User Guide for imotion models including: MC432, SPYMC432, MC432, MC432L, MC432 Mobile Computer, Mobile Computer, Computer
iWaylink Inc. MC432 Mobile Computer SPYMC432 SPYMC432 mc432
File Info : application/pdf, 3 Pages, 1.64MB
DocumentDocumentMobile Computer
MC432/MC432L
Quick Start Guide
General Safety Rules
Please read this Guide carefully before you start using this device. Use only the MC432/MC432L components and accessories supplied by
the manufacturer. Do not attempt to disassemble the MC432/MC432L, as it does not contain
parts that can be repaired by the user. Any tampering will void the warranty. Discard replaced battery packs properly according to local laws. At the end of this device's product life, dispose of properly according to
local laws. Do not submerge the MC432 in any type of liquid. Charging Temperature0 to 45
Package Contents
MC432/MC432L Mobile Computer Battery Pack (with Rechargeable Battery) Quick Start Guide USB Charge/Communication Cable Quick Charge Compliant Power Adapter
After unpacking, please inspect package contents. If any item is damaged or missing, please contact your customer support representative immediately.
Features
Front View
Speaker Scan LED Charging LED
Touch Screen
Scan Button Keypad Mic
Back View Side View
Laser Warning Label
Speaker
Camera
Flash LED
Hand Strap
Attachments
Battery Cover Lock
Switch
Battery Pins
Micro SD Card Slot SIM Card Slot(For
MC432L)
Volume Up/Down
Headphone Jack
Power Button
Scan Buttons
Top View
Scan Window
Bottom View
Charging Pin / USB C
Connecter
Charging Instructions
The MC432/MC432L battery pack is not initially fully charged. After installing the battery pack, please charge it via the USB cable or the charging cradle. As default, the battery pack is disconnected at the factory to avoid damage caused by excessive draining. Replace the battery pack annually to ensure maximum performance. Avoid storing batteries for long periods of time in fully charged or very low battery level status. To maintain a moderate charge and maximize battery life, charge spare battery packs every two to three months.
Installing the Battery Pack 1. Press and push the Battery Lock Switch to Open and remove the Battery
Cover. 2. Align the Battery Pack and the device connectors and slide it into the Battery
Slot. 3. Slide the Battery Cover into place. 4. Press and push the Battery Lock Switch to Lock to secure the battery.
Battery Cover Battery Pack Battery Slot
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES PROPERLY ACCORDING TO LOCAL LAWS.
Charging via USB Cable Use the provided USB charge/communication cable together with the Quick Charge compliant power adapter to charge the MC432MC432L from a power outlet.
Charging via Charging Cradle Place the MC432/MC432L in the charging cradle. Attach the power adapter to the cradle, and then plug the power adapter into a power outlet.
Charging Time Charging time required will vary depending on the actual application of the MC432/MC432L and the condition of the battery pack. This device is shipped with a lithium-ion battery that is not fully charged. Please charge this device fully before first time use. Use under environment temperatures of 0°C~45°C.
Rated Voltage InputAC 100-240V, 50/60Hz, 0.5A Output (1) DC 5V,3A/9V,2A (2) DC 5V,2.5A/9V,2A(For USA)
Micro SD / SIM(For MC432L) Card Installation
1. Turn off the MC432/MC432L. 2. Open the Battery Cover and remove the Battery Pack. 3. Locate the SIM or Micro SD Card Slot inside the Battery Slot. 4. Insert the SIM Card or Micro SD Card into the appropriate slot. 5. Gently press and slide the card up until it clicks into place. 6. Reinstall the Battery Pack and Battery Cover.
Scanning a Barcode Label
1. Point the scan window at the barcode you wish to scan. 2. Tap Scan on the Scan app screen or press a scan button on the
MC432/MC432L. 3. The imager projects a laser aiming pattern to position the barcode in the
imager's field of view. Center the laser dot and cross-hair aiming pattern on the barcode. 4. Release the scan button to capture and decode the image.
Laser Safety Do not stare into the beam of the laser light from this device. The MC432/MC432L uses an imager Aiming System with a laser light that is visible to the human eye and is emitted from the scan window at the top of the device.
Laser Light - Do not stare into this Beam Class 2 Laser
Product. The maximum output radiation is 1 mW
compliant with EN 60825-1 (2007)
Important Notices and Precautions The manufacturer has made safety the first priority during the design stage. To avoid potential mishaps, please observe the following notices and precautions:
Do not stock this device under high temperature conditions that may cause the battery to overheat.
Do not charge longer than required. When the charging light is red, stop charging immediately.
Charge this device in a place without any water-spray or moisture.
Use a dry cloth to wipe any dust off of the AC adapter plug to avoid potential fire.
Do not drop this device on hard surfaces. Do not place heavy objects on this device to avoid cracking
the enclosure. Do not unplug the AC adapter with wet hands to avoid
electric shock. Do not use the AC adapter of the MC432/MC432L with any
other devices. Do not place the device in liquids to prevent short-circuits or
fire. Do not place this device near an open fire. If the power or USB cable is seriously twisted or broken,
stop using immediately to prevent electric shock, short-circuit, or fire. Stop using immediately if there is any unusual smell or overheating during charging or operation. Stop using immediately when there is liquid or dew on the device. Do not use the AC adapter outdoors. Please do not wrap the AC adapter with cloth or other objects that could block heat dissipation and cause electric shock or fire. When not charging, remove the AC adapter plug from the wall AC outlet socket to avoid a fire hazard.
Important Notices When Using Before replacing the battery pack due to failure, shortened life, or unusual
behavior, please confirm that the device has been used correctly, with no user operation issues involved. The manufacturer is not responsible for possible missing data or interference encountered during wireless transmissions. Do not use alcohol, benzene, organic solvents, cleaning liquid, or steel wool on the surface of this device. Do not scratch or mar the surface of the Scan Window in any way to avoid barcode scanning problems.
Bluetooth This device is designed based on Bluetooth standard specifications.
However, compatibility problems may still occur with other Bluetooth devices. Before using this device, please make sure there is no other wireless device operating within a short distance of the same application area that may cause wireless signal interference.
Signal Interference from TV or Radio Sometimes transmitting or receiving data may fail due to signal interference
from nearby TV or radio devices.
Audio Safety
To prevent possible hearing damage, do not listen at high volume levels for long periods of time.
European Union Regulatory Notes 1. Requirements for AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV
/LI/LT/LU/HU /MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/UK/HR.5150MHz~5350MHz is for indoor use only. 2. iMotion declares that the radio equipment type for the MC432/MC432L is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.iwaypro.com
Hot Part Warning
SAR Compliance
SAR Information (European Union): Head: 0.297 W/kg@ 10g (CE) Body: 1.29 W/kg@ 10g (CE)
This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range.
Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements in Europe, a minimum separation distance of 0.5cm must be maintained between the use's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided.
Power and Frequency Ranges
Radio Type Bluetooth
WLAN
Description Bluetooth BR+EDR Bluetooth 4.0-LE 2.4GHz
5GHz
GSM 850
GSM(For MC432L)
GSM 900 GSM 1800
GSM 1900
WCDMA Band I
WCDMA Band II
WCDMA(Fo r MC432L)
WCDMA Band IV
WCDMA Band V
WCDMA Band VIII
LTE Band 1
LTE Band 2
LTE(For MC432L)
LTE Band 3 LTE Band 4 LTE Band 5
LTE Band 7
LTE Band 8
Frequency
2400~2483.5 MHz 2400~2483.5 MHz 2400~2483.5 MHz 5150~5350 MHz 5475~5850 MHz 824~849 MHz 880~915 MHz 1710~1785 MHz 1850~1910 MHz 1920~1980 MHz 1850~1910 MHz 1710~1755 MHz 824~849 MHz 880~915 MHz 1920~1980 MHz 1850~1910 MHz 1710~1785 MHz 1710~1755 MHz 824~849 MHz 2500~2570 MHz 880~915 MHz
Maximum Output
10dBm 0dBm 18dBm 16dBm 16dBm 33dBm 33dBm 30dBm 30dBm 24dBm 24dBm 24dBm 24dBm 24dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm
LTE(For MC432L)
Other
LTE Band 20 LTE Band 28 LTE Band 38 LTE Band 39 LTE Band 40 LTE Band 41 NFC GPS
832~862 MHz 703~748 MHz 2570~2620 MHz 1880~1920 MHz 2300~2400 MHz 2496~2690 MHz 13.56 MHz 1575.42 MHz
23dBm 23dBm 23dBm 23dBm 23dBm 23dBm
FCC Warning Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
Max SAR0.991(Body)
The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product is kept as far as possible from the user's body or if the device is set to a lower output power if such function is available.
Taiwan NCC Warning Statement
:
3010 221 SAR2.0W/Kg0.297W/Kg NCCGSM, WCDMA B1/8, LTE 1/3/7/8/28/38/41, WLAN, BT FCCSupportGSM, WCDMA B2/5, LTE 2/4/5/7/12/17/38/41, WLAN, BT Operation Temp.'-20°C. to 50°C. / Rating:
/Input : AC 100-240V, 50/60Hz, 0.5A /Output : (1) DC5V,3A / 9V, 2A (2) DC 5V,2.5A / 9V, 2A (For USA)
:
iWaylink Inc.
6F., No.288, Sec. 6, Civic Blvd.,Xinyi Dist., Taipei City, Taiwan https://www.iwaypro.com/
MC432/MC432L
operation.
The temperature of battery surface may increase during
MC432/MC432L MC432/MC432L
MC432/MC432L : 045
MC432/MC432L USB/
LED
Micro SD SIM (For
MC432L)
LED LED
/
/ USB
MC432/MC432USB 1. 2. 3. 4.
USB USB/MC432
MC432/MC432L
MC432/MC432L 045
AC 100-240V, 50/60Hz, 0.5A (1) DC 5V,3A/9V,2A (2) DC 5V,2.5A/9V,2A(For USA)
Micro SD / SIM(For MC432L)
1. MC432/MC432L 2. 3. SIMMicro SD 4. SIMMicro SD 5. 6.
1. 2. MC432/MC432L
3.
4.
MC432/MC432L
- 2 1 mW EN 60825-12007
AC AC MC432/MC432L AC
USB
AC
AC AC AC
1. AT / BE / BG / CZ / DK / EE / FR / DE / IS / IE / IT / EL / ES / CY / LV / LI /
LT / LU / HU / MT / NL / NO / PL / PT / RO / SI / SK / TR / FI / SE / CH / UK / HR 5150MHz~5350MHz 2. iMotion MC432 2014/53
www.iwaypro.com
SAR SAR
0.297 W / kg @ 10gCE 1.29 W / kg @ 10gCE 5150 5350 MHz
0.5
BR + EDR 4.0-LE 2.4GHz
5GHz
GSM(For MC432L) WCDMA(For MC432L)
LTE(For MC432L)
Other
GSM 850 GSM 900 GSM 1800 GSM 1900 WCDMA I WCDMA II WCDMA IV WCDMA V WCDMA VIII LTE 1 LTE 2 LTE 3 LTE 4 LTE 5 LTE 7 LTE 8 LTE 20 LTE 28 LTE 38 LTE 39 LTE 40 LTE 41 NFC GPS
2400~2483.5 MHz 2400~2483.5 MHz 2400~2483.5 MHz 5150~5350 MHz 5475~5850 MHz 824~849 MHz 880~915 MHz 1710~1785 MHz 1850~1910 MHz 1920~1980 MHz 1850~1910 MHz 1710~1755 MHz 824~849 MHz 880~915 MHz 1920~1980 MHz 1850~1910 MHz 1710~1785 MHz 1710~1755 MHz 824~849 MHz 2500~2570 MHz 880~915 MHz 832~862 MHz 703~748 MHz 2570~2620 MHz 1880~1920 MHz 2300~2400 MHz 2496~2690 MHz 13.56 MHz 1575.42 MHz
10dBm 0dBm 18dBm 16dBm 16dBm 33dBm 33dBm 30dBm 30dBm 24dBm 24dBm 24dBm 24dBm 24dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm 23dBm
FCC
FCC151 2
FCC15B
/
FCC
FCC15.40715E FCC
SAR0.991W/Kg ()
Taiwan NCC Warning Statement
:
3010 221 SAR2.0W/Kg0.297W/Kg NCCGSM, WCDMA B1/8, LTE 1/3/7/8/28/38/41, WLAN, BT FCCSupportGSM, WCDMA B2/5, LTE 2/4/5/7/12/17/38/41, WLAN, BT Operation Temp.'-20°C. to 50°C. / Rating:
/Input : AC 100-240V, 50/60Hz, 0.5A /Output : (1) DC5V,3A / 9V, 2A (2) DC 5V,2.5A / 9V, 2A (For USA)
:
288 6 https://www.iwaypro.com
Microsoft Word 2013 Microsoft Word 2013