Instructions for ELEVATE models including: 2BC24-P5, 2BC24P5, Prototype P5, Prototype P5 Telematic VCU Microcontroller, Telematic VCU Microcontroller, VCU Microcontroller, Microcontroller
The Techno Creatives P5 Elevate Telematic Unit 2BC24-P5 2BC24P5 p5
P5 Elevate Telematic Unit by The Techno Creatives
Telematic unit Prototype P5 (WIP) Description The device serves as a telematic unit with an integrated general purpose VCU microcontroller. Interfacing with the vehicle through a 18 pin connector. Features - Wide range supply voltage (6-60V) - Inbuilt Cellular and GNSS antenna. - Inbuilt backup battery - x6 GPIOs - x2 CAN interface - 512Mb flash memory - Accelerometer - Temperature sensor - Tamper detection for lid and connector removal - LED status indication - Water protected housing and connectors - Extra general purpose VCU for business applications - Sleep modes (Low and high frequency mode, Deep sleep) - Programmable through connector or OTA Specifications Supply voltage Backup battery: Temperature range 8-60V VDC Lipo 1800mAh (6.66Wh) -40°C to +85 [RADIO SPEC WHEN AVAILABLE] [CONSUMPTION SPEC WHEN AVAILABLE] GPIO(1-5) pins AIN IM_OUT GNSS antenna Cellular antenna LED indications SIM Memory Memory 2xCAN 3V3 digital input / output, (12V input tolerant) Analog input 0-100V Digital output 3V3 PCB mounted ceramic high gain antenna. Internal PCB GSM High Gain GNSS, CELL, FAULT Nano-SIM 512Mb flash memory for VCU 64Mb flash memory for OTA ISO-11898-5, 1Mb/s LTE CAT-M1 Cellular bands GNSS 850 / 900 / 1800 / 1900 MHz GPS, GLONASS, BEIDOU Dimensions CHANGE TO LATEST DESIGN Connector pinout 1 VDC 2 CAN_H 3 CAN_L 4 CAN_H 5 CAN_L 6 IM_OUT 7 GPIO_5 8 GPIO_1 9 TAMPER_CONN 10 NRF_SWDIO 11 NRF_SWCLK 12 VCU_SWDIO 13 VCU_SWCLK 14 GPIO_2 15 GPIO_3 16 GPIO_4 17 AIN_100V 18 GND 12V (6V-60V) 250 baud 250 baud 500 baud 500 baud Immobilizer output Battery temp input Immobilizer output Connector tamper detection Programmer data pin (NRF) Programmer clock pin (NRF) Programmer data pin (VCU) Programmer clock pin (VCU) GPIO_2 GPIO 4 GPIO 3 Analog input (max 100V) Ground pin FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.macOS Version 13.3.1 (a) (Build 22E772610a) Quartz PDFContext