Instruction Manual for VISUAL COMFORT models including: JN 5301 Alberto Small Open Cage Lantern, JN 5301, Alberto Small Open Cage Lantern, Small Open Cage Lantern, Open Cage Lantern, Cage Lantern, Lantern
Visual Comfort Signature Collection JN 5301AB at Wolff Design Center Plumbing showrooms serving Akron, Medina, Sandusky, and Toledo-Maumee, Ohio since 1965. Casual - Akron-Medina-Sandusky-Toledo-Maumee-Ohio
Visual Comfort Signature Collection JN5301AB Julie Neill Alberto LED 14 inch Antique-Burnished Brass Open Cage Lantern Pendant Ceiling Light, Small
Index of /files/vc/
ASSEMBLY INSTRUCTIONS AB Version Diagram 1 A B C D E F G H E I Bulbs not included Alberto Small Open Cage Lantern Item # JN 5301 NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. TOOLS REQUIRED (NOT INCLUDED): Phillips Screwdriver Slotted Screwdriver Slip Joint Pliers Measuring Tape Wire Strippers Chain Pliers Wire Cutters 1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (D) from chain (H) by removing quick link (E). 3. Install mounting plate (B) to the junction box and secure with mounting screws (C). 4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut. 5. Install canopy (F) to collar loop (D) and secure with collar ring (G). 6. Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain) 7. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E). 8. Thread fixture wire and ground wire through chain (H). NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 9. Separate two sides of molded wire, and strip insulation on each 5/8". 10. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully. 11. Twist all fixture wires together. Slip through center hole of collar loop (D). NOTE: Untwist wires and separate to prepare for connection. M LI ST ED US ASSEMBLY INSTRUCTIONS AB Version Diagram 1 A B C D E F G H E I Bulbs not included Alberto Small Open Cage Lantern Item # JN 5301 NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. 12. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded. 13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A). 14. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections. 15. Make sure all wire connections are tight, then carefully tuck into the junction box. 16. Install canopy (F) to collar loop (D) and secure with collar ring (G). 17. Install light bulbs into the sockets. Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents. M LI ST ED US ASSEMBLY INSTRUCTIONS AGL/PW/ABL Version Diagram 1 A B C D E F G H E I J K Bulbs not included Alberto Small Open Cage Lantern Item # JN 5301 NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. TOOLS REQUIRED (NOT INCLUDED): Phillips Screwdriver Slotted Screwdriver Slip Joint Pliers Measuring Tape Wire Strippers Chain Pliers Wire Cutters 1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (D) from chain (H) by removing quick link (E). 3. Install mounting plate (B) to the junction box and secure with mounting screws (C). 4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut. 5. Install canopy (F) to collar loop (D) and secure with collar ring (G). 6. Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain) 7. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E). 8. Feed wires through hole in frame, then hang cluster (K) to hook (J) on fixture frame. 9. Thread fixture wire and ground wire through chain (H). NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 10. Separate two sides of molded wire, and strip insulation on each 5/8". 11. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully. 12. Twist all fixture wires together. Slip through center hole of collar loop (D). NOTE: Untwist wires and separate to prepare for connection. M LI ST ED US ASSEMBLY INSTRUCTIONS AGL/PW/ABL Version Diagram 1 A B C D E F G H E I J K Bulbs not included Alberto Small Open Cage Lantern Item # JN 5301 NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. 13. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded. 14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A). 15. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections. 16. Make sure all wire connections are tight, then carefully tuck into the junction box. 17. Install canopy (F) to collar loop (D) and secure with collar ring (G). 18. Install light bulbs into the sockets. Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents. M LI ST ED USAdobe PDF library 17.00 Adobe Illustrator(R) 24.0