Installation Guide for Heights Telecom models including: 2BCFY-ERO1ETPRO, 2BCFYERO1ETPRO, ero1etpro, HT-880BE Mesh Extender, HT-880BE, Mesh Extender, Extender
Heights Telecom T LTD ERO1ETPRO 2BCFY-ERO1ETPRO 2BCFYERO1ETPRO ero1etpro
ERO1eT PRO Mesh Extender High-quality WiFi 6E mesh extender, designed to elevate your surfing experience to the highest level. This powerful extender seamlessly expands your network coverage, ensuring fast and reliable connectivity throughout your home. With easy setup and robust performance, it guarantees a smooth and interruption-free online experience, whether you're streaming, gaming, or working from home. Say goodbye to dead zones and buffering, and embrace the future of top-tier WiFi with our exceptional WiFi 6E mesh extender. 2.5G LAN/WAN Port 1G LAN Ports Package Contents: MU-MIMO Easy & Quick Installation 6E WiFi 6E AX Whole-Home Mesh Wi-Fi ERO1eT PRO Quick Installation Guide Extender ERO1eT PRO LED Indicators: Power Adapter LAN Cable Quick Installation Guide Stable - Booting up/gateway without internet Blinking - connection problem to gateway Stable - Ready for Adoption Blinking - Adoption in Progress Stable - Connected to internet Blinking - Weak WiFi signal, Improve location Connect the Hardware Follow these steps only after you have placed your home gateway and adapted it in the HomePass® by Plume app. 1 Connect the supplied power adapter to the ERO1eT PRO and a power outlet. 2 Turn on the router by pressing the power button. 3 On the HomePass® by Plume app in Home page, scroll down to the Adapt section. 4 Tap the to open the Options Menu. 5 Tap on Add a pod. 6 Tap on Other setup options... 7 You can choose to 'Scan a QR code' or 'Enter a serial number' to add the device. The QR code and serial number are located on the right side of the device. 8 Click 'Next,' and the device will be added. All WiFi configurations will adapt from your home router, creating one mesh Wireless Network (SSID). 4 5 6 Back Panel FCC Regulations: Reset Button Power Button 2 Power Jack 1 2.5 Gigabit LAN/WAN Ports (2-3) Gigabit LAN Ports (2-3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Note: Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment. 1. FCC regulat ions rest rict t he operat ion of t his device t o indoor use only. 2. The operat ion of t hisdevice is prohibit ed on oil plat forms, cars, t rains, boat s, and aircraft , except t hat operat ion of t his device is permit t ed in large aircraft w hile flying above 10,000feet . 3. Operat ion of t ransmit t ers in t he 5,925-7,125 GHz band is prohibit ed for cont rol of or communicat ions w it h unmanned aircraft syst ems. RF Exposure Information This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm during normal operation. , 1.Dimension after folding()150*150mm 2.Print colour()4Colour printing (). 3.Material()128g copperplate paper(128g ). 4.Coating()Matte lamination) 5.Binding process()Paper folding()---- 6.Output lpi()200 lpi. 7.Tolerance()L()*W():±1mm. 8.Raw materials and the corresponding post processing should meet requirements defined in the T&W Environmental Protection Technical Standards. (). Heights QUICK INSTALLATION GUIDE HT-880BE V01 N/A 1/1 610000013160 20230810 N/AAdobe PDF library 17.00 Adobe Illustrator(R) 24.0