Instruction Manual for Ronix models including: 5701 Scroll Saw, 5701, Scroll Saw, Saw
Ronix 5701, 120W Scroll Saw |
SCROLL SAW 5701 TECHNICAL SPECIFICATION Model Power Voltage Frequency Motor Type Speed Range Base Plate Size Tilt Range Blade Length Blade Material Cutting Depth Cutting Size Total Length Table Material Weight (N.W) Includes 5701 120W 220-240V 50-60Hz Magnetic Steel Motor 400RPM-1600RPM 400×245×95mm 0° To 45° 125mm 60Si2Mn 0°: 50mm 45°: 23mm 406mm 415mm (work table) Steel 11Kg saw balde1pc assembled with machine, soft shaft 1set, wrench 1pc 1 USER MANUAL PART LIST 5 6 4 7 8 10 12 3 9 11 1- Switch 2- Speed Variator 3- LED Light 4- Blower System 5- Safety Cover 6- Blade Attachment System 7- Table 8- Tilting Table 9- Blade Tension 10- Dust Outlet Pipe 11- Soft Shaft GENERAL POWER TOOL SAFETY WARNINGS WARNING! - Read all safety warnings and all instructions. Failure to follow the 2 SCROLL SAW warnings and instructions may result in electric shock, fire, and or serious injury. - Save all warnings and instructions for future reference. - The term "power tool" in the warnings refers to your mains-operated (corded) power tools or battery-operated (cordless) power tools. WORK AREA SAFETY - Don't operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. - Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. ELECTRIC SAFETY - Power tool plugs must match the outlet. Never modify the plug in any way. Don't use any adaptor plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock. - Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. - Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. - Don't abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increased the risk of electric shock. - When operating a power tool outdoors, use an extension cord suitable for outdoor use. Using a cord suitable for outdoor use will reduce the risk of electric shock. - If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock. 3 USER MANUAL - Use of power supply via an RCD with a rated residual current of 30mA or less is always recommended. PERSONAL SAFETY - Stay alert, watch what you are doing, and use common sense when operating a power tool. Don't use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. - Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. - Prevent unintentional starting. Ensure the switch is in the off-position before connecting to the power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. - Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. - Don't overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. - Dress properly. Don't wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. - If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. POWER TOOL USE AND CARE - Don't force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the 4 SCROLL SAW rate for which it was designed. - Don't use the power tool if the switch doesn't turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. - Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. - Store idle power tools out of the reach of children and don't allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hand s of untrained users. - Maintain power tools. Check for misalignment or binding of moving parts, breakage o parts, and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. - Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. - Use the power tool, accessories and tool bits, etc. in accordance with the instruction, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. SERVICE - Have your power tool serviced by qualified repair person using only identical replacement parts. This will ensure that the safety of power tool is maintained. - Follow instructions for lubricating and changing accessories. - Keep handles dry, clean, and free from oil and grease. 5 USER MANUAL .CONTENTS OF BOX 4mm hexagon wrench ASSEMBLING THE BLADE FUNCTIONS OF THE MACHINE ON 6 SCROLL SAW SPEED ADJUSTMENT ORIENTATION OF THE BLADE USE OF LIGHTING 7 USER MANUAL USE OF BLOWING SYSTEM ON SAFETY COVER ADJUSTMENT CONNECTING TO VACUUM CLEANER 07 8 SCROLL SAW SETTING OF THE BLADE TENSION CONSUMABLES REPLACING 01 9 USER MANUAL CHANGING OF CARBON BRUSH BLADE CHANGE 10 SCROLL SAW - The blade should have the toothing facing down. ASSEMBLING SOFT SHAFT CLEANING AND MAINTENANCE 1- The use of safety goggles and the safety guard prevent the risk of injury if the blade breaks. 2- Before storing the tool, release tension of the blade. 11 USER MANUAL Nominal frequency and power Nominal power No-load speed Read the Instructions before use Wear Protective eyewear Wear a dust mask Wear hearing protective equipment Use rubber gloves Acoustic pressure level Acoustic pressure level Conforms to CE standards Subjected to recycling Weight Danger 12 SCROLL SAWAdobe PDF Library 15.0 Adobe InDesign 16.3 (Windows)