Milesight | 5G, AI, IoT and LoRaWAN®
User Guide for Milesight models including: EM500-CO2, EM500-LGT, EM500-PP, EM500-PT100, EM500-SMT, EM500-SMTC, EM500-SWL, EM500-UDL, EM500 Series LoRaWAN Light Sensor, EM500 Series, EM500 Series Light Sensor, LoRaWAN Light Sensor, Light Sensor, LoRaWAN Sensor, Sensor
MileSight EM500-LGT- LoRaWAN Light Sensor | ETM Pacific
File Info : application/pdf, 21 Pages, 866.79KB
DocumentDocumentEM500 Series User Guide Xiamen Milesight IoT Co., Ltd. EM500 Series User Guide Applicability This guide is applicable to EM500 series sensors shown as follows, except where otherwise indicated. Model Description EM500-CO2 Carbon Dioxide Sensor EM500-LGT Light Sensor EM500-PP Pipe Pressure Sensor EM500-PT100 PT100 Temperature Sensor EM500-SMT Soil Moisture Sensor EM500-SMTC Soil Moisture Moisture, Temperature and Conductivity Sensor EM500-SWL Submersible Level Sensor EM500-UDL Ultrasonic Distance/Level Sensor Safety Precautions Milesight will not shoulder responsibility for any loss or damage resulting from not following the instructions of this operating guide. The device must not be remodeled in any way. The device is not intended to be used as a reference sensor, and Milesight will not should responsibility for any damage which may result from inaccurate readings. Do not place the device close to objects with naked flames. Do not place the device where the temperature is below/above the operating range. Make sure electronic components do not drop out of the enclosure while opening. When installing the battery, please install it accurately, and do not install the reverse or wrong model. The device must never be subjected to shocks or impacts. Declaration of Conformity EM500 series is in conformity with the essential requirements and other relevant provisions of the CE, FCC, and RoHS. © 2011-2021 Xiamen Milesight IoT Co., Ltd. All rights reserved. www.milesight-iot.com 2 EM500 Series User Guide All information in this guide is protected by copyright law. Whereby, no organization or individual shall copy or reproduce the whole or part of this user guide by any means without written authorization from Xiamen Milesight IoT Co., Ltd. For assistance, please contact Milesight technical support: Email: iot.support@milesight.com Tel: 86-592-5085280 Fax: 86-592-5023065 Revision History Date Nov. 23, 2020 Doc Version Description V 1.0 Initial version www.milesight-iot.com 3 Contents EM500 Series User Guide 1. Product Introduction................................................................................................................................. 5 1.1 Overview........................................................................................................................................... 5 1.2 Features............................................................................................................................................5 2. Hardware Introduction..............................................................................................................................5 2.1 Hardware Overview.........................................................................................................................5 2.2 Dimensions(mm)............................................................................................................................ 6 2.3 Power Button Descriptions............................................................................................................7 3. Basic Configuration...................................................................................................................................8 3.1 Configuration via Smartphone APP............................................................................................. 8 3.1.1 Read/Write Configuration via NFC....................................................................................8 3.1.2 Template Configuration......................................................................................................9 3.2 Configuration via PC.....................................................................................................................10 3.2.1 Log in the Toolbox.............................................................................................................10 3.2.2 Basic Configuration...........................................................................................................12 3.2.3 Template Settings............................................................................................................. 13 3.2.4 Upgrade............................................................................................................................... 13 4. Advanced Feature Description..............................................................................................................14 4.1 LoRaWAN Settings....................................................................................................................... 14 4.2 Basic Settings................................................................................................................................15 4.3 Calibration...................................................................................................................................... 15 4.4 Threshold and Alarm.................................................................................................................... 15 5. Milesight IoT Cloud Management........................................................................................................ 16 5.1 Add a Milesight Gateway............................................................................................................. 16 5.2 Add EM500 to Milesight IoT Cloud............................................................................................ 17 6. Sensor Payload........................................................................................................................................18 6.1 Basic Information..........................................................................................................................18 6.2 Sensor Data....................................................................................................................................18 6.3 Downlink Commands................................................................................................................... 20 Appendix....................................................................................................................................................... 20 Default LoRaWAN Parameters.......................................................................................................... 20 Default Uplink Channels..................................................................................................................... 21 www.milesight-iot.com 4 EM500 Series User Guide 1. Product Introduction 1.1 Overview EM500 series is a sensor mainly used for outdoor environment through wireless LoRa network. EM500 device is battery powered and designed for multiple mounting ways. It is equipped with NFC (Near Field Communication) and can easily be configured by a smartphone or a PC software. Sensor data are transmitted in real-time using standard LoRaWAN® protocol. LoRaWAN® enables encrypted radio transmissions over long distance while consuming very little power. The user can obtain sensor data and view the trend of data change through Milesight IoT Cloud or through the user's own Network Server. 1.2 Features Up to 11km communication range Easy configuration via NFC Standard LoRaWAN® support Milesight IoT Cloud compliant Low power consumption with 19000mAh replaceable battery 2. Hardware Introduction EM500 series sensors is made up of a LoRa transceiver and a sensor. Among them, ultrasonic sensors and gas sensors are combined with LoRa transceiver. 2.1 Hardware Overview Front View of EM500: LoRa Antenna (Internal) NFC Area Water-proof Connector www.milesight-iot.com 5 Front View of EM500-CO2: LoRa Antenna (Internal) NFC Area Vent Tube EM500 Series User Guide Front View of EM500-UDL: LoRa Antenna (Internal) NFC Area Ultrasonic Horn Back View: Battery (Internal) Wall Mounting Holes Pole Mounting Holes 2.2 Dimensions(mm) EM500 www.milesight-iot.com 6 EM500-CO2 EM500-UDL EM500 Series User Guide 2.3 Power Button Descriptions Note: EM500 can also be turned on/off and reset via Mobile APP or Toolbox. Function Action LED Indication Turn On Press and hold the button for more than 3s. Off Static Green Turn Off Press and hold the button for more than 3s. Static Green -> Off Press and hold the button for more than 10s. Reset Note: EM500 will automatically power on after Blink 3 times. reset. Check Quickly press the power button. On/Off Status Light On: Device is on. Light Off: Device is off. www.milesight-iot.com 7 EM500 Series User Guide 3. Basic Configuration EM500 sensor can be monitored and configured via one of the following methods: Mobile APP (NFC); Windows software (NFC or Type-C port). In order to protect the security of sensor, password validation is required when configuring via unused phone . Default password is 123456. 3.1 Configuration via Smartphone APP Preparation: Smartphone (NFC supported) Toolbox APP: download and install from Google Play or Apple Store. 3.1.1 Read/Write Configuration via NFC 1. Enable NFC on the smartphone and open"Toolbox"APP. 2. Attach the smartphone with NFC area to the device to read basic information. Note: Ensure the location of smartphone NFC area and it is recommended to take off phone case before using NFC. 3. Change the on/off status or parameters, then attach the smartphone with NFC area to the device until the APP shows a successful prompt. www.milesight-iot.com 8 EM500 Series User Guide 4. Go to"Device > Status" to tap"Read"and attach the smartphone with NFC area to the device to read real-time data of sensor. 3.1.2 Template Configuration Template settings only work for easy and quick device configuration in bulk. Note: Template function is allowed only for sensors with the same model and LoRa frequency band. 1. Go to "Template" page on the APP and save current settings as a template. 2. Attach the smartphone with NFC area to another device. www.milesight-iot.com 9 EM500 Series User Guide 3. Select the template file from Toolbox APP and tap "Write",keep the two devices close until the APP shows a successful prompt. 4. Slide the template item to the left to edit or delete the template. 3.2 Configuration via PC Preparation: Dedicated NFC Reader or Type-C USB cable PC (Windows 10 is recommended) Toolbox: https://www.milesight-iot.com/software-download/ 3.2.1 Log in the Toolbox Make sure "Toolbox" is downloaded on your computer. Select one of the following methods to log in Toolbox. Type-C Connection 1. Open the case of EM500 and connect the EM500 to computer via type-C port. www.milesight-iot.com 10 EM500 Series User Guide 2. Select type as "General" and click password to log in Toolbox. (Default password: 123456) NFC Connection 1. Connect the NFC reader to computer, then attach the EM500 to NFC area of the reader. 2. Select type as "NFC" and serial port as NFC reader port on Toolbox. www.milesight-iot.com 11 3.2.2 Basic Configuration 1. Click "Read" to read current data of the sensor. EM500 Series User Guide 2. When you perform one of the following operations, enter the password and wait a few seconds until toolbox shows a successful prompt. (Password is not need if you connect it via type-C port) Turn on/off the sensor Reset the sensor Click"Write"to change settings Upgrade www.milesight-iot.com 12 EM500 Series User Guide 3.2.3 Template Settings Note: Template function is allowed only for sensors with the same model and LoRa frequency band. 1. Go to "Maintenance -> Template and Reset" page in Toolbox. 2. Click "Export" to save the current settings as a template. 3. Click "Browse" to select the correct template from computer. 4. Click "Import" to import the template to the device. 3.2.4 Upgrade 1. Download firmware on your computer. 2. Go to "Maintenance -> Upgrade"page in Toolbox. 3. Click"Browse"and select the firmware from computer. 4. Click"Upgrade"to upgrade the device. Note: If NFC connection is selected, please keep the two devices close and don't move them in order to get the best connectivity as possible when upgrading. www.milesight-iot.com 13 EM500 Series User Guide 4. Advanced Feature Description 4.1 LoRaWAN Settings Parameters Description Default Device EUI Unique ID of the sensor. It can be found on the On the label label. App EUI App EUI of the sensor. 24E124C0002A0001 The port used for sending or receiving data. Application Port 85 Default: OTAA or ABP mode. Join Type Note: If you use Milesight IoT cloud to manage OTAA sensors, please select OTAA mode. Application Key Appkey of the sensor. 5572404C696E6B4C 6F52613230313823 Network ID NetID of the sensor used for identifying 0x010203 LoRaWAN networks. Device Address DevAddr of the sensor. The 5th to 12th digits of SN. Network Session Key Nwkskey of the sensor. 5572404C696E6B4C 6F52613230313823 Application Session Key Appskey of the sensor. 5572404C696E6B4C 6F52613230313823 Spread Factor Select spread factor from SF7 to SF12. SF10-DR2 Confirmed Mode If the sensor does not receive ACK package from network server, it will resend data 3 times Disabled most. Sensor will send specific mounts of LoRaMAC Rejoin Mode packages to check connection status regularly. Enabled, 8 packages If no reply after specific packages, the sensor will re-join. ADR Mode Allow network server to adjust datarate of the Enabled sensor. Support Frequency LoRaWAN region. EU868 AU915 www.milesight-iot.com 14 Channel EM500 Series User Guide Enable or disable LoRa channels. If frequency is one of CN470/AU915/US915, you can enter the index of the channel that you want to enable in the input box, making them separated by commas. Examples: 1, 40: Enabling Channel 1 and Channel 40 1-40: Enabling Channel 1 to Channel 40 1-40, 60: Enabling Channel 1 to Channel 40 and Channel 60 All: Enabling all channels Null: Indicates that all channels are disabled Appendix 4.2 Basic Settings Parameters Description Reporting Interval Interval of sending sensor data. Default: 10min. Change the password of logging Toolbox (Windows) and parameter Change Password modify(mobile APP). 4.3 Calibration Parameters Description After saving the calibration value, the sensor will add the calibration value to raw value and send the final value. If current value exceeds the outlier range/values, the sensor will re-collect the value. Note: This item is only for EM500-UDL. 4.4 Threshold and Alarm Parameters Over/Below Data Collecting Interval Description Maximum/minimum data to trigger the alarm. After triggered, sensor will send current data ignoring report interval. The sensor will detect and check whether the value is triggered again after data collecting interval. www.milesight-iot.com 15 EM500 Series User Guide 5. Milesight IoT Cloud Management EM500 sensors can be managed by Milesight IoT Cloud platform. Milesight IoT cloud is a comprehensive platform that provides multiple services including device remote management and data visualization with the easiest operation procedures. Please register a Milesight IoT Cloud account before operating following steps. 5.1 Add a Milesight Gateway 1. Enable "Milesight" type network server and "Milesight IoT Cloud" mode in gateway web GUI. Note: Ensure gateway has accessed the Internet. 2. Go to "My Devices" page and click "+New Devices" to add gateway to Milesight IoT Cloud via SN. Gateway will be added under "Gateways" menu. www.milesight-iot.com 16 EM500 Series User Guide 3.Check if gateway is online in Milesight IoT Cloud. 5.2 Add EM500 to Milesight IoT Cloud 1. Go to "My Devices" page and click "+New Devices". Fill in the SN of EM500 and select associated gateway. 2. After EM500 is connected to Milesight IoT Cloud, you could check the device information and data and create dashboard for it. www.milesight-iot.com 17 EM500 Series User Guide 6. Sensor Payload All data are based on following format(HEX): Channel1 Type1 Data1 Channel2 Type2 Data2 Channel 3 ... 1 Byte 1 Byte N Bytes 1 Byte 1 Byte M Bytes 1 Byte ... 6.1 Basic Information EM500 sensors report basic information of sensor everytime joining the network. Channel Type 01(Milesight Protocol Version) Data Example 01 09 (Hardware Version) ff 0a(Software Version) 0f(Device Type) 01 40 01 14 00 16Device SN 64 10 90 82 43 75 00 01 Description V1 V1.4 V1.14 Class A Device SN is 6410908243750001 6.2 Sensor Data EM500 sensors report sensor data according to reporting interval (10min by default). Battery level is reported every 24 hours. EM500-CO2 Channel Type Data Example 01 75(Battery Level) 64 Description 64=>100 Battery level =100% www.milesight-iot.com 18 03 67 (Temperature) 04 68(Humidity) 05 7dCO2 73Barometric 06 Pressure 10 01 71 67 04 68 27 EM500 Series User Guide 10 01 => 01 10 = 272 Temp=272*0.1=27.2°C 71=>113 Hum=113*0.5=56.5% 67 04 => 04 67 =1127 ppm 68 27=>27 68=10088 Pressure=10088*0.1=1008.8hPa EM500-LGT Channel 01 03 Type 75(Battery Level) 94 (Light) Data Example 64 50 00 00 00 Description 64=>100 Battery level =100% 50 00 00 00=>00 00 00 50=80 lux EM500-PP Channel Type Data Example 01 75(Battery Level) 64 03 7b (Pressure) 0a 00 Description 64=>100 Battery level =100% 0a 00=>00 0a=10kPa EM500-PT100 Channel Type Data Example 01 75(Battery Level) 64 03 67 (Temperature) 10 01 Description 64=>100 Battery level =100% 10 01 => 01 10 = 272 Temp=272*0.1=27.2°C EM500-SMT/SMTC Channel Type Data Example 01 75(Battery Level) 64 Description 64=>100 Battery level =100% www.milesight-iot.com 19 03 67 (Temperature) 10 01 04 68(Moisture) 05 7dConductivity 71 f0 00 EM500 Series User Guide 10 01 => 01 10 = 272 Temp=272*0.1=27.2°C 71=>113 Hum=113*0.5=56.5% f0 00 => 00 f0 =240 µs/cm EM500-SWL Channel Type Data Example 01 75(Battery Level) 64 03 77 (Water Level) 02 00 EM500-UDL Channel Type Data Example 01 75(Battery Level) 64 03 82 (Distance) 1e 00 Description 64=>100 Battery level =100% 02 00=>00 02=2cm Description 64=>100 Battery level =100% 1e 00=>00 1e=30mm 6.3 Downlink Commands EM500 sensors support downlink commands to configure the device. Application port is 85 by default. Channel Type ff 03(Set Reporting Interval) Data Example b0 04 Description b0 04 => 04 b0 = 1200s Appendix Default LoRaWAN Parameters 24E124 + 2nd to 11th digits of SN DevEUI e.g. SN = 61 26 A1 01 84 96 00 41 Then Device EUI = 24E124126A101849 AppEUI 24E124C0002A0001 www.milesight-iot.com 20 EM500 Series User Guide Appport NetID DevAddr AppKey NwkSKey AppSKey 0x55 0x010203 The 5th to 12th digits of SN e.g. SN = 61 26 A1 01 84 96 00 41 Then DevAddr = A1018496 5572404C696E6B4C6F52613230313823 5572404C696E6B4C6F52613230313823 5572404C696E6B4C6F52613230313823 Default Uplink Channels Model EM500-470M EM500-868M EM500-915M Channel Plan CN470 EU868 RU864 IN865 AU915 US915 KR920 AS923 Channel Settings/MHz 470.3~489.3(All 95 channels) 868.1, 868.3, 868.5 868.9, 869.1 865.0625, 865.4025, 865.6025 915.2~927.1 (All 72 channels) 902.3~914.2 (All 72 channels) 922.1, 922.3, 922.5 923.2, 923.4 -END- www.milesight-iot.com 21