Gallagher T15 Reader
Installation Note
Product Variants
The Gallagher T15 Reader is available in ten variants, supporting various technologies:
| Reader Variant | Product Codes | Card Technologies Supported | NFC Access for Android Supported From | Bluetooth® Access Supported From | HBUS Comms Supported From | Cardax IV Comms Supported From |
|---|---|---|---|---|---|---|
| T15 MIFARE Reader | C300470, C300471 | ISO 14443A MIFARE® DESFire® EV1/EV2*, MIFARE Plus®, and MIFARE Classic® cards | vEL7.80 HBUS only | None | vEL7.00 | vEL1.02 |
| T15 Multi Tech Reader | C300480, C300481 | ISO 14443A MIFARE DESFire EV1/EV2*, MIFARE Plus, MIFARE Classic, and 125 KHz cards | vEL7.80 HBUS only | vEL7.60 HBUS only | vEL7.00 | vEL1.02** |
| T15 PIV Reader | C305470, C305471 | ISO 14443A PIV, PIV-I, CAC, TWIC, MIFARE DESFire EV1/EV2*, MIFARE Plus, and MIFARE Classic cards | vEL7.80 HBUS only | None | vEL7.10 | None |
| T15 PIV Reader - Multi Tech | C305480, C305481 | ISO 14443A PIV, PIV-I, CAC, TWIC, MIFARE DESFire EV1/EV2*, MIFARE Plus, MIFARE Classic, and 125 KHz cards | vEL7.80 HBUS only | None | vEL7.10 | None |
* MIFARE DESFire EV2 is supported from vEL7.70.
** Gallagher recommends against using dual technology 125/MIFARE cards with Multi Tech Readers for sites running pre-Command Centre v7.00 software. From Command Centre v7.00, a site may specify which technology a Multi Tech Reader should read off a dual technology card.
Introduction
The Gallagher T15 Reader is a smart card and Bluetooth® low energy technology reader. It can be installed as either an entry reader or exit reader. The reader sends information to the Gallagher Controller and acts upon information sent from the Gallagher Controller. The reader itself does not make any access decisions.
Before You Begin
Shipment Contents
- 1 x Gallagher T15 Reader facia assembly
- 1 x Gallagher T15 Reader bezel
- 1 x M3 Torx Post Security screw
- 2 x 25 mm No.6 self tapping, pan head, Phillips drive fixing screws
- 2 x 40 mm No.6 self tapping, pan head, Phillips drive fixing screws
Power Supply
The Gallagher T15 Reader operates on a supply voltage of 13.6 Vdc. A linear or good quality switched-mode power supply is recommended. Low quality or noisy power supplies may affect performance.
Cabling
A minimum cable size of 4 core 24 AWG (0.2 mm²) stranded security cable is required for data and power transmission. Consideration must be given to power supply voltage drop and data requirements when using a single cable.
HBUS Cabling Topology
The HBUS communications protocol is based on the RS485 standard, supporting distances up to 500 m (1640 ft). Cabling should follow a "daisy chain" topology; "T" or "Star" topologies are not permitted between HBUS devices. For "Star" or "Home-Run" wiring, HBUS 4H/8H Modules and HBUS Door Modules can be used. End devices require 120 ohms termination resistance. For Gallagher Controller 6000, connect the supplied on-board termination jumpers. For readers, connect the orange (termination) wire to the green (HBUS A) wire. HBUS Modules have integrated termination.
[Diagrammatic representation of HBUS topology: Shows valid daisy chain connections between HBUS devices and a Controller 6000, with notes indicating that "T" or "Star" circuits are not permitted between HBUS devices. Includes examples of termination jumper usage.]
Cable Distance
| Cable Type | Cable Format | HBUS single reader (data only) | Cardax IV single reader (data only) | HBUS/Cardax IV single reader (power and data) |
|---|---|---|---|---|
| CAT 5e or better** | 4 twisted pair each 2 x 0.2 mm² (24 AWG) | 500 m (1640 ft) | 200 m (650 ft) | 100 m (330 ft) |
| BELDEN 9842** (shielded) | 2 twisted pair each 2 x 0.2 mm² (24 AWG) | 500 m (1640 ft) | 200 m (650 ft) | 100 m (330 ft) |
| SEC472 | 4 x 0.2 mm² Not twisted pairs (24 AWG) | 400 m (1310 ft) | 200 m (650 ft) | 100 m (330 ft) |
| SEC4142 | 4 x 0.4 mm² Not twisted pairs (21 AWG) | 400 m (1310 ft) | 200 m (650 ft) | 150 m (500 ft) |
| C303900/ C303901 Gallagher HBUS Cable | 2 Twisted pair each 2 x 0.4 mm² (21 AWG, Data) and 2 x 0.75 mm² Not Twisted Pair (~18 AWG, Power) | 500 m (1640 ft) | 200 m (650 ft) | 450 m (1490 ft) |
Notes:
- Shielded cable may reduce obtainable length; ground at the Controller end only.
- Other cable types may reduce operating distances and performance.
- HBUS supports up to 20 readers per cable. Each reader requires 13.6 Vdc. Cable length and reader count impact voltage at each reader.
Distance Between Readers
Proximity readers must be separated by at least 200 mm (8 inches) in all directions. For internal walls, ensure readers on opposite sides are at least 200 mm (8 inches) apart.
[Diagram illustrating minimum reader separation: Shows two readers 200mm apart, and a cross-section of a wall with readers on either side also separated by 200mm.]
Installation
ATTENTION: This equipment contains components sensitive to electrostatic discharge. Ensure you and the equipment are earthed before servicing.
The Gallagher T15 Reader mounts on any solid flat surface. Installation on metal surfaces, especially those with large surface areas, can reduce read range.
Note: Consider the installation environment for Bluetooth® enabled readers, as read range may be affected.
The recommended mounting height is 1.1 m (3.6 ft) from the floor to the reader's center. Local regulations may require variations.
- Use the reader bezel as a guide to drill three holes: a 13 mm (1/2 inch) diameter center hole for the cable exit, and two fixing holes.
- Run the building cable through the center hole and the reader bezel.
- Secure the bezel to the mounting surface using the provided fixing screws. Ensure the bezel is flush and tight. Gallagher recommends using the outer screw locations.
Note: Use the provided screws. Alternative screws must have heads no larger or deeper than the provided ones.
Note: The center hole must allow the cable to pass freely for the reader facia to clip into the bezel.
[Diagram illustrating installation steps: Shows a bezel, building cable, and screw placement for mounting. Labels include "No. 6 pan head screw", "Building cable", and "Bezel".]
- Connect the reader tail to the building cable. Wire connections depend on whether it's an HBUS Reader or a Cardax IV Reader, as shown in the diagrams below.
Note: PIV and Bluetooth® readers must connect as HBUS Readers. PIV readers connect only to the Gallagher Controller 6000 High Spec PIV (C305101).
HBUS Reader Connection
| HBUS Reader | Color |
|---|---|
| Positive | Red |
| Negative | Black |
| HBUS Termination | Orange |
| HBUS A | Green |
| HBUS B | Brown |
| CDXIV TX | White |
| CDXIV RX | Blue |
Note: To terminate an HBUS Reader, connect the Orange (HBUS Termination) wire to the Green (HBUS A) wire.
Cardax IV Reader Connection
| Cardax IV Reader | Color |
|---|---|
| Positive | Red |
| Negative | Black |
| HBUS Termination | Orange |
| HBUS A | Green |
| HBUS B | Brown |
| CDXIV TX | White |
| CDXIV RX | Blue |
An HBUS Reader connects to a Gallagher Controller 6000, Gallagher 4H/8H Module, or Gallagher HBUS Door Module. A Cardax IV Reader connects to a Gallagher Controller 6000, Gallagher 4R/8R Module, or Gallagher GBUS Universal Reader Interface.
- Fit the facia assembly into the bezel by clipping the top lip, then pressing the bottom down.
- Insert the M3 Torx Post Security screw through the bottom of the bezel to secure the facia assembly. Use a T10 Torx Post Security screwdriver. Tighten lightly.
[Diagram showing reader tail, building cable, and connection point, with a screw securing the facia to the bezel.]
- Removal of the facia assembly is the reverse of these steps.
Hint: After removing the security screw, press the top of the facia; the bottom will exit the bezel.
- Configure the reader in Command Centre. Refer to the Command Centre Configuration Client Online Help for "Configuring HBUS Devices" (for HBUS Readers) or "Creating Readers" (for Cardax IV Readers).
LED Indications
HBUS Indication
| LED (squiggle) | HBUS Indication |
|---|---|
| 3 Flash (Amber) | No communications with the Controller. |
| 2 Flash (Amber) | Communications with the Controller, but reader is not configured. |
| 1 Flash (Amber) | Configured to a Controller, but reader is not assigned to a door or elevator car. |
| On (Green or Red) | Fully configured and functioning normally. Green = Access mode is Free, Red = Access mode is Secure |
| Flashes Green | Access has been granted. |
| Flashes Red | Access has been denied. |
| Flashes (Blue) | Reading and validating a PIV card. Reading a Gallagher mobile credential. |
Cardax IV Indication
| LED (squiggle) | Cardax IV Indication |
|---|---|
| 3 Flash (Amber) | No communications with the Controller. |
| On (Green or Red) | Fully configured and functioning normally. Green = Access mode is Free, Red = Access mode is Secure |
| Flashes Green | Access has been granted. |
| Flashes Red | Access has been denied. |
Accessories
| Accessory | Product Code |
|---|---|
| T15 Bezel, Black, Pk 10 | C300296 |
| T15 Bezel, White, Pk 10 | C300297 |
| T15 Bezel, Silver, Pk 10 | C300298 |
| T15 Bezel, Gold, Pk 10 | C300299 |
| T15 Dress Plate, Black, Pk 10 | C300324 |
Technical Specifications
| Routine Maintenance: | Not applicable for this reader | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Cleaning: | This reader should only be cleaned with a clean, lint free, damp cloth. | |||||||||||||
| Voltage: | 13.6 Vdc | |||||||||||||
| Current³: |
| |||||||||||||
| Temperature Range: | -35 °C to +70 °C⁴ Note: Direct sunlight may increase the internal reader temperature above the ambient temperature level. | |||||||||||||
| Humidity: | 0 - 95% non-condensing⁵ | |||||||||||||
| Environmental Protection: | IP68⁶ | |||||||||||||
| Impact Rating: | IK07⁶ | |||||||||||||
| Unit Dimensions: | Height 139 mm (5.47 inches) Width 44 mm (1.73 inches) Depth 23 mm (0.9 inches) | |||||||||||||
| Maximum Number of Readers on One HBUS Cable: | 20 |
Footnotes:
- The reader is idle.
- Maximum reader current during credential read.
- Current values are based on default Command Centre configuration. Changes may vary values. UL verified currents are in "3E2793 Gallagher Command Centre UL Configuration Requirements".
- Gallagher T Series readers are UL temperature tested for 0°C - 49°C (indoor) and -35°C - +66°C (outdoor).
- Gallagher T Series readers are UL humidity tested to 85% and independently verified to 95%.
- Environmental protection and impact ratings are independently verified.
Approvals and Compliance Standards
[WEEE Symbol: A crossed-out wheeled bin indicates that this product must not be disposed of with household waste. Users are responsible for handing over waste equipment to designated collection points for recycling, helping to conserve resources and protect human health and the environment.]
RoHS Compliant: This product complies with environmental regulations for the Restriction of Hazardous Substances (RoHS) in electrical and electronic equipment, prohibiting certain hazardous substances in the EU.
FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) no harmful interference, and (2) acceptance of any received interference. Modifications not expressly approved by Gallagher Limited may void user authority. This equipment has been tested and found to comply with Class B digital device limits, providing reasonable protection against harmful interference in residential installations. If interference occurs, users are encouraged to try measures like reorienting the antenna, increasing separation, connecting to a different circuit, or consulting a dealer/technician.
Industry Canada: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) no interference, and (2) acceptance of any interference. The French statement is: "Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement."
UL Installations: Refer to document "3E2793 Gallagher Command Centre UL Configuration Requirements" for UL system configuration. Installers must follow these instructions for UL compliance.
AS/NZS IEC 60839.11.1:2019 Grade 4, Class II
BIS: The C300480 variant of the T15 Readers is the only variant that complies with BIS.
[Bluetooth® Logo: Indicates Bluetooth® wireless technology compatibility.]
Mounting Dimensions
[Diagram showing mounting dimensions for the T15 Reader. Key dimensions provided are: Height 139 mm (5.47"), Width 44 mm (1.73"), Depth 23 mm (0.9"). A 13 mm (1/2") diameter hole is indicated for the cable. Other dimensions include 67 mm (2.64") and 16 mm (0.63"). The diagram is noted as not to scale.]
