Philips Universal Remote Control

Model Numbers: SRP2014C/27, SRP9243B/27, SRP4222P/27

Setup

Your universal remote requires two (2) AAA batteries (not included). Alkaline batteries are recommended.

Battery Installation

Press downward on the battery cover latch and lift to remove.
Insert the batteries, making sure to match the (+) (-) polarity inside the compartment.
Replace cover and snap the latch into place.

Note: If your remote stops operating properly, replace the batteries with new ones.

Battery Precautions

Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are held down for more than 8 seconds. This saves battery life if your remote gets stuck in a place where the buttons remain depressed (e.g., between sofa cushions).

Code Saver

You have up to 10 minutes to change the batteries in your remote without losing the codes you have programmed.

Button Functions

A detailed diagram shows the functions of each button on the remote control. Key buttons include:

1. Power: Turns devices ON/OFF
2. TV, STR, DVD, AUD: Select the device to control
3. Navigation (Up/Down/Left/Right): Menu navigation
4. Last Channel: Returns to the previously selected channel
5. Setup: Used to program the remote
6. Channel Up/Down
7. Home/Guide: Access streaming device features or Guide for cable/satellite receivers
8. Info/Options: Displays on-screen show/content information
9. Menu: Displays the on-screen menu
10. Media Controls: Record, play, stop, rewind, fast forward, pause
11. Numbers: For direct channel selection
12. Dash (-): Use to select digital channels, e.g., 4.1
13. Enter: For devices that require Enter to be pressed after channel selection
14. ABCD: Access additional features for DVRs, cable and satellite receivers
15. DVD/Blu-ray™ Open/Close: Open/close a DVD/Blu-ray™ player or List features on cable/satellite receivers
16. Exit: Exit on-screen menus
17. Streaming App Hotkey: Preprogrammed to access your smart TV or streaming device's top streaming app, such as Netflix, Hulu or Amazon Prime
18. Volume Up (+)/Down (-): Controls audio volume
19. Mute: Mutes sound
20. OK: Selects menu items for the controlled device
21. Input: Selects video inputs

Direct Code Entry

Direct code entry is recommended for quick and easy programming.

Note: The TV device button is preprogrammed for Samsung TVs, and the STR device button is preprogrammed for Roku boxes.

In the Code List included with the remote, circle the 4-digit codes for the type and brand of device you wish to control.
Press and hold down the SETUP button until the remote's red light turns on. Release the SETUP button. The red light will remain on.
Press and release the chosen device button (TV, STR, DVD or AUD). The red light will blink once and remain on.
Enter the first 4-digit code circled in Step 1. The red light will turn off.
Point the remote at the device and test the buttons. If they don't work as expected, repeat Steps 2-5 with the next circled code.
Repeat the process for each device you wish to control.

Programming notes:

Some codes may operate only a few device functions, so test other codes for more functionality.
Trouble finding a code? Program the remote using the auto code search method.
For combination devices, such as a TV/DVD combo or TV/VCR combo, you may have to enter a code for each device.
Keep your device codes for future reference.

Auto Code Search

Auto code search cycles through all codes in the remote to find one for your device. Before you begin, read through the steps below to familiarize yourself with the auto code search process.

Manually turn on the device you wish to control. (Use the direct code entry method for devices without ON/OFF capability).
Press and hold down the SETUP button until the remote's red light turns on. Release the SETUP button. The red light will remain on.
Press and release the chosen device button (TV, STR or AUD). The red light will blink once and remain on.
Point the remote at the device, then press and release the POWER button. The red light will blink and then remain on after cycling through 10 codes.
Did the device turn off?
- YES: Go to Step 5.
- NO: Repeat Step 4 to test the next 10 codes.
Manually turn on the device.
Point the remote at the device, then press and release VOL+. The red light will blink once and remain on.
Did the device turn off?
- YES: Press and release the same device button pressed in Step 3. This stores the code in the remote. Go to Step 7.
- NO: Repeat Step 6 until the device turns off. Wait 3 seconds between each VOL+ button press.
Use the remote to turn on the device. Test the remote's buttons. If they don't work as expected, repeat Steps 2-7.
Repeat the process for each device you wish to control.

Code Identification

Code identification lets you retrieve the 4-digit code used to program each of your device buttons.

Press and hold down the SETUP button until the red light turns on. Then, release it. The red light will remain on.
Press and release the device button for the code you seek.
Press and release ENTER.
Press and release #1 and count how many times the red light blinks. This is the first digit in your code. Repeat the process by pressing #2, #3 and #4 for the remaining digits.
Press and release ENTER to exit this mode.

Primary Audio Control

Primary audio control lets you select an audio device to control the volume no matter which component you're operating.

Enabling Primary Audio Control

Press and hold the SETUP button until the red light remains on, then release it. The red light will remain on.
Press and release the device button for the audio component you wish to use.
Press and release the MUTE button.
Press and release VOL+. The red light will blink twice and turn off.

Disabling Primary Audio Control

Press and hold the SETUP button until the red light remains on, then release it. The red light will remain on.
Press and release the device button previously programmed for primary audio control.
Press and release the MUTE button.
Press and release VOL-. The red light will blink twice and turn off.

Troubleshooting

Remote does not operate your device

Make sure the batteries are fresh and installed correctly.
Aim the remote directly at your device and make sure there are no obstructions between the remote and the device.
Make sure you select the appropriate device on the remote you wish to control (TV for TV, STR for streaming media player, AUD for audio, etc.).
Try programming the remote with a different code. See Direct Code Entry section.
Remote may not be compatible with your device.

Remote does not operate some features of your device

Sometimes a particular code might operate a few features but not all. Try programming the remote with a different code from the Code List. See Direct Code Entry section.
Remote may not be able to operate all features of your device or button names may be different than that of your original remotes.

Reset to Factory Settings

Press and hold the SETUP button until the red light stays on, then release it. The red light will remain on.
Press and release the MUTE button.
Press and release 0 (zero). The red light will blink twice.

Combo Devices

Some combo devices (e.g., TV/VCR, DVD/VCR, etc.) require the use of a separate mode button for each part of the combo device. For example, if you have a TV/DVD combo, you might need to set up a TV code under the TV button and a separate DVD code under the DVD button to control each component.

Thank you for your purchase!

Product instructions made easy

Scan to watch a step-by-step instructional video or visit byjasco.com/40599i

Register your Philips product

Get exclusive, web-only deals and more! Scan here or visit byjasco.com/deals

Like our product? Need more remote control devices?

For additional Philips remote controls, visit our website! byjasco.com/remotes

Leave a review on your favorite retailer website or amazon.com

Having problems?

Let us know how we can help. Call 1-844-816-0320 between 7AM-8PM, M-F, Central Time.

	Philips Universal Remote Control Setup and Operation Guide A comprehensive guide to setting up and operating the Philips Universal Remote Control, including button functions, code entry, auto code search, code identification, and primary audio control.
	Philips SRP9263C/27 Universal Remote Control User Manual Comprehensive user manual for the Philips SRP9263C/27 Universal Remote Control, detailing setup, button functions, programming methods (Direct Code Entry, Auto Code Search), using features like Primary Audio Control, troubleshooting, warranty information, and FCC compliance.
	Philips SRP4040 Replacement Remote User Manual User manual for the Philips SRP4040 Replacement Remote Control, providing instructions on setup, code selection, auto IR code search, code learning, and troubleshooting for Panasonic TVs.
	Philips SRP9232D/27 Universal Remote Control User Manual This user manual provides comprehensive instructions for setting up, programming, and using the Philips SRP9232D/27 Universal Remote Control to operate various audio/video devices.
	Philips SRP4050 Replacement Remote User Manual for Hisense TVs User manual for the Philips SRP4050 replacement remote control, designed for Hisense TVs. Includes setup, code selection, auto search, code learning, disposal, and troubleshooting.
	Philips SRP43195/27 Universal Remote Control User Manual Comprehensive user manual for the Philips SRP43195/27 Universal Replacement Remote Control. Learn about setup, button functions, programming methods (Direct Code Entry and Auto Code Search), controlling combo devices, primary audio control, code identification, factory reset, troubleshooting, and warranty information.
	Philips Universal Remote Control SRP2024A/27 User Manual Comprehensive user manual for the Philips SRP2024A/27 universal remote control, covering setup, button functions, programming, troubleshooting, and warranty information.
	Philips SRP9232D/27 Universal Remote Control User Manual This user manual provides instructions for setting up, programming, and using the Philips SRP9232D/27 Universal Remote Control to operate various audio/video devices.