Installation Guide for Skydance models including: DH4 Lighting Control System, DH4, Lighting Control System, Control System
DH4 DALI/DMX 4-Channel Switch 4 DALI address, 4 channel 16Adry contact mains rated relay switch output. OLEDdisplayscreen, via button settingtwoworkmode: DALImode, DMXmode. DALI address can be manually assigned and shown in digital display or automatically assigned by DALI master. In accordance with DALI standard protocol IEC 62386-101,102, 208 and in compliance with DALI products from other international incorporation. Comply with the DMX512 standard protocols. RDM function can realize intercommunication between DMX master and decoder. Supports manual switching of individual channels. High-inrush specification relays (single pole, normally open). Zero cross switching function. Can operate as: 4 individual channels (4 × 1) 2 sets of 2 channels (2 × 2) 1 sets of 4 channels (1 × 4) DALI Switch 4CH/ dry contact output / 4 DALI address/ DMX-RDM / OLEDdisplay / Din Rail Technical Parameters InputandOutput Input voltage 100-240VAC Input current 0.1A Input signal DALI+DMX512 No-load standby power consumption 0.5W@100V, 1.5W@240V Full load loss power 4W@100V, 4.5W@240V Relay contacts High inrush (120 A at 20ms), single-pole, single-throw (SPST) relay. Max relay load current 16A resistive load (incandescent lamp) 8A Capacitive load (LED dimming driver) 8A inductive load ( uorescent lamp) Safety and EMC EMC standard (EMC) ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 Safety standard(LVD) EN 62368-1:2020+A11:2020 Certi cation CE,EMC,LVD Warranty and Protection Warranty 5 years Environment Operation temperature Case temperature (Max.) IP rating Package Size Gross weight Ta: -20 OC ~ +50 OC Tc: +60 OC IP20 W118 x L102 x H71mm 0.345kg Mechanical Structures and Installations 2CH drycontactoutput 1CH drycontactoutput 3CH drycontactoutput 4CH drycontactoutput AC N Input AC L Input OLEDdispay screen Settingkey Two groups of DALI signal input DALI bus no need distinguish plus-minus polarity DALIcom LEDindicator 115.00mm L N 100-240VAC IN K1A 1 K1B K2A 2 K2B K3A 3 K3B K4A 4 K4B DH4 DALI/DMX 4-Channel Switch 4 ChannelON/OFFLEDindicator DALI IN DALI OUT DA1 DA2 DA1 DA2 DALI COM K1 K2 K3 Uin = 100-240VAC Iin = 0.1A Out = 4×16A Temp Range: -20~+55 DMX IN DMX OUT GND D- D+ GND D- D+ K4 DMX Signal RJ45 Pin1: D+ Pin2: DPin7: GND Pin8: GND 4 Channel manual switch RJ45 DMX signal input DMX COM DMXinput DMX output DMX comLEDindicator 88.00mm 88.00mm 65.00mm User Manual Ver 1.0.0 2023.7 DIN Rail Mounting Size: TS-35/7.5 or TS-35/15 Page1 Wiring Diagram LN AC100-240V L N 100-240VAC IN K1A 1 K1B K2A 2 K2B K3A 3 K3B K4A 4 K4B DALI IN DALI OUT DA1 DA2 DA1 DA2 DALI COM K1 K2 K3 DMX IN DMX OUT GND D- D+ GND D- D+ K4 DMX Signal RJ45 Pin1: D+ Pin2: DPin7: GND Pin8: GND DMX COM DALI Master DMX Master DMX signal Note: The maximum surge current of the AC output is120A, the sum of surge current of multiple resistivel load or inductive load (LED drivers )should not exceed its maximum value. Otherwise, the product will be overloaded and damaged. WorkMode 1.Systemsetting System Setting WorkMode:DALI Channe1Num:4 ManualSwitch:Yes Long press M button for 2s, enter system setting state, prepare to set the working mode, channel number and manual switch enable. Short press the M button to switch three setting items. Working mode: Short press or button, switch between DALI and DMX working mode. Channel number: Short press or button, switch the number of 4/2/1 channels, i.e. 4 independent channels (4x1), 2 groups of 2 channels (2x2) or 1 group of 4 channels (1x4). Manual switch enable: Short press or button, setting to allow (Yes) or disallow (No) the manual switching function, i.e. setting whether the four-channel manual switching buttons are active or not. Long press M button for 2s, or timeout 15s, quit system setting. 2.DALI mode DALI Mode CH1:01 CH2:02 CH3:03 CH4:04 In DALI mode, the DALI address can be set by buttons or DALI master control: (1) Set DALI Address via buttons Short press M button, prepare for set the start DALI address. The four channels can be addressed separately, and the address setting of the four channels can be switched sequentially by short pressing the M button. Short press or button, change the address value of the current channel (00-63-FF), FF means unassigned DALI address. long press for fast adjustment. Long press M button for 2s, or timeout 15s, quit DALI address setting. (2) DALI address assigned by DALI masters DALI address can also be assigned by DALI Master controller automatically. Please refer to user manuals of compatible DALI Masters for speci c operations. 3.DMX mode DMX Mode CH1:001 CH2:002 CH3:003 CH4:004 In DMX mode, the DMX address can be set by buttons or DMX RDM master: Short press M button, prepare for set the start DMX address. Only the address of the rst channel needs to be set, and the addresses of the other channels will be automatically added 1 in sequence. Short press or button, change the DMX address value (001-512), long press for fast adjustment. Long press M button for 2s, or timeout 15s, quit DMX address setting. 4.Restore factory settings Reset Long press and buttons at the same time for 2 seconds to restore factory settings. Factory default parameter: DALI mode, number of channels is 4, manual switch enable. 5.Overheat protection Temp Faults 110°C triggers temperature protection and shuts off the relay output. Normal switching control is resumed at 90°C. User Manual Ver 1.0.0 2023.7 Page2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6