Installation Guide for iBoard models including: IB-P097, P098C, IB-P097 Black Running Boards Style, IB-P097, Black Running Boards Style, Running Boards Style, Boards Style
APS Black Running Boards Style Compatible with Toyota Tundra 2007-2021 CrewMax (Nerf Bars Side Steps) 6in Wide Aluminum : Automotive
iBoard® iBoard® by APS READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. *ROCKER PANEL MOUNT *NO DRILLING REQUIRED PART#: IB-P097/P098C&J Fastener Size Tightening Torque (ft-lbs) 6mm 6-7 8mm 16-18 10mm 31-32 12mm 56-58 14mm 92-94 Required X X X X PART LIST Driver Side Step Bar Front Passenger Side Step Bar 1# 2# 3# 3# 3# 3# 3# 3# Customer Support: info@iboardauto.com 1 Rev. 20230801 iBoard® Hardware Package A (For Bracket Installation) Item QTY Description Item QTY Description 1# 1 Driver Front Mounting Bracket 4# 16 M81.25-30mm Hex Bolts 2# 1 Passenger Front Mounting Bracket 5# 16 M8 Flat Washers 3# 6 Mounting Brackets 6# 16 M8 Lock Washers 4 # 5 # 6 # Item QTY Hardware Package B (For Step Bar Installation) Description Item QTY Description 1# 16 M8X1.25-35mm Carriage Bolts 3# 16 M8 Nylon Lock Nuts 2# 16 M8 Large Flat Washers 4# 8 Sliders (Packed with Mounting Brackets) 1 # 2 # 3 # 4 # Customer Support: info@iboardauto.com 2 Rev. 20230801 iBoard® STEP 1 Start installation from the driver side of the vehicle. Select the Driver Front Mounting Bracket. Attach the Bracket to the vehicle using the included (2) M8x1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Flat Washers, (Fig 1). Do not fully tighten hardware at this time. STEP 2 Move to the driver side center, center 1 and rear mounting locations. Repeat Step 1 to install the Driver Center & Center 1 & Rear Mounting Brackets, (Fig 1). Mounting Bracket Mounting Bracket Front Mounting Bracket Driver Front Mounting Bracket (8) M8x1.25-30mm Hex Bolts (8) M8 Lock Washers (8) M8 Flat Washers (Fig 1) Driver Side Mounting Brackets Installation (Example) Customer Support: info@iboardauto.com 3 Rev. 20230801 iBoard® STEP 3 Once all (4) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 2 & 3) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (3) sliders to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (8) M8 Large Flat Washers and (8) M8 Nylon Lock Nuts and (4) Sliders, (Fig 3). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Mounting Bracket. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-3 for the other side Step Bar installation. The installation is completed!!! Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. Slider (2) Carriage Bolts (Fig 2) Slider Installation Slider with (2) Carriage Bolts Step Bar Slider (w/ installed Carriage Bolts) Step Bar (Bottom View) Mounting Bracket (2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts (Fig 3) Step Bar Installation Customer Support: info@iboardauto.com 4 Rev. 20230801Microsoft Publisher LTSC