Installation Guide for tp-link models including: TL-PD30G-M2, TL-PD30G-M2 2.5G Desktop Switch PoE Plus Splitter, 2.5G Desktop Switch PoE Plus Splitter, Desktop Switch PoE Plus Splitter, Switch PoE Plus Splitter, PoE Plus Splitter, Splitter
TP-Link TL-PD30G-M2
Download for TL-PD30G-M2 | TP-Link Australia
Download für TL-PD30G-M2 | TP-Link Deutschland
File Info : application/pdf, 2 Pages, 2.20MB
DocumentDocumentInstallation Guide
2.5G PoE+ Splitter
© 2024 TP-Link 7106511510 REV1.0.0
Some products demonstrated in this guide may be unavailable in your country or region. For local sales information, visit https://www.tp-link.com.
PoE Splitter Only The PoE Splitter can be used with a PoE/PoE+ switch to deliver direct current (DC) power and data to a Non-PoE device.
PoE/PoE+ Switch
PoE Splitter
LAN OUT
PWR DC OUT
12V 9V 5V
Note: Set the required voltage of the non-PoE device before cable connection.
Non-PoE Device (suggested power: <24 W)
PoE Injector & Splitter The PoE injector and PoE splitter can be used as a kit to supply power and transmit data to a Non-PoE device.
Note: Set the required voltage of the non-PoE device before cable connection.
12V 9V 5V
PoE Splitter
Non-PoE Device (suggested power: <24 W)
LAN OUT
PWR DC OUT
Power Cord
PWR
PWR+DATA OUT DATA IN
PoE+ Injector
Ethernet Device (switch, router, etc.)
Power LED Explanation
LAN OUT
PWR DC OUT
On: Connected to PSE correctly Off: No PSE is connected
FAQ
Q1. Can the PoE splitter negotiate to 10/100/1000Mbps?
A: Yes. All RJ45 ports of the PoE splitter support 10M/100M/1000M/2.5Gbps auto-negotiation.
Q2. What can I do if my PoE splitter doesn't supply power to the powered device or the supplied power is unstable?
A1: Ensure the Switch or Injector is PoE-compliant and its connecting port supports the PoE function.
A2: Ensure the power consumption of the PD doesn't exceed 24W, otherwise the overload protection of the PoE injector will be activated. The quality and length of the Ethernet cable may influence the reception of the power supply.
Q3. Must I use the PoE injector together with the PoE splitter?
A: No. The PoE splitter is used with a PoE switch or the PoE injector to supply power to a non-PoE device. The PoE injector can supply power to all PDs supporting PoE function.
Q4. The Power LED of PoE splitter is not lit.
A1: Ensure the power cord is connected the PoE switch or injector with power source properly.
A2: Ensure the power consumption of the PD doesn't exceed 24W, otherwise the PoE switch or injector will activate the overload protection and the power will be cut off.
Safety Information
Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Do not use any other chargers than those recommended. Do not use damaged charger or USB cable to charge the device. Adapter shall be installed near the equipment and shall be easily accessible. This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.
Specifications
General Specifications
Standards LED Cable Type
IEEE 802.3i, IEEE802.3u, IEEE 802.3ab, IEEE 802.3bz, IEEE 802.3af, IEEE 802.3at
PWR
UTP/STP of Cat. 5 or above (based on the standards that the connected devices comply with)
Ports
10M/100M/1000M/2.5Gbps Auto-Negotiation RJ45 POWER+DATA IN Port 10M/100M/1000M/2.5Gbps Auto-Negotiation RJ45 LAN OUT Port 12V / 9V / 5V DC OUT Power Output Port
Environmental and Physical Specifications
Operating Temperature Storage Temperature Operating Humidity
-5°C to 45°C (23°F to 113°F) -40°C to 70°C (-40°F to 158°F) 10% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com/business to join TP-Link Community. For technical support and other information, please visit https://www.tp-link.com/support/?type=smb, or simply scan the QR code.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca
FCC compliance information statement
Product Name: 2.5G PoE+ Splitter Model Number: TL-PD30G-M2
Component Name
Model
I.T.E. POWER SUPPLY
T480038-2B1
Product Name: 2.5G PoE+ Splitter
Model Number: TL-PD30G-M2 Responsible party:
TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2024.09.25
FCC compliance information statement
Product Name: I.T.E. POWER SUPPLY Model Number: T480038-2B1 Responsible party: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2024.09.25
, .
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
FR Cet appareil et ses accessoires se recyclent
À DÉPOSER À DÉPOSER EN MAGASIN EN DÉCHÈTERIE
OU
BSMI Notice (For TL-PD30G-M2)
Points de collecte sur www.quefairedemesdechets.fr Privilégiez la réparaon ou le don de votre appareil !
Pb
Cd
Hg
Cr+6
PCB
-
-
1"" 2" - "
PBB
PBDE
Explanaon of the symbols on the product label
Symbols may vary from productsThe label is at the bottom of the product.
Symbol
Explanation
Cl a ss II equipment
Cl a ss II equipment with functional earthing Alternating current Direct current Pol a rity of d.c. power connector
For indoor use only
Dangerous voltage
Ca uti on, risk of electric shock Energy efficiency Ma rking Protecti ve earth Ea rth Fra me or chassis Functional earthing Ca uti on, hot surface Ca uti on Opera tor's manual Stand-by "ON"/"OFF" (push-push)
Fuse
Fuse is used in neutral N
RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Ca uti on, avoid listening a t high vol ume l evels for l ong periods
Di s connection, a ll power plugs
m
Switch of mini-gap construction
Switch of micro- gap construction (for US version)
µ
Switch of micro-gap /micro-disconnection construction
(for other versions except US)
Switch without contact gap (Semiconductor switching device)
Link: The wallet designed for the internet
quefairedemesdechets.fr
Business Community
TP-Link: Your Smart Home, Simplified