Instruction Manual for BRANDMOTION models including: FVMR-1191 FullVUE Rear Camera Mirror, FVMR-1191, FullVUE Rear Camera Mirror, Rear Camera Mirror, Camera Mirror, Mirror
Brandmotion FVMR-1191 FullVUE™ replacement rear-view mirror/monitor with front- and rear-view cameras for select Chevy/GMC vehicles at Crutchfield
FullVUE® Rear Camera Mirror for Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) FVMR-1191 Recommended Tools Difficulty Level Wrench Wire Strippers Wire Cutters Electrical Tape Install Time Screw Driver Panel Removal Tool Zip Ties Socket Set 2hrs - 3hrs Questions? Call the Brandmotion technical support line at (734) 619-1250 or CLICK HERE AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 1/9 Kit Contents Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Components for installing the FVMR-1191 Kit Contents: FullVUE® Mirror & Harness 3rd Brake Light Bracket & Camera 9m Camera Harness AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 2/9 Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Installation of the FullVUE Mirror & Wire Connections Part 1 Attaching the FullVUE® Mirror to the windshield 1. Remove the old mirror from the mount on the windshield as per manufacturer's directions. Be sure to use the proper removal tool if required. 2. Install new mirror onto the D-tab and tighten with a Phillips screwdriver. Take care not to overtighten. Overtightening could result in damage to your windshield. Part 2 Powering the FullVUE® Mirror 1. Connect the power harness to the plug on the mirror. Route the harness across the top of the head liner, along the windshield, and down the A-pillar, and to the desired location in the kick panel. 2. Ensure that the harness will not be pinched when trim panels are replaced. AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 3/9 Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Installation of the FullVUE Mirror & Wire Connections Part 3 Wiring the FullVUE Mirror 1. Connect the RED wire from the mirror harness to 12-volt accessory power. 2. Connect the YELLOW wire from the mirror harness to 12-volt constant power. 3. Connect the BLACK wire to a solid ground. Chassis ground in the kick panel is recommended. Part 4 Function test of the FullVUE Mirror 1. Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 4/9 Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Disassembly Part 1 Lower the rear of the headliner 1. Remove the rear door seals off of the top of the pinch welds. 2. Use a trim removal tool to remove the cover from the coat hook. 3. Use an 8mm socket to remove the bolt from the coat hook. 4. Pull the coat hook to release the clip. 5. Use a trim removal tool to remove C-pillar plastic panels. 6. Use a 7mm socket to remove bungie from the plastic panel. 7. Slide your fingers on the inside of the back of the headliner by the rear window and feel for two plastic clips. 8. Once located gently pull from either side of the clip until it snaps out. Do this for both clips. 9. The headliner should now fall away from the rear half of the cab.( Be careful not to crease the headliner.) AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 5/9 Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Disassembly Part 2 Removing the spoiler from the rear of the cab 1. Reach a 10mm socket behind the headliner and remove the eight nuts and four bolts that hold the spoiler on. 2. Gently pull on the spoiler from the outside until it snaps free. 3. Release power connector to free the spoiler from the cab. Part 3 Mounting the Camera 1. On the backside of the spoiler, remove the four Phillips screws holding the brake light into the housing. 2. Push the two retaining tabs in to release the brake light. 3. The brake light should now come out. 4. Slot the Camera Bracket over the screw posts on the third brake light. 5. Snap the brake light back in place and screw in the four Phillips screws AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 6/9 Running Wires Part 1 Video Connector 1. Connect the 9m camera harness to the mirror harness at the connection by the mirror. 2. Run the 9m camera harness from the FullVUE Mirror through the headliner toward the brake light. 3. Pull the video connector of the 9m camera harness through the grommet to the outside of the cab. 4. Connect the 9m camera harness to the camera. Make sure to line up the arrows on the connectors Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 7/9 Assembly Part 1 Spoiler Reattachment 1. Reconnect the brake light plug. 2. Line up the spoiler with the holes in the cab and gently push it until it snaps in place. 3. Inside the cab, reinstall the four 10mm bolts and eight 10mm nuts. Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Part 2 Hanging the Headliner 1. Line up the two plastic headliner clips and snap them in place. 2. Reattach the bungie from the C-pillar panel with a 7mm socket. 3. Snap the C-pillar panel back in place. 4. Snap the coat hook back in place and screw in the 8mm bolt. 5. Snap the cover over the coat hook. 6. Put the door seals back over the pinch welds. AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 8/9 Vehicle Application: Chevrolet & GMC Trucks (2019-Current) & Heavy Duty (2020-Current) Part Number: FVMR-1191 Adjustment Part 1 Bezel Viewing Adjustment 1. If you need to change the camera's pitch, gently bend the bracket until it reaches the desired view angle. AR_1_10_2023 FullVUE® Rear Camera Mirror - FVMR-1191 Page 9/9GPL Ghostscript 9.55.0