Digital Night Vision | SIONYXSubmit a ticket : SIONYXRegister Your Camera | SIONYX Night Vision Solutions
User Guide for SIONYX models including: C012800, Nightwave Ultra Low-Light Marine Camera, Low-Light Marine Camera, Marine Camera, C012800, Camera
Nightwave Quickstart Guide : SIONYX
SIONYX Nightwave™ Ultra Low-Light Marine Camera SIONYXC012800
SIONYX NIGHTWAVE⢠ULTRA LOW-LIGHT MARINE CAMERA
File Info : application/pdf, 2 Pages, 2.29MB
DocumentDocument1 2 3 4 FRONT BASE PLATE D B B A A B B C FRONT OF UNIT INCLUDED NIGHTWAVE CAMERA POWER + ANALOG VIDEO CABLE 5M SMA TO BNC ADAPTER BNC TO RCA ADAPTER POWER FUSE + FUSE HOLDER DIGITAL USB VIDEO CABLE 2M BASE GASKET MOUNTING HARDWARE KIT INSTALL TEMPLATE 5 6 7 8 9 BACK PARTS LEGEND 1 PIVOTING HEAD 2 CAMERA OPTIC 3 MAIN HOUSING 4 BASE PLATE 5 STATUS LED 6 TILT LOCK 7 CENTER MARK 8 LOCKING SCREW 9 UNLOCK MARK A M6 THREADED B TOP DOWN THROUGH HOLES C 1/4 20 TRIPOD MOUNT D CABLE HOLE LED STATUS ORANGE BLUE RED BOOTING RUNNING FAULT Prior to installing the camera, consider the following: · Select an installation location as high as practical with minimum obstructions. · Select an installation location that is greater than 1m from any magnetic compass. · Select an installation location that is greater than 1m from any source of EMI. · The mounting surface must be horizontal and level. · Ensure the camera installation hardware does not weaken the boat's structure. · Choose a drill size appropriate for the installation surface material and types of fasteners. · Ensure there are no hidden structures, wires or conduits beneath the install area that may be damaged by the installation hardware. · Ensure cable length and routing is adequate for installation location interference. (Radio, generators, motors, radar) T H I S I S S I O N Y X . We believe that human endeavor should not be limited by daylight. In the darkness of night, greatness is possible. Adventure enabled. And a full sense of all sight achievable, no matter the light. REGISTER YOUR DEVICE Register your device and stay up to date by visiting the URL or scanning the QR code below. NEED HELP? ONLINE CHAT SUBMIT A TICKET 24/7 SUPPORT www.sionyx.com www.sionyx.com/contact www.support.sionyx.com www.sionyx.com/register FOLLOW US Share your SIONYX content and be sure to tag us! R2 QUICK START GUIDE SIONYX.COM SEPARATE CAMERA FROM BASE PLATE 1 Loosen the LOCKING SCREW. FIG.1 2 Rotate MAIN HOUSING until UNLOCK MARK is aligned with the CENTER MARK. 3 Separate the base plate from the camera. FIG.1 CONNECT CABLES 1 Separate camera from base plate. 2 Remove cable retainer with the included Allen wrench. FIG.2 3 Remove rubber gasket from cable. FIG.2B 4 Remove connector protective cover. FIG.2C 5 Remove cable strain relief cover. FIG.2D 6 Separate connectors & remove cable from housing. 7 Feed new cable through housing FIG.2A & install rubber gasket around it. FIG.2B 8 Mate connectors, lay them in position and install the protective cover. 9 Pull extra cable slack through housing FIG.2A & re-install cable retainer. FIG.2 10 Re-connect the base plate to the camera. FIG.2 FIG.2B FIG.2C FIG.2A FIG.2D CONNECT TO POWER Follow marine electrical standards when wiring the camera. 1 Determine that proper voltage levels are available. (12V DC) 2 Finalize cable installation. 3 Install in-line fuse. VII 4 Connect power wires to corresponding positive and negative power terminals. II + III 5 If using USB-A connecter instead, see DIAGRAM 2 CONNECT TO VIDEO 1 Locate the video input on your display. 2 Install appropriate adapter if necessary. FIG.4 DIAGRAM 1 3 Connect Analog video output DIAGRAM 1 to Analog video input of your display. 4 If using USB-A connector instead, see DIAGRAM 2 ADJUST THE TILT FIG.5 1 Remove protective rubber cap and loosen the TILT LOCK SET SCREW. FIG.5 2 Set the angle by manually adjusting the pivoting head of the camera, forward and back. 3 Gently tighten the set screw and replace the rubber protective cap. DIAGRAM 1 II III I IV FIG.4 VII VI V DIAGRAM 2 VIII I WATERPROOF CONNECTOR ON CAMERA END II +12V TERMINAL III GROUND TERMINAL IV IN LINE FUSE HOLDER + FUSE V SMA VIDEO CONNECTION VI SMA TO BNC ADAPTER USE IF NECESSARY VII BNC TO RCA ADAPTER USE IF NECESSARY VIII USB POWER + VIDEO SEPARATE CABLE GET THE FULL USER MANUAL FOR INSTALL INSTRUCTIONS Aim your cellphone camera at the QR code to download the full NIGHTWAVE User Manual. EN Full Documentation FR Documentation Complète IT Documentazione Completa SP Documentación Completa DE Vollständige Dokumentation