Arti-Life Indoor & Outdoor Handrail

Arti-Life Handrails for Outdoor Steps

Experience modern and beautiful design with Arti-Life handrails, suitable for both indoor and outdoor use.

• ? Well Designed & Sturdy
• ? More Valuable
• ? Easy to Install
• ⬆️ Continuous upgrade

Key Upgrades and Features

Visual comparison highlighting the durability and material advantages of Arti-Life's metal end caps over plastic alternatives.

About the Solar Light

The solar motion sensor light automatically detects ambient brightness.

• It enters charging mode during the day, converting light into electricity stored in the built-in battery.
• At night, it automatically enters motion detection mode to illuminate when motion is detected.

Operation Guide:

Short press the middle button (White) to activate the product and press again to choose a lighting mode.

NOTICE: If you want to test whether the product can function well in daytime, you could cover the whole Solar panel with your hands. ?Illustration showing a hand covering the solar panel to test functionality.

Three Models:

• Model 1: Press once.
  • No Motion: Light Off
  • Motion Detected: High Light
• Model 2: Press again.
  • No Motion: Dim Light
  • Motion Detected: High Light
• Model 3: Press again.
  • Always on / Medium Light

Visuals illustrating the three lighting modes based on motion detection.

Charging and Installation Notice:

Before the first use, the solar light needs to be placed in the sun for 2-3 days to charge before installation. ☀️

Make sure there is sunlight shining on the front of the light's solar panel before installation. ☀️

Diagrams showing the solar light charging in sunlight and sunlight hitting the mounted solar panel.

Package List

Suitable for 2/3/4 steps use.

An overview image displaying all the components and hardware included in the package.

Installation Instructions

Step 1: Install Cover-up

Put on cover-up A4 from the top of the column A2.

Illustration showing the cover-up (A4) being placed onto the top of the column (A2).

Notice: Please place the cover-up in the correct direction.

Step 2: Install Connector

Install the A5 connector of the handrail pipe with B4 screws. The left and right directions of the two connectors are the same.

Install the A6 connector of the column with B4 screws. The up and down directions of the two connectors are opposite.

Diagrams illustrating the attachment of connectors (A5, A6) to the handrail pipe (A1) and columns (A2) using screws (B4).

There are two ways to tighten B4 into the connector:

1. Tighten B4 by hand with an Allen wrench. ?
2. Tighten B4 by electric drill. (Drill not included in package) ?

Visuals showing tightening methods with an Allen wrench and an electric drill.

Step 3: Make Adjustments

1. Insert the two sides of the A3 (connecting pipe) into the A6 (column connectors) respectively.
2. Insert the A2 (column) into the A5 (handrail pipe connectors).
3. Place the assembled parts onto the steps and make necessary adjustments.

Illustrations showing the assembly sequence: connecting pipe to column connectors, columns to handrail connectors, and final placement with adjustments.

About the Screws & Nuts

After adjusting the angle, align with pre-drilled hole position and install the B3 screw to secure it using C1 and C2 tools. (The angle cannot be adjusted after tightening the B3 screw).

Schematic diagram of the final installation showing screw placement and tools.

What we consider:

• To avoid the bolts in the connector of the handrail pipe hurting your hands.
• For aesthetic considerations, we provide not too long bolts, which are just enough when you tighten them.

We will optimize this installation method in the next version.

Installation Tip: Twist the nut by your hand first. After adjusting the angle, use a Phillips screwdriver (C2) and a double-ended wrench (C1) to tighten them. ✔️

Step 4: Drill Holes and Install Screws

Fix the A2 (column) on the ground. Select suitable accessories and punch holes according to the ground conditions.

Cement/Brick Floors: Drill holes with the provided drill B5. Drill a hole of at least 35 inches deep (90 cm), and fix the column with expansion screws B1. ?

Wooden Floor: Fix the column with self-tapping screws B2. ?

Visuals demonstrating drilling and screw installation for different floor types. Includes indicators for hole depth: 'Not deep enough' (❌), 'Perfect depth' (✔️), 'Too deep' (❌).

Diagrams showing self-tapping screws for wooden floors and expansion screws for concrete/brick floors.

Notice: Tighten all parts of the connector to ensure stability, and put down the cover-up to protect the bottom of the column finally.

Step 5: Install Solar Light

Step 1: Secure the solar light and mounting bracket using the provided screws and nuts. Tighten them firmly through the holes indicated in the diagram to ensure a secure fit.

Step 2: Position the mounting bracket on the A3 (connecting pipe). Adjust the angle of the bracket to align the bottom of the solar light parallel to the ground and vertically centered.

Step 3: Use the two screws to firmly fix the mounting bracket onto the A3 connecting pipe. Remember, you can also adjust the angle during the fixing process. Once the desired angle is achieved, tighten the screws securely.

Illustrations detailing the solar light installation process: securing the bracket, positioning and adjusting it on the connecting pipe, and final fixing. Mentions using double-sided tape between the light and hanging piece.

Make sure there is sunlight shining on the front of the lights. ☀️

Enjoy Your Life, Starts Here.

Arti-Life Handrails are designed to enhance the safety and aesthetics of your home.

Images showcasing the handrail installed on a porch, in a yard, and indoors.

Applications:

• Porch
• Yard
• Indoor