User Manual for audio-technica models including: Omnidirectional Condenser Boundary Microphone, ES945O, FM5
User Manual. English. Safety precautions.
ES945O/FM5. Omnidirectional Condenser Boundary Microphone. User Manual. English. Page 2. 1. Although this product was designed to be used safely, failing ...
©2021 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 株式会社オーディオテクニカ 〒194-8666 東京都町田市西成瀬2-46-1 www.audio-technica.co.jp. Title: ES945O/FM5 User Manual Author: Audio-Technica Corporation Created Date:
File Info : application/pdf, 11 Pages, 1.08MB
DocumentDocumentES945O/FM5 Omnidirectional Condenser Boundary Microphone User Manual English Safety precautions Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product. Cautions for the product · Do not subject the product to strong impact to avoid malfunction. · Do not disassemble, modify or attempt to repair the product. · Do not handle the product with wet hands to avoid electric shock or injury. · Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place. 1 Notes on use · Do not swing or pull with the cable connected to the microphone to prevent the microphone from becoming disconnected or damaged. · Do not wind the cable around the rack or allow the cable to become pinched. · The microphone should be placed on a flat, unobstructed mounting surface. · Placing any object on a surface (such as a conference table) before its finish is fully cured may result in damage to the finish. 2 Using the product Included accessories 1 2 3 1 Rubber isolator (1) 2 Rubber isolator (2) 3 Nut 3 Using the product How to mount the product Table/ceiling hole size (when using isolators) 23.5 (Unit: mm) Table/ceiling hole size (when not using isolators) 20.5 (Unit: mm) Example: Mounting on a table 1 4 2 3 1 Rubber isolator (1) 2 Rubber isolator (2) 3 Nut 4 Table 4 Using the product Switch setting and functions 5 1 MIC Contact Closure 4 GND 2 1. Action 2. Contact closure status 3. Audio status 4. LED color 5. LED status LED color 1 2 3 OFF RED GREEN YELLOW 4 BLUE 5 MAGENTA 6 CYAN 7 WHITE 5 Using the product Connection procedure The output connector is an XLR-M type with polarity as shown in the figure below. 1 5 2 4 3 1 PIN1 (ground) 2 PIN2 (hot) 3 PIN3 (cold) 4 Contact closure 5 LED control 6 48 84.8 Dimensions 38 20.6 M20 P=1 (Unit: mm) 7 70.3 Specifications Element Fixed-charge back plate, permanently polarized condenser Polar pattern Omnidirectional Frequency response 60 to 15,000 Hz Open circuit sensitivity -33 dB (0 dB = 1 V/Pa, 1 kHz) Impedance 60 ohms Maximum input sound level 130 dB SPL (1 kHz at 1% THD) Dynamic range 109 dB (1 kHz at Max SPL) Signal-to-noise ratio 73 dB (1 kHz at 1 Pa, A-weighted) Phantom power requirements 11-52 V DC, 6.8 mA Weight 59 g (2.1 oz) Dimensions 38 mm (1.50") × 48 mm (1.89") × 84.8 mm (3.34") (W × D × H) Output connector Integral 5-pin XLR-M type Included accessories Rubber isolator (2 types), Nut · 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL · For product improvement, the product is subject to modification without notice. 8 Polar pattern/Frequency response Polar pattern 0° 330° 300° 30° 60° 270° 90° 240° 120° LEGEND 210° 180° 150° 200 Hz 1 kHz 5 kHz 8 kHz SCALE IS 5 DECIBELS PER DIVISION Response in dB Frequency response 60 - 15,000 Hz 10 dB 20 50 100 200 500 1k 2k 5k 10k 20k LEGEND Frequency in Hertz 0°, 50 cm 9 194-86662-46-1 www.audio-technica.co.jp Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan www.audio-technica.com ©2021 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 142316943-02-01 ver.1 2021.02.01Adobe PDF Library 15.0