Prior to Unpacking
- Overall package weighs about 100 pounds! Two people are required to carefully unpack the product to avoid personal injuries or accidental damage to the item.
- Each item is carefully packed in customized foam. However, violent handling and shipping might crack the item. Observe potential damage while unpacking.
- The seat cover might not be hinged firmly with the toilet base. DO NOT lift the toilet by grabbing the separate seat.
[Team Lift] [Fragile]
Prior to Installation
- Inspect the toilet to ensure no damages during transit.
- Observe all plumbing and building codes in accordance with your state and local requirements.
- All dimensions are nominal. Actual size of item received might vary by up to 1/8 inch. Make sure to measure your toilet before installation.
- The step-by-step guide in the installation instructions is for general reference only. Should there be any discrepancies, Eridanus cannot be held liable. It is recommended that all Eridanus products be installed by a licensed professional.
- Read installation and maintenance instructions and user manual thoroughly before installing. Be sure to use proper tools and always wear proper personal safety equipment.
- Two people are required to handle and install the toilet to avoid personal injuries or accidental damage to the item.
- Diagrams are for general display and do not represent a specific model.
- Make sure water pressure meets the minimum requirement for your model.
- This appliance must be grounded. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter(GFCI) or Residual Current Device(RCD).
Checklist
What's in the box
- Smart Toilet
- Angle Valve
- Adapter
- Wax Ring Gasket
- Flange
- Mounting Bolts
- Remote Control
- Toddler Seat
- Supply Line/Hose
- Battery Box
- User Manual
- Installation Guide
Extra Parts/Tools Required
- Safety Glass
- Tape Measure
- Screwdriver
- Adjustable Wrench
- Putty Scraper
- Pencil/Marker
- Caulk
- AAA Battery x2
- 9V Battery
Diagram illustrating plumbing connections and rough-in dimensions for a toilet installation, showing an angle valve, floor flange, and socket with specific measurements (e.g., 6", 9 3/4", 10", 11", 12").
A visual representation of the contents of the box, including the smart toilet, angle valve, adapter, wax ring gasket, flange, mounting bolts, remote control, toddler seat, supply line/hose, battery box, user manual, and installation guide.
A collection of tools and supplies needed for installation, such as safety glasses, tape measure, screwdriver, adjustable wrench, putty scraper, pencil/marker, caulk, AAA batteries, and a 9V battery.
Installation
Install Closet Flange & Bolts
- Inspect existing closet flange. Replace it if necessary.
[Reminder] When replacing the flange, always remember to lock the nuts into position to prevent the toilet from shifting over time and damaging the wax seal.
Diagrams showing a closet flange with bolts and nuts, illustrating how to secure it.
Remove Bidet Assembly
- Unscrew the two screws located on the bidet, disconnect the hose and wire, and then remove the bidet.
A sequence of three diagrams showing the process of removing the bidet assembly, involving unscrewing screws, disconnecting a hose, and disconnecting a wire.
Apply Wax Gasket and Sealant
- With assistance, carefully turn the toilet on its side.
- Attach the wax ring gasket evenly around the rear of the trapway.
- Apply a thin bead of sealant around the toilet base.
[Reminder] Consider placing a tarp over the floor for surface protection.
A diagram showing the toilet turned on its side, with a wax ring gasket being applied to the trapway and sealant around the base.
Install Toilet Bowl
- Gently lower the toilet bowl over the floor flange ensuring that the closet bolts extend through the pre-drilled holes.
- Align the toilet squarely against the wall, then firmly press down on the wax ring and flange to establish a waterproof seal. Tighten the washers and nuts alternately until the toilet is securely positioned on the floor.
[Reminder] Avoid over-tightening as it could potentially cause the ceramics to crack.
- Apply a smooth layer of sealant around the base. Remove any excess sealant.
A sequence of three diagrams illustrating the installation of the toilet bowl onto the floor flange, showing the bolts passing through holes, alignment against the wall, and tightening of nuts.
Reinstall Bidet Assembly
- Put the bidet in position on the toilet bowl. Reconnect the hose and wire.
- Securely fasten the bidet to the toilet bowl by tightening the two screws.
Two diagrams showing the bidet assembly being placed back onto the toilet bowl and secured with screws.
Check for Leaks and Flush Function
- Connect the supply line/hose to the angle valve.
- Insert the toilet's plug into the power outlet/socket.
- Flush test. Make sure there is no leak from the waterline or the flange.
- Refer to the user manual to check if the smart toilet is operating properly.
