User Manual for ZEBRA models including: Aurora MV FIS Configuration Utility, Aurora MV, FIS Configuration Utility, Configuration Utility
Page 7 of 8 V1.134.0001 – Initial Product Release RELEASE DATE: JULY 2021 • Bug Fixes • Stability Improvements Components SW Component Version InstallShield 5.0.13000 Aurora™ 5 .0 13 BSP (xS40/70) CAAESS00-002-R06
Zebra Aurora Focus™ Software | Zebra
Zebra AuroraTM MV/FIS Configuration Utility Description Product Description Zebra AuroraTM is a host-side application which allows for the configuration Zebra FS10, xS20, xS40 and xS70 devices. Device Compatibility Zebra AuroraTM can be used to program Zebra MV/FIS devices through these programming modes: · USB connected cable · M12 Ethernet Supported Devices FS40, VS40, FS70, VS70 FS10, FS20, VS20 Supported Device FW CAAESS00-002-R06 CAAFFS00-002-R06 Release Notes This document summarizes the following software release: Software Version Number V5.0.13000 Release Date February 2023 V5.0.13000 RELEASE DATE: FEBRUARY 2023 · Technology Previews o Aurora and HMI Language Support Simplified Chinese, Korean, German, French and Spanish o Expanded ZETI Interface Commands · Tools Page 1 of 8 o Deep Learning Based OCR for Fixed Industrial Scanners Fully Released Activated via Licenses · Performance o Improvements to deployed job run consistency including Barcode tool timeout, decoding, and trigger timing consistency. o Level Trigger Enhancements o Triggered Image Buffering · UX Improvements o Backup/Restore/Firmware Upgrade in Aurora · Device Configuration 1D Parameter Barcode Setup Known Issues · Rarely, a barcode tool can sometimes fail on certain images if it follows a machine vision tool. o Resolution: Move barcode decode tool to run before the machine vision tool. · When viewing a circle tool that failed in the HMI, it will sometimes cause the HMI to not refresh and will display a blank page. o Resolution: Use Aurora to inspect the details of a failing circle tool. · When a user needs to change a device USB IP address, they must first disable the DHCP server option and then re-enable it again afterwards. · When executing the ZETI command `Trigger with result', after using the `Deploy Job', the trigger command can sometimes fail. o Resolution: Add a 2 second delay or more after the `Deploy Job' command. · When using ZETI, any command that has a job slot option, the job slot must be specified for this release. · The ZETI command line `help' command is not complete. Please refer to ZETI documentation for comprehensive overview of the command set · When in Edit mode in Aurora, setting the GPIO Hardware Trigger falling edge can cause the trigger to use the rising edge instead. o Resolution: Set the edge back to rising and then back to falling in the drop-down menu. · If a device is added to Aurora by IP address, the Aurora Firmware Dual Update will not complete the Dual Update. o Resolution: Use HMI if Dual Update is required. Page 2 of 8 · Flaw detection tools have to click `Undo' twice to perform the undo operation. · When using Aurora for viewing a running barcode job, sometimes decode summary will fail to get updated. o Resolution: Close the job being viewed and reopen the job again in view mode. · Device will sometimes not be discoverable in Aurora when starting firmware update in HMI. Device will re-appear once the firmware update completes and reboots · After updating the firmware, some jobs will not be able to be changed using the HMI. o Resolution: Run "User Settings" reset in HMI (must be admin) · Rarely, the HMI may not appear through the display port unless the device is rebooted. · Autotune will sometimes fail at a range of ~200mm on 2D barcodes only, if illumination is off o Resolution: Ensure adequate light is available, either with continuous light or enabling the LED lights on the device. · When generating a backup, if done after setting the time zone, the backup may fail. o Resolution: Reboot device after time zone change if planning to backup. · When setting the TCP Heartbeat string in Aurora, nonstandard ASCI characters may cause the heartbeat to not be sent. o Resolution: Ensure any heartbeat string the user defines uses standard ASCII characters only · When reordering tools in Aurora that have dependencies on other tools, the reordered tool may not be able to be edited. o Resolution: Remove and re-add the tool back to the workflow. · Certain special characters in a job name cause the job results image folder to not allow download from the device. o Resolution: Use only standard characters for job names · In some cases, using large number of image banks cause slight delays in processing. · After upgrading the device firmware, USB options may be grayed out. o Resolution: Perform User Setting Reset from HMI and update device settings after. · Firmware update will fail if memory consumption is already high. o Resolution: Reboot the device and upgrade · Uninstalling the InstallShield does not always remove all registry entries. o Resolution: regedit and manually delete Aurora folder under Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Zebra Page 3 of 8 Release Notes (Previous Releases) V4.0.22000 RELEASE DATE: DECEMBER 2022 · Added Measure Object Tool · Added Flaw Detection Edge and Intensity Tools · Added Object Locate Counting · Added Image Filters: Gradient, Gradient Horizontal, Vertical and Full · MV Output Formatting on Supported Interfaces (Global or Interface Specific) · Added Find and Replace to Barcode Decode Tool · Improved 1D/2D Barcode Decode Performance · Setting Barcode Match String via TCP or Serial input · Added Image Download Capability via HMI · Enhanced Session Based Triggering for Level, Continuous and Presentation Triggers w/Exit Criteria/Aggregation · Technology Preview: Device Backup/Restore Functionality · Performance and Stability Enhancements V3.1.40000 RELEASE DATE: AUGUST 2022 · Added Reset on Trigger for Do Note Read Same Barcode · Spanish HID Keyboard support · Performance and Stability Enhancements V3.0.10000 RELEASE DATE: JUNE 2022 · Added Edge Counting · Added Deep-Learning Based OCR Tool (in Beta) · Added Circle Find Tool · Added Circle Diameter Measurement Tool · Added a Circle ROI Type · Added Open and Close Filters · Added Erode Filter Page 4 of 8 · Added RS-232 Input Trigger · Additional 2D Barcode Performance Improvements · Added ADF to include Pass/Fail Data Types · Added ADF to include Barcode Quality Metrics Data · Performance and Stability Enhancements V2.0.8000 RELEASE DATE: APRIL 2022 · Performance and Stability Enhancements V2.0.7000 RELEASE DATE: MARCH 2022 · Performance and Stability Enhancements · 1D Barcode Quality Metrics · Added Object Locate Plus · Added Blob Tools · Added Binarize Filter/Tool · Added Dilate Filter/Tool · ImagePerfect(+) fixes & improvements · Added Scale Calibration for Distance tool · Added Advanced Pass/Fail Configuration (AND/OR logic for Job results) · HID Keyboard Expansion added French and German KB · Added support for Codabar symbology · Added Encoding type (Text/Base64) for ADF Full String data type and added option to show non- printable characters as hex values · For xS10/20, added external illumination support · Added "File Path" option when using (S)FTP to Save images · Added Ability to Open a Local Job (created with emulator) On a Real Connected Camera V1.200.2001 RELEASE DATE: DECEMBER 2021 · Performance and Stability Enhancements Page 5 of 8 · Support for 5MP xS40 and xS70 models · ImagePerfect(+) for FS models · Option to output Barcode Location Co-ordinates · Option to not read last n number of barcodes · Device can be a TCP/IP Client · Configurable RS-232 settings · Ability to configure GPIO Trigger delay · Support for Fast Hardware Trigger (2.3 MP models only) · Ability to set GPIOs to static high or low · Added Job controls to clone, rename and delete jobs · Support for Conditional Regular expressions for Barcode String Match · Barcode String Match Regular expression support for ManyCode · Backwards compatibility of Job files · Decode and MV statistics in Aurora and HMI stored and queried from device V1.148.0001 RELEASE DATE: OCTOBER 2021 · Performance Enhancements · Stability Improvements · Implementation of licensing error messages in Web HMI · Fixed issue of Job pausing on refresh of Web HMI · Fixed issue of crash when clicking on "Communications" tab · Fixed inability to "View" active Jobs from Job menu when Job utilizes a trigger that is automatic in nature. · Fixed issue of slow decode rate when "Fast 1D/2D" license is enabled · Added Configurable TCP/IP results port and trigger string can be configured · Support for GPIO > Hardware trigger (normal speed) · Allow setting a job as Startup / Power up job · Emulators now have license level · Supports a total of 21 emulators · ZJOB backwards compatibility and auto conversion of old job files (Windows only) · Seamless (live) tool changes when Upgrade licenses are applied Page 6 of 8 V1.134.0001 Initial Product Release RELEASE DATE: JULY 2021 · Bug Fixes · Stability Improvements Components SW Component Version InstallShield 5.0.13000 AuroraTM 5.0.13 BSP (xS40/70) CAAESS00-002-R06 BSP (FS10/xS20) CAAFFS00-002-R06 AuroraTM HMI 2.1.00 The components are installed in the following folders: Component Location Application Program Files\Zebra Technologies\Aurora Job/Configuration Users\Public\Documents\ZebraAurora\xSx0\Jobs Files Saved Images Users\Public\Documents\ZebraAurora\Captures\xSxxxxxx Camera Page 7 of 8 Minimum PC Requirements Component Location CPU Intel or AMD 64-bit processor Random Access 4 GB | Recommended: 8GB Memory Files GPU GTX 1030, Intel UHD 620 or equivalent Graphics Memory 2GB | Recommended: 4GB Disk Space 4GB free disk space Monitor Resolution 1280 x 800 | Recommended: 1920 x 1080 Operating System Windows 10 Internet Connection Required for software activation Installation AuroraTM can be launched from the Windows 10 Start button. · Start / All Programs / Zebra Scanner / Zebra Aurora Page 8 of 8Microsoft Word for Microsoft 365