AF930 Instructions

Product Accessories (Optional)

Host

[Image of Host device]

Type-C Charging cable

[Image of Type-C charging cable]

Instructions

[Image of instruction manual icon]

8. Contactless card reader

9. Front-placed camera

10. Flashlamp

11. Indicator light

12. Custom function keys

13. The volume key

14. Headphone hole

15. USB charging interface

16. Printer

17. Rear-placed camera

18. SIM, PSAM Cardslot (Internal)

19. Flashlight

20. Battery

21. External speakers

[Image of the back and side views of the POS device with numbered components]

I. IC card operation mode

Insert IC card, please insert IC card chip up and the arrow shown in the right head direction. Insertion POS Machine.

II. Operation mode of magnetic stripe card

When swiping the card, please stick the magnetic strip card in the slot. Brush smoothly from top to bottom.

III. Flash QuickPass Card operation mode

Please hold the card face horizontally. Close to equipment according to map position.

[Image illustrating the three operation modes: IC card insertion, magnetic stripe swiping, and contactless card proximity]

I. Safety Precautions

1. The use of any potentially explosive gases is strictly prohibited.
2. Avoid installation or use during lightning; otherwise, there is a risk of lightning electric shock.
3. Turn off the power supply immediately when you find abnormal odor, overheat or smoke.
4. Storage temperature: -20°C to 45°C, Operating temperature: -10°C to 45°C. Humidity: ≤95%.

II. Points for Attention in Daily Use

1. Do not use in close water or humid environment to avoid liquid falling into POS machine.
2. Do not use in extreme cold or hot environments, such as cigarettes near fire or ignited.
3. Don't fall, throw or bend.
4. Use in a clean and dustless environment as far as possible to avoid small items falling into POS machine.
5. Do not use near medical equipment without permission.
6. Do not use it on aircraft or in any other place where radio communication is prohibited.
7. The model approval code of this product is displayed on the product appearance nameplate.

• Q: PS charging, the use time is obviously shortened?
  A: 1. When POS is abnormal in use or when low power is prompted, please charge the equipment. It is recommended to charge each time. At least 3.5 hours.
• Q: PS is unsuccessful in reading magnetic cards or has a low success rate in reading magnetic cards?
  A: 1. Use one or more different magnetic stripe cards for transaction testing to ensure that the problem is not caused by magnetic stripe cards.
• Make sure the card brushing posture is correct and the card is smoothly brushed through the chute during the whole process.
• You can try different speeds of swiping cards.
• Q: Unable to read IC card information?
  A: 1. Check whether the insertion direction of IC card is correct.
• The metal contact surface of IC card reader is contaminated with impurities. Please clean and try again.
• IC card is damaged, a new IC card is used to check whether it is an IC card problem, if it is an IC card problem, please change the new card.

Product name: WirelessPOS

Product type: AF930

Guarantee Item:

1. We have a set of complete after-sales service system in accordance with ISO9001 Quality Management System.
2. We will charge the maintenance fee if the damage caused by human factors. Please keep this card properly for your warranty.
3. Please keep this card properly for your warranty.

Manufacturer's contact information

Manufacturer: Beijing Shenzhou Anfu Technology Co.,Ltd

Product certificate

Inspector: Pass 1

Manufacturer: Beijing Shenzhou Anfu Technology Co.,Ltd

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of this Device AF930 (2BLHD-AF930) has been tested against this SAR limit. SAR information on this can be viewed on-line at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search. This device was tested for typical operations 0mm from the body. To maintain compliance with FCC RF exposure requirements, 0mm separation distance should be maintained to the user's bodies.

4006838160

www.anfupos.com

WirelessPOSAF930 Instructions

[Image of the AF930 Wireless POS Terminal]