Bryton Rider 460

Preliminary Review

The Bryton 400 is a 2020 model featuring a wide range of sensor compatibility and GPS capabilities.

Warranty and Safety Information

For detailed warranty and safety information, please refer to the full documentation available at Bryton Sport.

Important Safety Notes:

• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children.
• Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death. Call a local poison control center for treatment information.
• Battery type: CR2032; Battery voltage: 3VDC.
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above specified temperature rating, or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.
• Ensure batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period.
• Always completely secure the battery compartment. If it does not close securely, stop using the product, remove the batteries, and keep them away from children.

Sensors Pairing _ Cadence Sensor

Pairing Bryton Smart Sensors with Your ANT+/BLE Devices

After installing Bryton Smart Sensors, rotate the crank and wheel a few times to wake them up. Sensors can only be paired when awake.

Note:

• Pairing steps may differ for each Bryton device. Consult your device's user manual.
• Keep away from other ANT+ or BLE sensors during pairing.

Connecting to Your ANT+/BLE Devices

After pairing, your Bryton devices will automatically connect to Bryton Smart Sensors each time they are awake.

Rider 460 Specifications

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

FCC Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Australian Consumer Law

Our goods come with guarantees that cannot be excluded under Australian consumer law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Industry Canada Compliance

This device complies with Industry Canada license-exempt RSS-247 and ICES-003 standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device.

IC RF Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0.5cm between the radiator & your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

CE Marking Warning

This is a Class B product, in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

RF Exposure Information

This device meets the EU requirements and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. To comply with the RF exposure requirements, this equipment must be operated in a minimum of 0.5cm separation distance to the user. Bryton Inc. declares that the radio equipment type Bryton product is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://global.brytonsport.com/pages/support_documents

Mount Rider 460 to the Bike

Step 1: Attach the mount to your handlebars using the provided strap and screws.

Step 2: Slide the Rider 460 onto the mount until it clicks into place.

Step 3: Ensure the device is securely attached before riding.

Safety Lanyard

For added security, attach the safety lanyard to your device and handlebars.

Support & Download

For more information and support, please visit: https://www.brytonsport.com > Support&Download