User Guide for NODON models including: P1899, ZIGBEE Multifunction Relay Switch Pro
8 apr 2021 —
ON ON ON INSTALLATION - PRISE ÉLECTRIQUE MODE IMPULSIONNEL Il est impératif d'activer le mode impulsionnel avant d'appairer votre module à votre centrale domotique pour piloter votre portail/
File Info : application/pdf, 2 Pages, 3.43MB
DocumentDocumentFR MODE D'EMPLOI MODULE MULTIFONCTION PRO ZIGBEE Référence : SIN-4-1-20_PRO Alimentation : 230V AC ~ 50Hz Capacité de commutation : 230V AC - 16A Consommation : <1W Puissance Max. : 3680W - Zéro crossing intégré Protocole radio : Zigbee 3.0 Bande de fréquences utilisée : 2,4Ghz Puissance radio maximale : +10dBm Portée : Jusqu'à 40m en intérieur Température de fonctionnement : -20°C à 60°C Indice de protection : IP 20 Dimensions : 40 mm (l) x 44 mm (L) x 16.9 mm (h) Poids : 34 g Garantie : 5 ans PRÉCAUTIONS D'USAGES · N'utilisez jamais l'appareil s'il n'est pas correctement installé et placé à l'intérieur d'une boite de raccordement conforme aux normes en vigueur. · Tenez le produit éloigné de tous liquides. NOTICE DÉTAILLÉE Accédez directement à la notice détaillée sur www.nodon.pro CONTACT NodOn SAS 121 rue des Hêtres 45590 St CYR EN VAL (FRANCE) SAV www.nodon.pro support@nodon.pro APPROBATIONS ET CERTIFICATIONS Par la présente, NodOn SAS déclare que cet équipement radio est conforme à la directive RED 2014/53/UE. Le texte intégral de la déclaration de conformité de l'UE est disponible à l'adresse Internet suivante : www.nodon.pro section « Support » La présence de ce symbole sur un produit indique que ce dernier est conforme à la directive européenne 2012/19/UE. Renseignez-vous sur les dispositions en vigueur dans votre région concernant la collecte séparée des appareils électriques et électroniques. Respectez les réglementations locales et ne jetez pas le produit avec les ordures ménagères ordinaires. La mise au rebut correcte d'anciens produits permet de préserver l'environnement et la santé. Ce produit est prévu pour être utilisé en intérieur uniquement. Ce produit est conforme au protocole radio Zigbee. GARANTIE La garantie débute à partir de la date de fabrication de votre produit (MM/AA). Cette date est visible sur le sticker au dos de votre produit : DANGER D'ÉLECTROCUTION AVANT T O U T E I N S TA L L AT ION ASSUREZVOUS D'AVOIR COUPÉ L' ALIMENTATION ÉLECTRIQUE SOUS PEINE D'ÉLECTROCUTION. Coupez directement l'alimentation depuis le coffret électrique, pour éviter tout risque d'électrocution. Ce module est conçu pour une utilisation sous tension, une mauvaise installation peut entraîner un incendie ou un choc électrique. Si vous ne vous sentez pas à l'aise avec les installations électriques, veuillez consulter un professionnel. Le module doit obligatoirement être installé ET connecté en suivant scrupuleusement les instructions de cette notice. Nous ne pourrons être tenus pour responsables en cas d'accident ou de dommages dus au non respect des instructions de montage. Coupez l'alimentation avant toute intervention et n'effectuez aucune modification si la LED est allumée. INSTALLATION Grâce à sa taille réduite, le Module Multifonction Zigbee s'installe dans une boîte de raccordement ou derrière un interrupteur, une prise électrique, ou une sortie de câble. ASTUCE Ajoutez tableau le Module électrique MavuelctifleonBcotiitoinerZRigabileDeINau* NodOn. *Accessoire en option ENTRÉES / SORTIES DU MODULE N Entrée Neutre L Entrée Phase Entrée pour l'interrupteur filaire (I1)* Non utilisé Borne d'entrée, le potentiel transitera vers la borne de sortie Borne de sortie Chaque borne doit être raccordée par un câble de section comprise entre 1.5mm² et 4mm² dénudé de 8mm. *Interrupteur filaire en option (voir www.nodon.pro/support) INSTALLATION - PORTAIL / PORTE DE GARAGE / GÂCHE ÉLECTRIQUE - CONTACT SEC IMPULSIONNEL ON Figure 1 1 Coupez le courant. 2 Démontez le poussoir qui pilote le portail/porte de garage/ gâche électrique. 3 Câblez le module multifonction, en parallèle du poussoir selon le schéma figure 1. 4 Remontez le poussoir qui pilote le portail/porte de garage/ gâche électrique. 5 Remettez le courant. Attention : Activez le mode impulsionnel (voir rubrique) avant l'appairage sous peine d'endommager votre équipement. MODE IMPULSIONNEL Il est impératif d'activer le mode impulsionnel avant d'appairer votre module à votre centrale domotique pour piloter votre portail/ porte de garage/gâche électrique sous peine d'endommager votre équipement. Le module doit être raccordé et sous tension. 1 Effectuez 5 appuis consécutifs rapides sur le bouton du module. La LED scintille en vert, confirmant l'activation du mode commande d'accès. 2 Vous pouvez reprendre la procédure d'installation. Note : Pour désactiver le mode impulsionnel, recommencez une série de 5 appuis rapides consécutifs. INSTALLATION - PRISE ÉLECTRIQUE ON Figure 2 1 Coupez le courant. 2 Démontez la prise électrique et l'interrupteur. 3 Câblez le module multifonction selon le schéma figure 2. 4 Remontez la prise électrique et l'interrupteur. 5 Remettez le courant AUTO-DÉTECTION DU TYPE D'INTERRUPTEUR Lorsque que vous allumez l'alimentation électrique (via le coffret électrique par exemple) une fois le module installé, il est nécessaire de faire une action simple (Un appui unique) sur l'interrupteur filaire. Une détection automatique du type d'interrupteur (Monostable ou bistable) sera alors effectuée. INSTALLATION - CHAUDIÈRE - CONTACT SEC TENU ON Figure 3 1 Coupez le courant. 2 Démontez la sortie de câble. 3 Câblez le module multifonction selon le schéma figure 3, en prenant soin de raccorder les 2 fils de pilotage du thermostat d'ambiance (voir notice de la chaudière). 4 Remontez la sortie de câble. 5 Remettez le courant. SCHÉMAS DE CÂBLAGE Retrouvez tous les schémas de câblage dans l'espace PRO sur www.nodon.pro AJOUT AU RÉSEAU ZIGBEE Lors de la mise sous tension, la LED du module clignote en orange cherchant à joindre un réseau Zigbee. Rendez-vous dans l'application de votre centrale Zigbee pour activer la détection du module. Voir la liste des centrales domotiques compatibles sur www.nodon.pro Si le module a correctement rejoint le réseau, la Led devient verte. Le module est prêt à être utilisé. Si module n'a pas rejoint un réseau dans les 15 minutes, la LED devient orange. Faites un appui rapide sur le bouton du module et recommencez la procédure. DÉSAPPAIRAGE DU MODULE Pour supprimer le module de son réseau, faites un Reset du module (voir "procédure de réinitialisation du Module"). PROCÉDURE DE RÉINITIALISATION DU MODULE Le module doit être raccordé et sous tension. 1 Appuyez plus de 5 secondes sur le bouton du module. La Led scintille en orange. 2 Appuyez à nouveau sur le bouton (impulsion brève) pour valider la réinitialisation. Si la réinitialisation se déroule correctement, la Led clignote alternativement en rouge et en vert, puis clignote en orange. Recommencez si nécessaire. 3 Votre module a retrouvé sa configuration d'origine et est prêt a rejoindre un nouveau réseau Zigbee. EN USER GUIDE ZIGBEE MULTIFUNCTION RELAY SWITCH PRO Reference: SIN-4-1-20_PRO Power supply: 230V AC ~ 50Hz Switching capabilities: 230V AC - 16A Consumption: <1W Max. Power: 3680W - Integrated Zero crossing RF Protocol: Zigbee 3.0 Radio frequency range: 2.4Ghz RF power Max: +10dBm Range: up to 40m indoor Operational temperature: -20°C to 60°C Protection rating: IP 20 Dimensions: 40 mm (l) x 44 mm (L) x 16.9 mm (h) Weight: 34 g Warranty: 5 years USE CAUTIONS · Never use the device if it is not correctly installed and placed inside a connecting box in conformity with the current norms. · Keep the product far away from liquids. DETAILED USER GUIDE Directly access the detailed user guide on www.nodon.pro/en CONTACT NodOn SAS 121 rue des Hêtres 45590 St CYR EN VAL (FRANCE) SAV www.nodon.pro/en support@nodon.pro APPROVALS AND CERTIFICATIONS Hereby, NodOn SAS declares that this radio equipment is conform to the RED directive 2014/53/UE. The integral text of the EU declaration of conformity is available at the following online address: www.nodon.pro "support" section. The presence of this symbol on a product indicates that this one is conform to the European directive 2012/19/UE. Find out more about the provisions in force in your region regarding the separate collection of electrical and electronical devices. Respect the local rules and do not throw out the product with common domestic wastes. The correct rejection of ancient products allows to preserve the environment and health. This product must be used indoor only. This product is conform to Zibgee radio protocol. WARRANTY The warranty begins from the date of manufacture of your product (MM/YY). This date is visible in your product back sticker: : DANGER OF ELECTROCUTION BEFORE ANY INSTALLATION MAKE SURE THE POWER SUPPLY IS DISCONNECTED TO AVOID ANY RISK OF ELECTROCUTION. Directly cut the power supply from the breaker box to avoid any risk of electrocution. This relay switch is designed to be used power up, a wrong installation can create a fire or an electric shock. If you are not confident about electrical installation, please ask a professional. The relay switch must be installed and connected carefully following the instructions of this user guide. We will not be responsible for any loss or damage resulting from a nonrespect of the instructions of this user guide. Cut the power supply before any operation and don't do any modification if the LED is still ON. INSTALLATION Thanks to its compact size, the Multifunction Relay Switch can be installed behind a wall switch, an electrical outlet or a cable outlet. INSTALLATION - GATE/GARAGE DOOR/ ELECTRIC LATCH - IMPULSE MODE DRY CONTACT ON Figure 1 1 Cut the power supply 2 Disassemble the push-button which controls the gate/ garage door/electric latch. 3 Wire the Multifunction Relay Switch, in parallel to the pushbutton following the diagram figure 1. 4 Reassemble the push-button which controls the gate/ garage door/electric latch. 5 Turn the power back ON. Warning: Activate the implulse mode (see the section) before pairing to avoid any damage of your equipment. IMPULSE MODE It is imperative to activate the impulse mode before pairing your module to your home automation gateway to control your gate/garage door/electric latch to avoid damaging your equipment. Relay switch must be power supplied. TIP Add the electric Multifunction Relay Switch panel with NodOn DIN Rail Btootxh*e. *Optional accessory RELAY SWITCH INPUT/OUTPUT N Terminal for the Neutral L Terminal for the Line Input terminal for the wired switch 1 (I1)* Not used Input terminal, the potential will pass through the output terminal Output terminal Each terminal should be installed with a cable from 1.5mm² to 4mm² maximum, stripped of 8mm. *Wired switch optional. 1 Do 5 brief presses on the button of the relay switch. The LED pulses in green, confirming the activation of the control access mode. 2 You can continue the installation procedure. Note: To deactivate the impulse mode, repeat a series of 5 short presses. INSTALLATION - ELECTRICAL OUTLET ON Figure 2 1 Cut the power supply. 2 Disassemble the electrical outlet and the wall switch. 3 Wire the Multifunction Relay Switch, following the diagram figure 2. 4 Reassemble the electrical outlet and the wall switch. 5 Turn the power back ON. AUTO-DETECTION OF SWITCH TYPE When you turn the power supply ON (via the electrical box for example) once the relay switch is installed, it is necessary to perform a simple action (single press on the button) on the wired switch. Automatic detection of the type of switch (monostable or bistable) will then be performed. INSTALLATION - BOILER - HELD DRY CONTACT ON Figure 3 1 Cut the power supply. 2 Disassemble the cable outlet. 3 Wire the Multifunction Relay Switch following the diagram figure 3, making sure to connect the two wires which controls the ambient thermostat (see your boiler user guide). 4 Reassemble the cable outlet. 5 Turn the power back ON. INSTALLATION DIAGRAMS Find all the installation diagrams in the PRO area on www.nodon.pro/en ADDING TO A ZIGBEE NETWORK When power is turned ON, the relay switch Led will blink orange, looking to join a Zigbee network. Go to your Zigbee gateway app to activate the relay switch detection. See the compatible home automation gateways on www.nodon.pro/en If the relay switch has correctly joined the network, the Led becomes green. The relay switch is ready for use. If the relay switch hasn't joined a network within 15 minutes, the Led becomes orange. Do a brief press on the relay switch button and start again. UNPAIRING PROCEDURE To remove the module from its network, perform a Module Reset (see "Reset Procedure"). RESET PROCEDURE Relay switch must be power supplied. 1 Press more than 5 seconds on your module's button. The Led blinks orange. 2 Press the button again (short press) to validate the reset. If the reset is successful, the Led flashes red and green alternately, then flashes orange. Repeat if necessary. 3 Your module has returned to its original configuration and is ready to join a new Zigbee network. SIN-4-1-20_PRO-UG-V1Adobe PDF Library 15.0 Adobe InDesign 16.0 (Windows)