Pyle PD1000BT - PD3000BT Wireless BT Home Theater Preamplifier

Foreword

Your new Pyle Amplifier provides the power and versatility needed for a professional sound system. Its wide frequency response makes it suitable for amplifying music or vocal program material. It can be used in meeting halls, homes, restaurants, schools, stores, or for paging systems.

Please read this manual thoroughly before setting up and using the amplifier. It contains installation suggestions and instructions to ensure safe usage. Installed properly, you can expect years of trouble-free service from this product.

Notices and Disc Protection

Notes on Handling

• The top and rear panels may become warm after extended use; this is not a malfunction.
• When the unit is not in use, remove the disc and turn off the power.
• If the unit will not be used for a long period, it may not function properly in the future. Turn it ON and use it occasionally.
• Do not place foreign objects on the disc tray.

Location

Do not locate the unit in places such as:

• Near heating devices or in enclosed cars.
• High temperature (47°C/116.6°F or higher) or high humidity (90% or higher).
• Dirty places.
• Avoid direct exposure to sunlight.

Disturbance

Placing this unit near a TV, radio, or VCR may result in poor playback picture and distorted sound. In such cases, place the unit away from these devices.

Notes on Moisture Condensation

The pickup may condense with water under the following situations:

• When bringing the unit directly from a cold place to a warm place.
• When using the unit in a room where the heater was just turned on, or where cold air from an air conditioner directly hits the unit.
• During summer, when using the unit in a hot and humid place after moving it from an air-conditioned room.
• When the room is vaporous or damp.

If condensation exists, the unit will not operate properly. Remove the disc, connect the unit's power cord to the wall outlet, turn on the unit, and leave it for two to three hours. This will allow the unit to warm up and evaporate any moisture. Keep the unit connected to the wall outlet; moisture condensation will seldom occur.

On Handling Discs

• Do not touch the playback side of the disc.
• Do not attach paper or tape to the disc.

On Cleaning Discs

• Fingerprints and dust on the disc can cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.
• If dust cannot be wiped off with a soft cloth, lightly moisten a soft cloth and wipe the disc, then finish with a dry cloth.
• Do not use solvents such as thinner, benzine, commercially available cleaners, or antistatic spray for vinyl LPs, as this may damage the disc.

On Storing Discs

• Do not store discs in a place subject to direct sunlight or near a heat source.
• Do not store discs in places subject to moisture and dust, such as a bathroom or near a humidifier.
• Store discs vertically in a case. Stacking or placing objects on discs outside their case may cause warping.

Structure of Disc Contents

Normally, DVD discs are divided into titles, and titles are sub-divided into chapters. Audio CDs are divided into tracks.

• Discs other than those listed above cannot be played.
• Non-standardized discs, even if labeled as above, may not be playable.
• The performance of a recorded disc depends on the method and quality of disc burning. In some cases, the disc may not be played.

Playable Discs and Accessories

Accessories

• Audio/Video cable - 1
• Owner's manual - 1
• Remote control - 1
• AM Antenna - 1 Pc.
• FM Antenna - 1 Pc.
• MP3 Input Cable - 1
• AC Power Cord - 1
• Rack Mounting Brackets with Screws - 2

Playable Discs

Front Panel and LED Function

The front panel features controls for power, input selection, volume, and playback. Key controls include:

• POWER: Turns the unit ON/OFF.
• INPUT: Selects audio sources like DVD/CD/USB, TUNER, IPOD/MP3, AUX.
• MENU CONTROL: Adjusts Master Volume, Bass, Treble, Balance, and Auto Station Seek.
• AM/FM: Selects AM or FM tuning.
• A/B SPEAKERS OUTPUT SELECTOR: Choose between A, B, or A+B speaker outputs.
• TUNING-/TUNING+: Adjusts radio station tuning.
• FUNCTION DISPLAYED FLUORESCENT WINDOW: Displays current function.
• REMOTE SENSOR WINDOW: Receives signals from the remote control.
• OPEN/CLOSE CONTROL: Opens or closes the disc tray.
• PLAY/PAUSE: Controls playback.
• REV, FWD: Fast backward/forward search.
• NUMBER KEYS: Select music tracks or radio stations directly.
• STOP: Stops playback.
• NEXT, PREV: Skips to the next or previous track/song.
• BT ANTENNA: Receives Bluetooth signals.
• BT Signal Indicator: Shows Bluetooth connection status (Off: not pressed, Solid Blue: connected, Blinking Blue: pairing).
• BT BUTTON SWITCH: Selects or exits Bluetooth input mode.
• IPOD/MP3 JACKS: Connect iPod/MP3 devices.
• HEADPHONE JACKS: Connect headphones.
• MIC INPUT JACKS 1&2: Connect karaoke microphones.
• ECHO CONTROL: Adjusts microphone echo level.
• MIC TREBLE/BASS: Adjusts microphone treble and bass.
• MIC VOLUME: Adjusts microphone volume.
• SUB. OUT VOLUME CONTROL: Controls subwoofer volume.
• MASTER VOLUME CONTROL: Adjusts the main volume.
• USB INPUT JACKS: For MP3 file playback only.

Rear Panel Function

The rear panel provides connections for antennas, audio outputs, digital audio outputs, and speaker terminals.

• 1. TUNER ANT: Connect AM and FM antennas.
• 2. R/L OUTPUT: Connect to amplifier's RCA inputs.
• 3. VIDEO OUTPUT, S-VIDEO OUTPUT, COMPONENT VIDEO OUTPUT: Select output mode via remote.
• 4/5. DIGITAL AUDIO OUTPUT: Coaxial and Optical outputs for Dolby Digital or DTS decoders.
• 6. COOLING FAN: Dissipates heat.
• 7. SUB-WOOFER OUTPUT JACKS 1&2: Connect subwoofer.
• 8. AUDIO INPUT JACKS: Connect audio outputs from MP3, AUX devices.
• 9. A SPEAKER OUTPUT TERMINALS: Connect speaker system A.
• 10. B SPEAKER OUTPUT TERMINALS: Connect speaker system B.
• 11. 110V/220V SWITCH: Select voltage input (110V or 220V).
• 12. POWER CORD: Connects to AC power outlet.

Remote Device Function

Remote Control Operation

• Operate within 6 meters (approx. 20 feet) and a 30° scope in front of the receiver.
• Ensure no large obstacles between the remote and the machine.
• Keep the remote sensor away from bright light, which can affect performance.

Remote Control Buttons

• 1. POWER STANDBY: Puts the unit in standby mode.
• 2. A/B SPEAKERS OUTPUT SELECT: Selects speaker outputs.
• 3. PAL/NTSC switch: Selects video output standard.
• 4. VIDEO button: Selects video mode.
• 5. Time select button.
• 6. Setup button: Accesses setup menus.
• 7. UP/DOWN/LEFT/RIGHT: Navigation buttons.
• 8. Play/Enter button: Starts playback or confirms selection.
• 9. Title button: Displays title menu.
• 10. AM/FM button: Selects AM/FM radio.
• 11. Stop button: Stops playback.
• 12. PLAY/PAUSE button: Controls playback.
• 13. Frequency DOWN button: Decreases radio frequency.
• 14. Frequency UP button: Increases radio frequency.
• 15. Language button: Changes audio/subtitle language.
• 16. Channel L/R button: Selects stereo or mono.
• 17. ZOOM button: Zooms the picture.
• 18. Input selection button: Selects input sources.
• 19. MENU CONTROL button: Accesses menu functions.
• 20. EJECT Open/Close button: Opens/closes disc tray.
• 21. Number button: Direct selection of tracks/stations.
• 22. Mute button: Mutes audio output.
• 23. Menu button: Opens the main menu.
• 24. PBC button: Playback control.
• 25. MEMORY button: Stores radio stations.
• 26. AUTO button: Initiates auto scan for radio stations.
• 27. PROGRAM button: Programs playback sequences.
• 28. OSD display button: Shows on-screen display information.
• 29. NEXT/CH+: Skips to next track/channel.
• 30. PREV/CH-: Skips to previous track/channel.
• 31. USB/DVD button: Switches between USB and DVD sources.
• 32. Subtitle button: Selects subtitle language.
• 33. Repeat button: Repeats tracks or titles.
• 34. A-B Repeat button: Repeats a specific section.
• 35. Volume+ button: Increases volume.
• 36. Volume- button: Decreases volume.

Safety Instructions

• Ensure all connections are proper and the main volume is set to minimum before turning the unit ON.
• When using multiple speaker pairs, ensure they have the same wattage and impedance to prevent unit damage.
• Ensure all wires are properly inserted to avoid humming sounds and unwanted noise.
• For speaker cords, strip the vinyl coating, twist the wire tip, insert into the terminal (push jack or loosen screw), and tighten the screw. Ensure wires do not stick out to prevent short circuits.
• After turning the unit ON, adjust the main volume, bass, and treble to the desired levels.

Basic Connection

Connecting to a TV with Audio/Video Cable

Connect the audio output jacks of the DVD player to the audio inputs of the amplifier. Connect the video output of the DVD player to the TV's video input. If the TV has an S-video input, use an S-video cable and do not connect the yellow video cable.

Note: Volume adjustment works only when connected to a power amplifier. If connected to a TV without speakers, volume cannot be adjusted on this device; adjust it on the TV set.

Connecting to an Audio System

Connect the amplifier's audio outputs (R/L OUTPUT) to the audio inputs of the audio system.

Connecting to an Amplifier Equipment

Connect the amplifier's various inputs (e.g., coaxial, optical, video, S-video) to the corresponding outputs of the DVD player.

Basic Playback

Preparations

• Before viewing a disc, turn on the TV and select the correct video input connected to the unit.

Basic Playback

1. Press the POWER switch on the front panel to ON. The unit turns on, and the TV screen displays the start logo. If a disc is already in the tray, playback begins automatically.
2. Press OPEN/CLOSE to open the disc tray, then place a disc on the tray. Ensure the disc is correctly guided; improper placement may damage the disc or unit. Do not place unplayable discs in the unit.
3. Press OPEN/CLOSE to close the disc tray; playback will start automatically. Some discs may require pressing the PLAY button to start.
4. Some discs may present a menu upon playback. Use the cursor buttons on the remote to select menu options and press PLAY, or use the number keys to select options directly.

Playback Controls

Pause/Step Playback

1. Press PAUSE/STEP once to pause playback (still mode). The sound will be muted.
2. Press STEP continuously to single-step forward through the video frames.
3. Press PLAY to resume normal playback.

Previous and Next

While playing, press the PREV key to play the previous chapter. Press NEXT to skip to the next chapter.

Fast Forward and Fast Reverse

1. Press FWD to fast forward through the disc; pressing it multiple times adjusts the speed.
2. Press ENTER/PLAY to resume normal playback.
3. Press REV to fast reverse through the disc; pressing it multiple times adjusts the speed.
4. Press ENTER/PLAY to resume normal playback.

Stop Playback

1. Press STOP to enter stop mode. The TV screen will show the start logo. The unit may recall the playback location for DVDs and audio CDs.
2. Press PLAY to resume playback from the stopped location or from the beginning of the disc.
3. Press STOP twice to stop playback completely.

Standby

Press the STANDBY key on the remote control to switch the player to standby mode or to power it ON.

Notes

• An "INVALID KEY" message may appear on the TV screen, indicating an operation is not permitted by the unit or the disc.
• The unit can be controlled by CPU under setting mode. Pressing any key while in screen saver mode activates the unit. If this function is unavailable, set SCREEN SAVER to OFF in SYSTEM SETUP.

Listen to Radio, Line Input Operation, Advanced Playback

MP3, AUX External Connection of Audio Signal Input

Press the INPUT key on the remote control or the unit's panel to input MP3/AUX and AM/FM external audio signals. The display shows the status.

Input Transfer to MP3, AUX

Press the INPUT key to transfer audio signals from MP3/AUX and AM/FM sources.

Listen to Radio

FM/AM

Press the INPUT key to select radio reception, then press the [FM/AM] key on the unit or remote. The unit will enter FM/AM mode, displaying the frequency and channel number.

Notes: The machine stores the radio station into the current channel number upon reception. Signal intensity affects reception quality. For poor or erratic signals, manual scan or frequency selection scan is recommended.

Manual Scan

Press the [FRE-] or [FRE+] key to manually scan for radio stations.

Auto Scan

Press the AUTO key to scan through the frequency range automatically.

Frequency Selection Scan

Press the [TIME] key on the remote control. The display shows the status. Input the desired radio station frequency (FM: 87.5-108.0MHz, AM: 530-1620KHz).

Channel Select

Press the [CH-] and [CH+] keys to select stored channels.

Radio Station Storage and Playback

Notes

Favorite radio stations can be stored in continuous channels.

Monophony/Stereo Mode Select

Press the [L/R] key on the remote control to select monophony or stereo mode.

Note: Monophony mode is advised when the radio station signal is weak.

Auto Store Radio Stations

After initiating AUTO SCAN, the machine stores received radio stations into sequential channels, automatically saving the current frequency.

Manual Store Radio Stations

Select a radio station using [FRE-] or [FRE+] keys, then press [MEMORY] to store it into the desired channel number, preferably when the signal is strong.

Advanced Playback Tips

If reception is poor or noisy, even after switching to monophony mode, adjust the antenna to achieve the best reception.

USB Reader Function

The machine plays USB drives similarly to discs, provided only one file format is present on the USB disk or card.

MP3 and WMA files have priority for playback after the machine scans the USB disk, especially if it contains multiple file types.

USB/DVD

When playing a DVD, press the [USB/DVD] key. The screen will display "READ USB" after pressing [ENTER], switching to USB status. The reverse operation switches from USB to DVD status.

USB Copy Subtitle Key Function

You can copy files to a USB drive when the machine is playing MP3, CD, or MPEG4. Press the [SUBTITLE] key on the remote control to initiate the copy process.

1. When playing an MP3 disc, press [SUBTITLE] to copy files to the USB.
2. When playing a CD disc, press [SUB TITLE] to copy songs to USB, converting them to MP3 format (select single files or all files for transfer).

Notes: This function requires sufficient USB capacity. Some models may not support this feature.

Wireless BT Connectivity

• Built-in receiver for wireless audio music streaming.
• Simple and hassle-free pairing.
• Works with smartphones, tablets, laptops, and computers.
• Bluetooth Version: 4.2
• Bluetooth Network Name: 'BT AUDIO'
• Bluetooth Password: Not Required
• Wireless Range: 40'+ ft.

Important Note on DVD Formats

The following function descriptions are for DVDs. Operation and display may differ for other disc formats.

Time

Pressing the TIME button displays messages. Use LEFT/RIGHT cursor buttons to select preferences, then press ENTER/PLAY to confirm.

OSD

Pressing this button displays "DVD n XX/XX CH XX/XX 00:00:05 (chapter elapsed)," "1/3 ENG 5.1CH 1/4 ENG • OFF", "DVD TT XX/XX CH XX/XX -00:00:00 (chapter remain)", "DVD TT XX/XX CH XX/XX -00:00:00 (title elapsed)", "DVD TT XX/XX CH XX/XX -00:00:00 (title remain)", and a sixth option to cancel the function.

Language

Press this button to change the audio mode. For example: "[1 XX 5.1CH]", where "XX" indicates the country's language (dependent on the disc).

Video

In play or stop status, press the VIDEO key to switch video output interfaces: TV-RGB, P-SCAN, S-VIDEO, INTERLACE YUV.

P/N

Press the key to switch between NTSC, PAL, and AUTO.

Zoom

Press this button to zoom into the picture. Each press changes the magnification level.

Playback Functions

Subtitle

1. Press this button to display subtitle information, e.g., "[1XX]", where "XX" indicates the country's language (dependent on the disc).

Program

This key stores your favorite picture as the starting frame. If multiple pictures are chosen, the latest one becomes the starting frame. To cancel, press [SETUP], then [ENTER] after selecting [RESTORE] key of [LOGO SELECT] under system settings.

Title/PBC

• For DVD discs: Press this button to display the title menu. Use the digits to select your preferred chapter.
• For SVCD and VCD: Follow on-screen menu instructions. Use the digits during PBC playback.

A/B Speakers Output Select

This function allows selection of speaker outputs.

Repeat

1. Press once to repeat a chapter.
2. Press twice to repeat a title.
3. Press thrice to repeat all.
4. Press four times to cancel repeat.

A-B Repeat

Press A-B to set a start point, then press again to set an end point. The selected section A-B will be repeated. A third press cancels this function.

Volume and Mute

Press the "+" button to increase volume and "-" to decrease volume. The first press of the MUTE button displays "Mute no voice"; a second press restores normal audio.

Menu

Use this to increment/decrement levels for Master Volume, Bass, Treble, Balance, and Auto Station Seek. Press the MENU key to select a function, then use the volume control buttons to adjust the selected parameter.

Special Function Playback

JPEG Disc Playback

When a JPEG disc is loaded, a navigation menu appears. Use UP/DOWN cursor buttons to select a file, then press "ENTER/PLAY" for a slideshow. Use PREV or NEXT to select pictures. Press PAUSE to freeze a picture, then ENTER/PLAY to resume the slideshow.

Zoom Function

Press the ZOOM key to activate/deactivate zoom. When active, pictures display at the last selected ratio. The ZOOM key controls zoom in/out. When ZOOM is off, pictures scale to fit the screen.

Notes: Slide-show transition and image rotation are disabled during zoom. Press ZOOM again to resume the slideshow.

MP3 Playback

Insert an MP3 disc. The player will begin playback and display a navigation menu. Use UP/DOWN cursor buttons to choose folders, then select files and press "ENTER/PLAY" to play. Use the LEFT cursor button to return to the previous menu. Use PREV or NEXT to go back pages.

MPEG-4 Disc Function Introduction

MPEG-4 is an advanced video and audio encoding standard. It offers high compression for quality video and audio. MPEG-4 technology allows encoding DVD films onto fewer discs or burning multiple films onto a single disc with good quality.

Note: MPEG-4 discs may have various formats (Xvid, AVI, RM). Discs labeled "MPEG-4" may not use MPEG technology and might not function properly.

Playback Details

MPEG-4 File Playback

1. MPEG-4 files are displayed as a list. Use cursors to select an icon and press "ENTER/PLAY" to play the movie.
2. AVI is an MPEG-4 format. Do not combine AVI with MP3/JPEG on the same disc, as the player may only recognize MP3 or JPEG. MP3 and JPEG can be included together.

Playback (Normal)

When a Kodak Picture CD is inserted, an automatic slideshow begins, displaying each picture consecutively, scaled to fit the TV screen. Transition effects can be selected using the "PROG" key. Press "PAUSE" to display an image indefinitely. Use "NEXT" or "PREV" to view other pictures. Press "ENTER/PLAY" to resume the slideshow.

Image Rotation

Four rotation modes are available: "Invert", "Mirror", "Left", and "Right". These are active only when a picture is displayed normally and cancel automatically when a new picture is displayed. Use arrow keys to select rotation modes.

Zoom

The "ZOOM" key activates/deactivates zoom. When active, pictures display at the last selected ratio. The screen indicates the current zoom ratio. The ZOOM key controls zoom in/out. When ZOOM is off, pictures scale to fit the screen.

Notes: Slide-show transition and image rotation are disabled during zoom. Press the "ZOOM" key again to resume the slideshow.

Important Note

Picture quality displayed on the screen depends heavily on the viewing device.

USB 2.0 and Compatibility

USB 2.0

USB 2.0 supports data transfers of 480 Mb/s.

Divx and Xvid Video Compatibility

1. Plays most versions of DivX and Xvid video files.
2. File Extensions: .avi and .divx are required for DivX video recognition. While .avi files may be recognized as Mp4, not all are necessarily DivX video files and may not be playable.

PC-Created Disc Compatibility

Discs created using personal computer software may not be playable due to application settings. Check with the software publisher for details. Discs recorded in packet write mode (UDF format) are not compatible. Check DVD-R/RW or CD-R/RW software disc boxes for compatibility information.

System Setup

Press the SETUP button on the remote control to access the setup menu, which includes "SYSTEM SETUP", "LANGUAGE SETUP", "AUDIO SETUP", "VIDEO SETUP", "SPEAKER SETUP", and "DIGITAL SETUP". Use UP, DOWN, LEFT, RIGHT buttons to navigate and ENTER/PLAY to select. Press LEFT to return to the previous menu. Exit setup by selecting the exit option or pressing SETUP again.

1. System Setup Page

Configure TV screen format, video type, and other DVD functions.

1.1 TV System

This player supports AUTO, NTSC, and PAL TV output systems.

Note: If your TV only supports NTSC or PAL and the wrong system is selected, the screen may flicker or display only black and white. Press the SETUP button to correct this.

How to Set the TV Type

• Switch the NTSC/PAL setting to match your TV's video signal.
• The table below shows disc compatibility with AUTO, PAL, and NTSC settings.

1.2 Auto Play

Enable or disable automatic disc playback.

1.3 HD Output

Configure HD output settings (e.g., 720P, 1080I).

1.4 Video

Set the video output (VIDEO, INTERLACE-YUV, P-SCAN, S-VIDEO).

1.5 TV Type

Selects display format and TV screen ratio for optimal viewing. Standard 4:3 format displays as 4:3. DVD titles recorded in 16:9 may appear compressed on a 4:3 screen. Special formats retain their original display.

1.6 Password

Change the password. Default is 0000. Enter a new 4-digit password.

1.7 Next Page

Select sub-items for setup.

• 1.7-1 DEFAULT: Resets all manufacturer settings.
• 1.7-2 SELECT LOGO: Resets manufacturer settings.
• 1.7-3 RESUME: Enables memory playback, recalling where playback stopped.
• 1.7-4 PREV PAGE: Navigates to the previous setup page.
• 1.7-5 EXIT SETUP: Exits the setup menu.

2. Language Setup

2.1 OSD Language

Select the language for the on-screen display and setup menus.

2.2 Audio Lang

Set the preferred audio language for DVD playback (if supported by the disc).

2.3 Subtitle Lang

Set the preferred subtitle language for DVD playback (if supported by the disc).

2.4 Menu Lang

Set the preferred menu language for DVD playback (if supported by the disc).

2.5 Exit Setup

Exits the language setup.

3. Audio Setup Page

3.1 Audio Output

Set the audio outputs (SPDIF/OFF, SPDIF/RAW, SPDIF/PCM).

3.2 Key

Use UP/DOWN arrow buttons to scroll and adjust the key.

4. Video Setup Page

4.1 Brightness

Adjusts the brightness level of the video output.

4.2 Contrast

Adjusts the contrast level of the video output.

4.3 Hue

Adjusts the hue value of the video.

4.4 Saturation

Adjusts the video saturation.

5. Speaker Setup

5.1 Speaker Setup Page

DOWNMIX MODE: Sets front speakers to LT/RT STEREO, V SURR. The first three settings (LT/RT, STEREO, V SURR) downmix the sound signal for 2-speakers, enabling a surround sound effect with only two speakers. Additional speaker setups are disabled when DOWNMIX MODE is set to these options.

6. Digital Setup Page

6.1 OPMODE

Set the type of output and adjust audio frequency.

6.2 Dynamic Range

When LINE OUT is selected, adjust the line out ratio. Setting to FULL minimizes audio signal peak value; OFF maximizes it.

6.3 Dual Mono

If your amplifier/decoder supports Dolby Digital output, select stereo, left mono, right mono, or mixed mono mode.

7. Source

The system automatically reads USB if no playable disc is loaded. Use the Source menu to select disc or USB directory.

Troubleshooting

DVD Special Function: Setting the TV Screen Size

Multi-aspect ratio suits different TV screen sizes.

Functions Supported by DVD Discs

Many functions are available on DVD discs, varying by player and manufacturer.

• Regional code and signal system
• Dolby digital surround sound
• Number of languages
• Subtitle languages
• Picture proportion modes
• Parental Control
• Angles for viewing

Product Features and Specifications

Features

• Audio / Video Home Theater Pre-Amplifier
• 4-Ch. Pro Audio Receiver System
• Connects to TVs, Soundbars, Speaker Systems
• Built-in Bluetooth for Wireless Music Streaming
• Front Loading CD/DVD Player
• Powers up to (4) Loud Speakers
• Front Panel Control Center with Digital LCD Display
• AM/FM Stereo Radio
• USB Flash Drive Reader
• MP3 Digital Audio File Compatibility
• (4) Pair Speaker Terminal Binding Posts
• (2) Pair RCA (L/R) Audio Inputs
• Aux (3.5mm) Input Jack
• (2) 1/4" Microphone Inputs
• 1/4" Headphone Jack
• Subwoofer RCA (L/R) Output
• Optical (Digital) Audio Output
• Video Outputs: S-Video, RCA YPbPr (Component Video)
• Output dB (Decibel) Level LED Display
• Mic Echo, Treble, Bass, Volume, Subwoofer Controls
• Sleek Brushed Aluminum and Metal Chassis Housing
• Built-in Ventilation Cooling Fan
• Universal Rack Mountable

Bluetooth Connectivity

• Works with all favorite Bluetooth Devices (iPhone, Android Smartphones, iPad, Tablets, etc.).
• Bluetooth Network Name: 'BT AUDIO'
• Bluetooth Network Password: Not Required
• Bluetooth Version: 4.2
• Bluetooth Wireless Range: 40'+ ft.

What's in the Box

• Preamplifier Receiver
• Remote Control
• Detachable Rack Mount Brackets
• RCA Connection Cables
• AM/FM Antennas
• Power Cable

Technical Specs

• PD1000BT Power Output: 1000 Watt MAX
• PD3000BT Power Output: 3000 Watt MAX
• Amplifier Receiver Type: 4-Channel
• Impedance: 8 Ohm
• Aspect Ratio: 4:3/16:9
• Video System: PAL/NTSC
• Audio S/N Ratio: >90dB
• Frequency Range: +/-14 dB
• Quartz Synthesized Radio Tuner
• Radio Presets: 50 Station Memory
• CD/DVD Disc Compatibility: DVD/CD/VCD/CD-R/CD-RW/MP4/MP3/WMA/CDG
• Power Supply: 120/240V, Switchable
• Dimensions (L x W x H): 18.89" x 12.79" x 5.19" -inches

Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com

WARNING: This product can expose you to a chemical or group of chemicals, which may include "Nickel Carbonate," which is known in the state of California to cause cancer, birth defects, or other reproductive harm. For more info, go to https://www.p65warnings.ca.gov/.