User Manual for LG models including: ETWCERBS01, YZP-ETWCERBS01, YZPETWCERBS01, ETWCERBS01 RF Module, RF Module
LG Innotek Co., Ltd. ETWCERBS01 YZP-ETWCERBS01 YZPETWCERBS01 etwcerbs01
File Info : application/pdf, 17 Pages, 958.78KB
DocumentDocumentUser Manual PRODUCT NAME : RF Module MODEL NAME : ETWCERBS01 The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. (00)-0073 REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 1 / 15 Index No Description 1 Features 2 Picture of Product 3 Installation Manual 4 Block Diagram 5 Absolute Maximum Ratings 6 Operating Conditions 7 Standard Test Conditions 8 Pin Description 9 Out Drawing 10 Packing Information 11 Certification 12 Regulatory Statement (FCC) 13 Regulatory Statement (ISED) 14 Regulatory Statement (CE) Page 2 2 3 4 4 5 5 6 7 8 10 11 14 15 Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 2 / 15 1. Features ETWCERBS01 is the small size and low power module for IEEE 802.11ac wireless LAN & BT5.0 + HS. ETWCERBS01 is based on Realtek RTL8822CU solution. IEEE 802.11 a/b/g/n/ac 2T2R Dual Band MIMO Bluetooth 5.0+ HS , BLE Size : 18.4 x 27.0 x 2.9mm Two stream spatial multiplexing up to 300Mbps(802.11n) / 867Mbps(802.11ac) Use on-chip OTP (One-Time Programmable) Host Interface : USB2.0 (WLAN & BT) - This model is using the common USB2.0 to control WLAN and BT Security : WAPI, WPA, WPA2 QoS support of WMM 2. Picture of Product Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 3 / 15 3. Installation Manual Install the module like below in the back of the TV TV Main Board ETWCERBS01 installed position Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 4 / 15 4. Block Diagram WiFi1 SW Diplexer SW WiFi2 SW Diplexer BT SW SW DAC ADC DAC ADC RTL8822CU RX I/Q WLAN 2.4G/5G Transceiver TX I/Q RX I/Q TX I/Q BT Transceiver Modem 40MHz Main Clock NV Memory SPS/LDO Regulator MAC Baseband (PHY) BT LE Controller BT BB Controller WLAN MCU PTA BT MCU RAM USB2.0 3.3V 5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Min Max Unit Storage Temperature -10 +80 Storage Humidity (40) - 90 % < Table 1 > . Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 5 / 15 6. Operating Conditions Parameter Min Typ Max Unit Ambient Temperature 0 - 70 Ambient Humidity (40) - - 85 % Supply Voltage 3.135 3.3 3.6 Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temperature Humidity 25 ± 5 65 ± 5% 7-2. Power supply voltages Input power VDD_3.3V Supply Voltage 3.135 ~ 3.6V Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 6 / 15 8. Pin Description Pin SYMBOL I/O 1 NC - 2 NC - 3 NC - 4 NC - 5 GND - 6 WL_USB_DP I/O 7 WL_USB_DN I/O 8 GND - 9 NC DESCRIPTION Not Connect Not Connect Not Connect Not Connect GND USB D+ USB DGND Not Connect 10 NC Not Connect 11 GND 12 NC 13 GND BT_WAKE 14 _HOST HOST 15 _WAKE_BT 16 NC GND Not Connect GND BT CHIP WAKES UP HOST HOST WAKES UP BT CHIP Not Connect Pin SYMBOL I/O DESCRIPTION 17 NC - Not Connect 18 GND - GND 19 NC - Not Connect 20 GND - GND 21 GND - GND 22 NC - Not Connect 23 GND - GND 24 GND - GND 25 GND - GND 26 WLAN_WA KE_HOST O WLAN CHIP WAKES UP HOST 27 NC - Not Connect 28 CHIP_EN I Shutdown CHIP 29 GND - GND 30 VDD33 I 3.3V 31 GPIO5 I/O General Purpose Input/Output Pin 32 GND - GND Note 1. Pin 14 (BT_WAKE_HOST) is pulled up to 3.3V, the port should be configured to be active low Note 2. Pin 15 (HOST_WAKE_BT) is no pull-up or pull-down inside the module Note 3. Pin 26 (WLAN_WAKE_HOST) is pulled up to 3.3V, the port should be configured to be active low Note 4. Pin 28 (CHIP_EN) is pulled up to 3.3V, do not pull up on Host Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 7 / 15 9. Outline Drawing 3D View Copyright. 2021. All Rights Reserved. '21. 02. 08 K.S Lee '21. 02. 08 T.G Jang '21. 02. 08 S.D Chol ETWCERBS01 REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 8 / 15 10.Packing Information Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 9 / 15 Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 10 / 15 11.Certification Brand : LG Innotek Manufacturer Address : E1/E3, 30, Magokjungang 10-ro, Gangseo-gu, Seoul, 07796, Korea Product Name : WiFi Factory : PT. LG INNOTEK INDONESIA Factory Address : Bekasi International Industrial Estate, Blok C8 NO. 12 & 12 A, Desa Cibatu, Cikarang Selatan, Bekasi 17750 Indonesia : () () : ( ) (ETWCERBS01) : 2021. 07 : () / : R-C-LGW-ETWCERBS01 : -20 ~ 50 °C * Connection and use of this communications equipment is permitted by the Nigerian Communications Commission Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 11 / 15 12. Regulatory Statement (FCC) Part 15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the follow ing two conditions: (1) this device may not cause harmful interference, and (2) this dev ice must accept any interference received, including interference that may cause unde sired operation. Part 15.105 Statement (Class B) This equipment has been tested and found to comply with the limits for a Class B digi tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferenc e in a residential installation. This equipment generates, uses and can radiate radio fr equency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee t hat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turni ng the equipment off and on, the user is encouraged to try to correct the interference b y one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the rece iver is connected. - Consult the dealer or an experienced radio/TV technician for help. Part 15.21 Statement Any changes or modifications not expressly approved by the party responsible for co mpliance could void the user's authority to operate this equipment. This device must n ot be co-located or operating in conjunction with any other antenna or transmitter. Responsible Party Information (Supplier's Declaration of Conformity) LG Innotek USA Inc. Street Address 2540 N 1st ST STE 400 SAN JOSE, CA 95131-1016 PHONE : +1-408-350-7661 / FAX : +1-408-955-0329 Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 12 / 15 12. Regulatory Statement (FCC) Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manua l v01 List of applicable FCC rules This module has been granted modular approval as below listed FCC rule parts. - FCC Rule parts 15C (15.247) Summarize the specific operational use conditions The OEM integrator should use equivalent antennas which is the same type and equal o r less gain then an antenna listed in this instruction manual. RF exposure considerations The module has been certified for integration into products only by OEM integrators und er the following condition: -The antenna(s) must be installed such that a minimum separation distance of at least 2 0 cm is maintained between the radiator (antenna) and all persons at all times. -The transmitter module must not be co-located or operating in conjunction with any othe r antenna or transmitter except in accordance with FCC multi-transmitter product proced ures. -Mobile use As long as the three conditions above are met, further transmitter testing will not be requi red. OEM integrators should provide the minimum separation distance to end users in th eir end-product manuals. Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 13 / 15 12. Regulatory Statement (FCC) Antennas list This module is certified with the following external antenna. Frequency 2402 ~ 2480 MHz (BT) 2412 ~ 2472 MHz (WLAN 2.4 GHz) 5180 ~ 5825 MHz (WLAN 5 GHz) Antenna type & Peak gain HQ Antenna type: Diplole antenna (Peak Gain : 2.93 dBi) IP Antenna type: Diplole antenna (Peak Gain : 2 dB) 01 Antenna type: Planar Inverted F antenna (Peak Gain : 3.35 dBi) A7 Antenna type: Diplole antenna (Peak Gain: 2 dBi) 01 Antenna type: Planar Inverted F antenna : 5.37 dBi(UNII 1)/ 5.57 dBi(UNII 2A) : 5.63 dBi(UNII 2C)/ 5.39 dBi(UNII 3) A7 Antenna type: Diplole antenna (Peak Gain: 2 dBi) : 2.00 dBi(UNII 1) / 2.00 dBi(UNII 2A)/ : 2.00 dBi(UNII 2C)/ 2.00 dBi(UNII 3) Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure. Label and compliance information End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID a nd IC Certification Number are not visible when the module is installed inside another de vice, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labele d in a visible area with the following: Contains FCC ID: YZP-ETWCERBS01 Contains IC: 7414C- ETWCERBS01 Information on test modes and additional testing requirements OEM integrator is still responsible for testing their end-product for any additional complia nce requirements required with this module installed (for example, digital device emissio ns, PC peripheral requirements, additional transmitter in the host, etc.). Additional testing, Part 15 Subpart B disclaimer The final host product also requires Part 15 subpart B compliance testing with the modul ar transmitter installed to be properly authorized for operation as a Part 15 digital device. OEM integrator must install this transmitter module inside the enclosure of host device n ot to be user accessible to compliance with antenna requirements in FCC Rule Section 15.203. Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 14 / 15 13. Regulatory Statement (ISED) RSS-GEN, Sec. 7.1.3(licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation i s subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause unde sired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance min imum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. Attention: Les changements ou modifications de cet appareil non expressément approuvé par le fabricant peuvent annuler votre droit à utiliser cet équipement. l'exposition aux RF L'antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une dis tance minimum de au moins 20 cm entre la source de radiation (l'antenne) et toute pers onne physique. Étiquetage du produit final (IC) Le module ETWCERBS01 est étiqueté avec sa propre identification FCC et son propre numéro de certification IC. Si l'identification FCC et le numéro de certification IC ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre dispositif, la partie exter ne du dispositif dans lequel le module est installé devra également présenter une étiquet te faisant référence au module inclus. Dans ce cas, le produit final devra être étiqueté su r une zone visible avec les informations suivantes: Contient module émetteur identification FCC ID: YZP-ETWCERBS01 Contient module émetteur IC : 7414C-ETWCERBS01 "The 5150-5250 MHz band is restricted to indoor use only." Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 15 / 15 13. Regulatory Statement (ISED) Antennas list This module is certified with the following external antenna. Frequency 2402 ~ 2480 MHz (BT) 2412 ~ 2472 MHz (WLAN 2.4 GHz) 5180 ~ 5825 MHz (WLAN 5 GHz) Antenna type & Peak gain HQ Antenna type: Diplole antenna (Peak Gain : 2.93 dBi) IP Antenna type: Diplole antenna (Peak Gain : 2 dB) 01 Antenna type: Planar Inverted F antenna (Peak Gain : 3.35 dBi) A7 Antenna type: Diplole antenna (Peak Gain: 2 dBi) 01 Antenna type: Planar Inverted F antenna : 5.37 dBi(UNII 1)/ 5.57 dBi(UNII 2A) : 5.63 dBi(UNII 2C)/ 5.39 dBi(UNII 3) A7 Antenna type: Diplole antenna (Peak Gain: 2 dBi) : 2.00 dBi(UNII 1) / 2.00 dBi(UNII 2A)/ : 2.00 dBi(UNII 2C)/ 2.00 dBi(UNII 3) Copyright. 2021. All Rights Reserved. REG. DATE : 2021.04.23 REV. DATE : 2021.04.23 DOCUMENT No : - S P E C I F I C A T I O N MODEL NAME : ETWCERBS01 REV.NO : 1.0 PAGE : 16 / 15 14. Regulatory Statement (CE) Simplified EU Declaration of Conformity "Hereby, LG Innotek Co., Ltd. declares that the radio equipment type RF Module is in co mpliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is a vailable at the following internet address: http://www.lginnotek.com/en/compliance-infor mation. The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be collocated or operating in conjunction with any other antenna or transmitter. The host manufacturer integrating this module should be assessed total com pliance with all essential requirements regarding this radio module. The use of the 5150 5350 MHz band is restricted to indoor use only. This restriction will be applied in all member states. The host manufacturer has the responsibility that the host device should be compliance with all essential requirement of RED. The product is compliant with the RED Article 10(2) because the product is operated at least one Member State without infringing applicable requirements on the use of radio spectrum. Manufacturer Name: LG Innotek Co., Ltd. Manufacturer Address: 26, Hanamsandan 5beon-ro, Gwangsan-gu, Gwangju, 506-731, Korea LG Innotek Co., Ltd, Europe Branch Output power Tune-up value (CE) Item Standard 2.4 G Frequency 5G Low 5G High Frequency 2 412 ~ 2 472 MHz 5 150 ~ 5 250 MHz 5 250 ~ 5 350 MHz 5 470 ~ 5 725 MHz 5 725 ~ 5 850 MHz Target. Power (EIRP, Sum) IEEE 802.11 a/b/g/n/ac 16.5 dBm 19.5 dBm 16.9 dBm 10.6 dBm Item BT BT LE Frequency 2 402 ~ 2 480 MHz 2 402 ~ 2 480 MHz Target. Power (EIRP) 6.5 dBm 4.5 dBm Copyright. 2021. All Rights Reserved. Tolerance ±3dBm ±3dBmMicrosoft PowerPoint 2013 Microsoft PowerPoint 2013