Installation Guide for MAGUS models including: HT-X33050 Hitch Class 3 Acura Honda, HT-X33050, Hitch Class 3 Acura Honda, Class 3 Acura Honda, Acura Honda
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
Hitch Installation Instruction REV.20240701 Part# HT-X33050 Application For 2007-2014 Ford Edge\2007-2015 Lincoln MKX Hardware List Hitch Parts HW B (For Hitch Installation) Item Part Name A Hitch Body 1# Carriage Bolts 2# Carriage Bolts 3# Hex Flange Nuts QTY Description Item Part Name QTY Description 1 B/C Mounting Brackets 2 B-Driver Side C-Passenger Side 2 M12X1.75-45 4# Spacers 6 With SQ hole 4 M12X1.75-40 5# Fishwire 4 6 M12X1.75 HW A (For Hitch Assembly) 6# Hex Bolts 7# Flat Washers 6 M12X1.75-35 8# Lock Washers 10 M12 9# Hex Flange Nuts 6 M12 4 M12 Gross Load Capacity When Used As A Weight Carrying Hitch:4000 LBS. Trailer Weight & 400 LBS. Tongue Weight. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY. *** Drilling Required Trimming Required REAR The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. Thank you for choosing our product! Page 1 of 3 Hitch Installation Instruction REV.20240701 Part# HT-X33050 Application For 2007-2014 Ford Edge\2007-2015 Lincoln MKX Step Description 1 Assemble Hitch Body (A) and Mounting Brackets (B, C) with (6) M12X1.75-35mm Hex Bolts, (10) M12 Flat Washers, (6) M12 Lock Washers, (4) M12 Hex Flange Nuts.(Hardware in "HW A"). Lower exhaust by removing the rear (3) exhaust hangers. It may be required to use some wire to hold the exhaust up high enough to prevent damage to the exhaust. (See RUBBER ISOLATOR REMOVAL DIAGRAM) 2 Remove heat shield from both sides of vehicle by removing the (3) 6mm bolts and (1) black plastic plug. The driver side heat shield will also be connected to the rear wiring harness by a plastic plug. Once heat shield is removed trim off tab. (See HEAT SHIELD TAB REMOVAL diagram) Reattach heat shield without the screws in the frame rails. Heat shield will then be sandwiched between vehicle frame rails and hitch. 3 Fishwire carriage bolts with spacers through rear of bumper mounts to holes in frame rails, as shown. (See FISHWIRE TECHNIQUE DIAGRAM) 4 Raise hitch into postion and secure with flange nuts. (Note: Bumper facia trimming is required on Edge Sport. See Trim Diagram.) 5 The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. Thank you for choosing our product! Page 2 of 3 Hitch Installation Instruction REV.20240701 Part# HT-X33050 Application For 2007-2014 Ford Edge\2007-2015 Lincoln MKX 6 Using the hitch as a template, drill rear holes of hitch, both sides, using a 17/32" drill bit. 7 Fishwire carriage bolt and spacer through back of bumper mounts and attach with flange nuts. 8 Torque M12 hardware to 58 lb-ft. 9 Reinstall exhaust removed in Step 1. ***Periodically Check The Receiver Hitch To Ensure That All Fasteners *** Are Tight & All Structural Components Are Sound. The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. Thank you for choosing our product! Page 3 of 3WPS 文字