Altronix Home
Installation Guide for Altronix models including: Pace1PRM, IP and PoE Receiver Over Extended Distance UTP or CAT5e, Extended Distance UTP or CAT5e, Extended Distance UTP, IP and PoE Receiver, Distance UTP
Altronix PACE1PRM | Long Range Ethernet Single Port Receiver
File Info : application/pdf, 4 Pages, 854.31KB
DocumentDocumentPace1PRM IP and PoE+ Receiver Over Extended Distance I.T.E. 43KC UTP or CAT5e Z1409 Installation Guide Overview: Pace1PRM is a long range Ethernet receiver which transmits data at 100Mbps full duplex and power via a single twisted pair (UTP) or CAT5e or higher cable in a PoE(+) compliant format. Pace1PRM receiver is powered via a PoE midspan, such as the Altronix Netway series, or by an endspan. The receiver passes the PoE(+) compliant power over the cable to the Pace1PTM or Pace1ST transceiver which, in turn, passes this power to an enabled IP camera/device. These plug and play units facilitate cost-effective solutions for IP devices that need to be installed at distances greater than 100m. They also provide a simple way to replace legacy analog products with new IP devices over single twisted pair (UTP) or structured cable. Features: Agency Listings: · UL/cUL Listed for Information Technology Equipment (UL 60950-1). · CE European Conformity. · C-Tick compliant. Input: · Powered by midspan or endspan. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W). Ethernet: · Connectivity: RJ45, auto-crossover. · Wire type: 4-pair CAT5 or 1 pair UTP structured cable. · Distance: up to 500m. · Speed: 10/100BaseT, half/full duplex, auto negotiation. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W) delivered to camera by Pace1PTM or Pace1ST. Power provided by Pace1PRM to Pace1PTM or Pace1ST by PoE protocol.* · Throughput is rated to pass 100Mbps of data at distances up to 500m. With proper headend equipment, this supports Megapixel, HD720, HD1080. CAT5e or Higher: · Distance: up to 500m @ 100Mbps (see Maximum Length of CAT5e Type or UTP vs. Camera Power/PoE Class, pg. 4). UTP (Single Pair): · Distance: up to 153m @ 100Mbps, up to 500m @ 10Mbps (see Maximum Length of CAT5e Type or UTP vs. Camera Power/PoE Class, pg. 4). LED Indicators: · Green - PoE ON (by respective RJ45 jack). · Yellow and Green LED IP Link status, 10/100Base-T/active. Environmental: · Operating Temperature: Pace1PRM: 20ºC to 49ºC ( 4ºF to 120.2ºF). Pace1PTM: For 15W: 40ºC to 75ºC ( 40ºF to 167ºF). For 25W: 40ºC to 70ºC ( 40ºF to 158ºF). For 30W: 40ºC to 60ºC ( 40ºF to 140ºF). Pace1ST: For 15W: 40ºC to 75ºC ( 40ºF to 167ºF). For 30W: 40ºC to 49ºC ( 40ºF to 120ºF). · Storage Temperature: 40ºC to 75ºC ( 40ºF to 167ºF). · Humidity: 20 to 85%, non-condensing. Functions: · Auto detection and protection of legacy non-PoE cameras/devices. Applications: · Extend Network link distance in an industrial environment over 700m. · Retrofit digital IP cameras in an analog CCTV CAT5e wired installations. · Works with Megapixel, HD720, HD1080, and VGA (SD) cameras. Mechanical: · Dimensions (W x L x H approx.): Pace1PRM: 3.5" x 3.5" x 1" (88.9mm x 88.9mm x 25.4mm). * See note on Page 3. Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. Pace1PTM and Pace1PRM are not intended to be connected to outside plant leads and should be installed indoors within the protected premises. Pace1PRM and Pace1PTM are intended for indoor use only. 1. Pace1PRM installation: a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit's mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet switch/network, NVR or video server. b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked [PoE Input] (Fig. 2, pg. 3). c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 Link] (Fig. 2, pg. 3). UTP: Connect UTP to connector marked [UTP Link] (Fig. 2, pg. 3). 2. Pace1PTM installation: a. Secure unit to desired mounting surface with a proper fastening device utilizing the case's mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device. b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3). c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 Link] (Fig. 2, pg. 3). UTP: Connect UTP to connector marked [UTP Link] (Fig. 2, pg. 3). 3. Pace1ST installation: a. Secure unit to desired mounting surface with a proper fastening device utilizing the case's mounting hole (Fig. 3a, pg. 3). Unit should be mounted in the proximity of camera/device. b. Connect structured cable from IP camera/device to RJ45 jack marked [IP Device] (Fig. 3, pg. 3). c. Connect CAT5e or higher to the connector marked [Pace Receiver] from receiver (Pace1PRM) (Fig. 3, pg. 3). Parameter Connections Input power requirements Indicators Environmental Conditions Technical Specifications: Description RJ45 for ethernet link or single pair UTP. Midspan or endspan port connected. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W) Yellow (RJ45 connector): Green (RJ45 connector): Green: On - Link, Off - No Link, Blinking - Activity. On - 100Base-TX, Off - 10Base-T. PoE Active. Operating Ambient Temperature (UL60950-1): Pace1PRM: 20ºC to 49ºC ( 4ºF to 120.2ºF). Pace1PTM: For 15W: 40ºC to 75ºC ( 40ºF to 167ºF). For 25W: 40ºC to 70ºC ( 40ºF to 158ºF). For 30W: 40ºC to 60ºC ( 40ºF to 140ºF). Pace1ST: For 15W: 40ºC to 75ºC ( 40ºF to 167ºF). For 30W: 40ºC to 49ºC ( 40ºF to 120ºF). Relative Humidity: 20 to 85%, non-condensing. Storage Temperature: 40ºC to 75ºC ( 40ºF to 167ºF). Operating Altitude: 304.8 to 2,000m. Regulatory Compliance Weights (approx.) UL/CUL Listed for Information Technology Equipment (UL 60950-1). CE European Conformity. C-Tick compliant. Product: 0.25 lb. (0.11 kg) | Shipping: 0.42 lb. (0.19 kg). - 2 - Pace1PRM Installation Guide Fig. 1 Pace1PRM Single UTP from Structured Cable Pace1PTM to Midspan/Endspan Pace1PTM Single UTP Structured Cable from from Pace1PRM Camera/Device CAT5 or higher from Pace1PTM Green LED indicates PoE being transmitted to Pace1PTM Green LED indicates PoE Present from Midspan/Endspan CAT5 or higher from Pace receiver Green LED indicates PoE received from Pace1PRM Green LED indicates PoE transmitted to Camera/Device *Note: Caution: once PoE connection is established between Pace1PRM and Pace1PTM (Pace1ST), disconnection from Pace1PTM (Pace1ST) will not disable the PoE output voltage on the Pace1PRM, although the Pace1PTM (Pace1ST) can be reconnected, caution should be taken not to connect the CAT5e or single UTP wiring from Pace1PRM to any non-PoE device. Single PoE Camera Connection Utilizing Pace1PRM and Pace1PTM: Fig. 2 Fig. 2a Pace1PRM Pace1PTM Mounting Hole Pace1PRM - Receiver IP-UTP Receiver Passes PoE/PoE+ RJ45 LEDs Yellow - Activity Green - Speed Green LED Power and PoE I.T.E. 43KC UTP Link Z1409 www.altronix.com Output Input RJ45 PoE PoE PoE Link LED Input LED IP-UTP TRANSCEIVER Transceiver Passes PoE/PoE+ RJ45 LEDs Yellow - Activity Green - Speed Green LED Power and PoE I.T.E. 43KC UTP Link Z1409 www.altronix.com Input RJ45 PoE Link LED Output PoE PoE Out LED PoE Camera PoE+ over CAT5e up to 500m max. 100m max. Powered Switch or NetWay MidSpan PoE compliant 100m max. Legend: Structured Cable Single PoE Camera Connection Utilizing Pace1PRM and Pace1ST: Fig. 3 Pace1PRM Mounting Hole Pace1PRM - Receiver IP-UTP Receiver Passes PoE/PoE+ RJ45 LEDs Yellow - Activity Green - Speed Green LED Power and PoE I.T.E. 43KC UTP Link Z1409 www.altronix.com Output Input RJ45 PoE PoE PoE Link LED Input LED Fig. 3a Pace1ST Pace1ST - Transceiver Supports PoE/PoE+ RJ45 LEDs Green LED Yellow - Speed Green - Activity Power and PoE I.T.E. 43KC Pace Receiver www.altronix.com PoE Out IP Device PoE Camera PoE+ over CAT5e up to 500m max. 100m max. Powered Switch or MidSpan Pace1PRM Installation Guide PoE compliant 100m max. Legend: Structured Cable - 3 - Fig. 4 Multiple PoE Cameras Connection: Pace1PRM 100m max. Pace1PRM 100m max. Pace1PRM 100m max. Pace1PRM 100m max. PoE+ over CAT5e up to 500m max. or Single UTP up to 153m max. PoE+ over CAT5e up to 500m max. or Single UTP up to 153m max. PoE+ over CAT5e up to 500m max. or Single UTP up to 153m max. PoE+ over CAT5e up to 500m max. or Single UTP up to 153m max. PoE Pace1PTM or compliant Pace1ST 100m max. PoE Pace1PTM or compliant Pace1ST 100m max. PoE Pace1PTM or compliant Pace1ST 100m max. PoE Pace1PTM or compliant Pace1ST 100m max. PoE Camera PoE Camera PoE Camera PoE Camera Powered Switch or NetWay MidSpan Legend: Structured Cable or Single UTP Maximum Length of CAT5e Type or UTP vs. Camera Power/PoE Class: Camera Power/PoE Class 13W/0 4W/1 6.5W/2 13W/3 25W/4 Single UTP - 23AWG (Pace1PTM) CAT5 or Higher (Pace1PTM & Pace1ST) Max. Length (meters) 153 500 153 500 153 500 153 500 153 423 Note: Higher gauge wiring will allow for longer distances. Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIPace1PRM Rev. 111413 I08U MEMBER - 4 - Pace1PRM Installation Guide