Instruction Manual for b d models including: 12-100 Series Structural Fixing Detail for Shutter Openings, 12-100 Series, Structural Fixing Detail for Shutter Openings, Fixing Detail for Shutter Openings, Shutter Openings
6,8,10 & 12/100 Series Structural fixing detail for shutter openings Please follow diagram for correct installation of shutters up to: 6800mm high x 7000mm wide A1/A2 G B CEILING E · Fixing (shown shaded) steel. · Material for wind rated doors MUST comply with the DTC drawings, which can be found on the B&D website. · Depending on door size and weight, steel will be required. All masonry must be solid bricks or core filled. Steel must be of a suitable thickness. If unsure consult with your engineer or B&D representative. · If floor rebate is required it must extend at least 100mm more than the opening on each side and back from the fixing face at least 100mm. OPENING HEIGHT C B A1/A2 OPENING D F FLOOR REBATE SOLID RETURN installation Spring Balanced Springless Direct Drive Springless Direct Lift Chain Drive height (mm) up to 3000 3001 - 3900 3901 - 5100 5101 - 6500 6501 - 6800 up to 3000 3001 - 3900 3901 - 5100 5101 - 6000 up to 3000 3001 - 3900 3901 - 5100 5101 - 6500 6501 - 6800 width (mm) up to 7000 5405- 7000 up to 4200 up to 6000 up to 5700 up to 6000 up to 7000 5405- 7000 dimension panel A BC A1* A2 390 440 200 150 150 460 476 492 696 200 N/A 100 710 754 790 696 710 250 N/A 100 760 790 830 D E* F 100 700 700 100 700 700 200 1000 600 G 590 640 660 675 692 1040 744 765 831 885 915 *A1 recommended sideroom based on the opener being installed. A2 recommended sideroom without opener. *E recommended sideroom length based on the opener being installed Doc: 165026_00 Released: 02/03/2023 All references are taken from inside looking out. Roll-A-Shutter Structural fixing detail for shutter openings 2 Please follow diagram for correct installation of shutters up to: 10000mm high x 12000mm wide A1/A2 G B CEILING E · Fixing (shown shaded) steel. · Material for wind rated doors MUST comply with the DTC drawings, which can be found on the B&D website. · Depending on door size and weight, steel will be required. All masonry must be solid bricks or core filled. Steel must be of a suitable thickness. If unsure consult with your engineer or B&D representative. · If floor rebate is required it must extend at least 100mm more than the opening on each side and back from the fixing face at least 100mm. OPENING HEIGHT C B A1/A2 OPENING D F FLOOR REBATE SOLID RETURN installation Spring Balanced Springless Direct Drive Springless Direct Lift Chain Drive height (mm) up to 2400 2401 - 3000 3001 - 3900 3901 - 5100 5101 - 6500 up to 3000 3001 - 3900 3901 - 5100 5101 - 6500 6501 - 6800 up to 3000 3001 - 4200 4201 - 5400 5401 - 6500 6501 - 7500 7501 - 9000 9501 - 10000 width (mm) 7000 - 10000 7000 - 9000 7000 - 8500 7000 - 8000 7000 - 7500 7000 - 9000 7000 - 8500 7000 - 8500 7000 - 7500 7000 7000 - 12000 dimension panel A A1* A2 B C 390 440 200 150 150 460 476 492 700 768 200 N/A 100 820 850 860 720 768 820 250 N/A 100 850 860 890 910 D E* F 100 700 700 100 700 700 200 1000 600 G 590 640 660 676 692 1040 780 852 930 975 990 1010 1040 *A1 recommended sideroom based on the opener being installed. A2 recommended sideroom without opener. *E recommended sideroom length based on the opener being installedAdobe PDF Library 17.0 Adobe InDesign 18.2 (Windows)