~1.5 Slim design Installation Guide 1. Set the IP address on the camera following the instruction manual of the camera. Î If the camera IP is automatically assigned (DHCP, etc.), there is no need to set the camera IP separately. 2. Fix the enclosed terminal block to the transmitter and receiver, then connect the 2-wire cable to the transmitter and receiver. Î Be sure to connect polarity( , ) carefully. If the connection is reversed, it will not work. 3. Connect 57V DC power to Transmitter/Receiver first and then to AC outlet. Î Receiver can be powered by PoE Switch Device (PoE+ PD Supported) but for safe working, it recommeded to use 57V DC Power supply on Receiver. When using both PoE switch Device and power supply at the same time, power supply works preferentially. Î In case of 7W camera, one 57V DC power can supply up to 300m of UTP 2-Wire. PoE transmission distance can be varied depending on cable type and Camera's power consumption(W). 4. When they are connected without any problem, Power / Join Link LED are on. 5. Adhere the brackets in the package to Transmitter/Receiver and then fix up the products. 6. Connect the UTP(LAN) cable between Receiver and NVR first and then between Transmitter and camera. 7. Turn on the PoE switch on Transmitter for PoE IP camera and if the camera is powered by a separate power source (not powered by PoE output feature of the Transmitter), turn off the PoE switch on Transmitter. Î Both Transmitter/Receiver send data and power together via 2-Wire connector. Receiver does not have PoE support so that it can send data only via RJ45. 8. Ping test is recommended to confirm the whole network after installation. 9. Check the video signal on the monitor. Applications PoE Camera 10/100 Ethernet PoE ETP-2601T 2-Wire Cable 57V DC/1.2A ETP-2601R Power Supply NVR PoE Switch 10/100 Ethernet Non-PoE IP Camera AC/DC Adapter(12V) ETP-2601T 2-Wire Cable ETP-2601R How to change the communication password (Coax/UTP/2-Wire) All Intercoax EoC converters have the same password as factory defaults setting value and can be used immediately when connecting to the product (Plug & Play mode). However, if a number of products are mixed in the same area or the signal transmission line is in poor condition, the communication passwords for each equipment (or group) can be set differently to prevent cross-talk between the lines. 1. Needed items for Joining EoC Converters / Power supply / Short Cable (Coax, UTP, 2-Wire) / Paper clip 2. Product configuration a. Connect EoC Converters with Coax cable (or UTP, 2-Wire) and power to the one of the converters up with power supply. b. Check if the Power LED on both devices is ON. 3. Remove the existing password (Unjoining) This process removes passwords that are entered as factory defaults. a. Press the Join button on one of the connected products using a paper clip until the Power LED turns off and on (Approximately 15 seconds) b. Remove the existing password by pressing the Join button on the opposite product in the same way as above. c. Join LED will be turned off if the password on the devices is removed correctly. 4. Create New Password (Joining) New password for communication between connected devices is created and this will block the communication with other devices (or group) which have a different password. a. Press the Join button for 2 seconds on one of the connected product using a paper clip and the Join LED of the device will flicker at a constant speed. (Stand-by mode) b. Press the Join button for 2 seconds on the opposite device in the same way as above. And then, the Join LED of the device flickers at a constant speed and both devices restart at the same time. c. Then the Join-Link lights up and communications are resumed between the products 5. When adding new products in 1:N configuration to a group that has already been joined. (Group Joining) a. Connect new device to the group which is already joined. (using T-BNC or Y-UTP coupler, Terminal block) b. Remove the password of the new device in the same way as step `3-a'. c. Press Join button on the one of the device of the existing group for 2 seconds and Join LED flickers at a constant speed. d. Press Join button on the new device for 2 seconds and new device restarts e. Join-Link lights up and communications are resumed between the products. Specification Model Interface 2-Wire Ethernet Transmission Rate Transmission Distance 2-Wire PoE (PoC) ETP-2601T ETP-2601R 1 x 2-Pin Terminal Block (28~16AWG or 0.5~1.5) Ethernet over 2-Wire (T-LinX) 1 x RJ45 - 10/100 Base-T with Auto-detect MDIX 95Mbps Full Duplex (270Mbps between Intercoax 2 series models) up to 600 m(Twisted Pair Cable/Cat.5e) up to 300 m (Cat.5e / 7W camera) Ethernet LED Data over 2-Wire Indication Power PoE Output Encryption Input Power PoE Output 1 x Data-Link (Yellow) 1 x Join-Link (Green) 1 x Power On (Amber) 1 x PoE Out (Red) 128-bit AES T-Linx or DC12V~57V PoE Switch or DC48V~57V IEEE802.3af(PoE), IEEE802.3at (PoE+), Extra PoE up to 60W PoE Not Supported Power Over 2-Wire Only PoE Input Not Supported Up to 25.5W (PD) Mechanical Dimension Weight Operating Temp Environment Storage Temp Relative Humidity Certification Compliance Surge Protection Optional Accessories 80.4(L) x 61.6(W) x 24(H)mm 102g -20 ~ 60°C -30 ~ 80°C 10% ~ 90% FCC, CE, KC, RoHS IEC 61000-4-5 4kV(1.2 / 50us), 2kA(8 / 20us) 57VDC / 1.2A External Power Supply Caution Please install the device following the installation guide. Do not touch the device and cable with wet hands. Keep away from moisture and shock. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that produce heat. Indoor use only. Do not use for other purposes. Do not disassemble or modify this device. Do not put any sticker or paint on it. If this device is defective or malfunctioning, please unplug the power adapter immediately and contact dealer or service center. Please use the rated power supply for the product. Connect DC power to this device first and then to AC outlet. Warranty This device has passed the quality control and product inspection. Please install and use according to the installation guide. The warranty period for this product is 24 months from the date of purchase. If this device is defective or malfunctioning, please unplug the power adapter immediately and contact dealer or service center. Any damages or breakage from user's abuse, accident, modification or natural disasters will not be covered manufacturer's warranty. Please visit below website for more detailed information. Web: http://www.intercoax.com Tel: +82. 31. 365. 3133~4 E-mail: info@intercoax.com Fax: +82. 31. 365. 3135 This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation © Intercoax Co., Ltd.