MikroTik ATL LTE18 kit

Safety Warnings

Before working on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Ultimate disposal of this product should be handled according to all national laws and regulations. All installation methods for mounting an access point on any wall surface are subject to the acceptance of local jurisdiction. The installation of the equipment must comply with local and national electrical codes. This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system. Use only the power supply and accessories approved by the manufacturer, which can be found in the original packaging of this product. Read the installation instructions before connecting the system to the power source. MikroTik cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your own risk! In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet. It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All MikroTik radio devices must be professionally installed. This is a Class A device. In a domestic environment, this product might cause radio interference, in which case the user might be required to take adequate measures.

Exposure to Radio Frequency Radiation: This MikroTik equipment complies with the European Union radiation exposure limits set forth for an uncontrolled environment. This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the general public.

Quickstart

1. Open the Ethernet port door.
2. Insert the SIM card into the slot, with the chip facing UP.
3. Connect the device to the included PoE injector with an Ethernet cable to the data+power end.
4. Connect the data end of the PoE injector to the computer.
5. Connect the power adapter to the PoE injector.
6. Open https://192.168.188.1 in your web browser.
7. User name: admin, and there is no password (or, for some models, check user and wireless passwords on the sticker).
8. Enter the PIN code, if required by your mobile network operator.
9. Use the check for update option to upgrade the device to the latest version. You must have an active SIM card with available data.
10. The device will reboot.
11. Connect again and in the QuickSet menu set a strong password.

Diagram Description: A diagram illustrates the connection process: the MikroTik device connects via an Ethernet cable to a PoE injector, which is then connected to a power adapter and a computer.

Powering

• Number of DC inputs: 1
• DC input type: PoE-in (12-57V)
• Power adapter nominal voltage: 24V
• Power adapter nominal current: 0.8A
• Max power consumption without attachments: 8W
• Max power consumption: 8W

Mounting

1. Slide the included metallic mounting rings into the two slots on the back of the antenna dish.
2. Attach the unit to a pole, with the Ethernet port pointing downward.
3. Use a PH2 screwdriver to tighten the rings.
4. Fix the Ethernet cable to the pole using zip ties, less than one meter from the unit, to avoid the cable being pulled out of the port.
5. Check mounting angle and positioning.

When mounting outdoors, please ensure that any cable openings are directed downwards. Use a POE injector and proper grounding; this device has a specially-designed grounding connector under the port cover. Recommended using shielded Cat5/6 cable. The IP rating scale for this device is IP54.

Configuration

Once logged in, it is recommended to click the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to conform to local regulations.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to the possibilities: https://mt.lv/help. In case an IP connection is not available, the Winbox tool (https://mt.lv/winbox) can be used to connect to the MAC address of the device from the LAN side (all access is blocked from the Internet port by default). For recovery purposes, it is possible to boot the device for reinstallation; see the section Reset button.

Accessories

The package includes the following accessories that come with the device:

• 24V 0.8A power adapter
• Gigabit PoE injector
• Hose clamp

Expansion slots and ports

• Product code: ATLGM&EG18-EA
• CPU: Dual-core 88F3720 1.2 GHz
• CPU architecture: ARM 64bit
• Size of RAM: 256 MB
• RAM type: DDR3L
• Storage: 16 MB, Flash
• Number of 1G Ethernet ports: 1
• LTE modem: R11mL-EG18-EA
• TAC: 86981604
• LTE Category 18 (1.2Gbps Downlink, 150Mbps Uplink)
• LTE bands: 1 (2100MHz) / 3 (1800MHz) / 5 (850MHz) / 7 (2600MHz) / 8 (900 MHz) / 20 (800MHz) / 28 (700MHz) / 38 (2600MHz) / 40 (2300MHz) / 41 (2500MHz)
• 3G Category R8 (42.2Mbps Downlink, 11.2Mbps Uplink)
• 3G Bands: 1 (2100MHz) / 3 (1800MHz) / 5 (850MHz) / 8 (900MHz)
• Dimensions: 315 mm diameter x 170 mm depth
• Operating system: RouterOS, License level 3
• Operating temperature: -40°C to +70°C

Reset button

The reset button has three functions:

• Hold this button during boot time until the LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).
• Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total of 10 seconds).
• Or, keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total of 15 seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. This is useful for RouterBOOT debugging and recovery.

Operating system support

The device supports RouterOS software version 7.5. The specific factory-installed version number is indicated in the RouterOS menu /system resource. Other operating systems have not been tested.

To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as at designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated disposal sites in your area.

CE Declaration of Conformity

Hereby, MikroTik SIA declares that the radio equipment type ATLGM&EG18-EA is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.com/products

WLAN/LTE Technical Specifications

This MikroTik device meets Maximum TX power limits per ETSI regulations. For more detailed information see Declaration of Conformity above.

Technical Specifications (Multilingual Summary)

The device specifications are provided in multiple languages, including technical details on product power input options, DC adapter output specifications, IP class of the enclosure, and operating temperature.

Example:

• (EN) Product Power Input Options
• (DE) Produkt Stromquellen Optionen
• (FR) Options d'entrée d'alimentation du produit
• (IT) Opzioni di ingresso alimentazione del prodotto
• (ES) Opciones de entrada de energía del producto
• (RU) Варианты входной мощности

Similar multilingual specifications are available for DC Adapter Output, IP Class, and Operating Temperature.