User Manual for HDMI models including: HD-C-SPB14D60, 18Gbps HDMI 1 4 Splitter Over 60m Cat
1. Introduction 2. Features 3. Package Contents ① 1× 18Gbps 1×4 HDMI Splitter over 60m CAT ② 4× CAT Receiver ③ 1× IR Blaster Cable (1.5 meters)
⑥ 1× User Manual The 18Gbps HDMI 1x4 Splitter can distribute 1 HDMI source signal to any 4 display devices. Support video resolution up to 4K2K@50/60Hz 4:4:4. It is designed with 1 HDMI loop output and 4 CAT outputs. The HDMI signal transmission distance can be extended up to 35 meters at the resolution of
File Info : application/pdf, 13 Pages, 6.21MB
DocumentDocument18Gbps HDMI 1×4 Splitter over 60m CAT VER 1.1 Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Table of Contents 1. Introduction........................................................................................... 1 2. Features................................................................................................. 1 3. Package Contents................................................................................1 4. Specifications....................................................................................... 2 5. Operation Controls and Functions...................................................... 3 5.1 Transmitter....................................................................................... 3 5.2 CAT Receiver...................................................................................5 5.3 IR Pin Definition................................................................................6 6. EDID Mode.............................................................................................7 7. ASCII Commands................................................................................. 8 8. Application Example............................................................................11 1. Introduction The 18Gbps HDMI 1x4 Splitter can distribute 1 HDMI source signal to any 4 display devices. Support video resolution up to 4K2K@50/60Hz 444. It is designed with 1 HDMI loop output and 4 CAT outputs. The HDMI signal transmission distance can be extended up to 35 meters at the resolution of 4K2K@60Hz, or 50 meters at 4K2K@30Hz, or 60 meters at 1080P@60Hz via a single CAT6/6a/7 cable. The product supports one-way IR control signal pass-through audio extract function and advanced EDID management. 2. Features HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant Support 18Gbps video bandwidth Support video resolution up to 4K2K@50/60Hz 444 Support HDR, HDR10+, HLG and Dolby vision Support up to 7.1CH HD audio pass-through Support digital and analog audio de-embedded output Extend the signal transmission distance up to 35 meters at the resolution of 4K2K@60Hz, 50 meters at 4K2K@30Hz, 60 meters at 1080P@60Hz via a single CAT6/6a/7 cable Support 1 HDMI input, 1 HDMI loop output and 4 CAT outputs. Support one-way IR control signal pass-through Advanced EDID management Support one-way PoC function (only from transmitter to receiver) Compact design for easy and flexible installation 3. Package Contents 1× 18Gbps 1×4 HDMI Splitter over 60m CAT 4× CAT Receiver 1× IR Blaster Cable (1.5 meters) 4× 20K~60KHz IR Receiver Cable (1.5 meters) 1× 12V/2.5A DC Locking Power Adapter 1× User Manual -1- 4. Specifications Technical HDMI Compliance HDCP Compliance Video Bandwidth HDMI 2.0b HDCP 2.2/1.x 594MHz/18Gbps Video Resolution Up to 4k2k@50/60Hz 4:4:4 Color Depth 8-bit,10-bit,12-bit(1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4) 8-bit,10-bit,12-bit(4K2K@60Hz YCbCr 4:2:2/4:2:0) Color Space RGB, YCbCr 4:4:4 / 4:2:2. YUV 4:2:0 HDR Support HDR10, HDR10+, HLG, Dolby vision LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, HDMI Audio Formats Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X Coaxial Audio Formats PCM2.0, Dolby Digital / Plus, DTS 2.0/5.1 Analog Audio Formats PCM 2.0CH ESD Protection Human body model--±8kV (Air-gap discharge) & ±4kV (Contact discharge) Connection Input Output Control 1×HDMI Type A (19-pin female) 1×HDMI Type A (19-pin female 4x CAT OUT [RJ45, 8-pin female] 1x Coaxial Audio OUT [RCA] 1x L/R Audio OUT [3.5mm Stereo Mini-jack] 1×SERVICE (Micro USB, Update port 1x EDID DIAL switch [5-pin] 1x IR OUT [3.5mm Stereo Mini-jack] -2- Mechanical Housing Silkscreen Color Dimensions Weight Power Supply Power Consumption Operation Temperature Storage Temperature Relative Humidity Metal Enclosure Black Transmitter: 210mm (W) × 100mm (D) × 25mm (H) Receiver: 88mm (W) × 61mm (D) × 18mm (H) Transmitter: 617g Receiver:155g Input: AC100 - 240V 50/60Hz, Output: DC 12V/2.5A (US/EU standards, CE/FCC/UL certified) 14W 0°C ~ 40°C / 32°F ~ 104°F -20°C ~ 60°C / -4°F ~ 140°F 20~90% RH (non-condensing) 5. Operation Controls and Functions 5.1 Transmitter Panel Front Panel ON 18Gbps HDMI 1x4 Splitter over 60m CAT OFF IN LOOP 1 2 3 4 OUT 1 2 34 5 No. Name Function Description 1 POWER switch Press this switch to power on/off the device. 2 POWER LED When the device is powered on, the red power LED will be on. 3 IN LED When the HDMI IN port connects an active source device, the green LED will be on. 4 LOOP LED 5 OUT LED (1~4) When the HDMI LOOP OUT port connects an active Wh3en td4hiespC1laA/y5TdOeUviTcPe,UtThepogrrteceonnnLeEcDtswthillebCeAoTn.IN port of CAT receiver, the corresponding green OUT LED will be on. -3- Rear Panel 1 2 3 4 IN LOOP OUT OUT AUDIO OUT HDMI CAT OUTPUT IR DC 12V 1 2 3 4 56 7 No. Name Function Description 1 AUDIO OUT Coaxial/analog audio output port, connect to amplifer (COAX, L/R) or speaker. 2 HDMI port IN: HDMI input port, connect to HDMI source device such as DVD or set-top box with an HDMI cable. LOOP OUT: HDMI loop output port, connect to the HDMI display device such as TV or Monitor with an HDMI cable. 3 CAT OUTPUT Connect to the CAT IN port of the CAT receiver with port (1~4) a CAT cable. 4 Link Signal Indicator lamp (Green) Illuminate: T1r/a5nsmitter and receiver Dar3k: T4ransmitter and receiver are are not connected. connected. Data Signal Illuminating: HDMI signal with HDCP. 5 Indicator lamp Flashing: HDMI signal without HDCP. (Orange) Dark: No HDMI signal. 6 IR OUT Connect the IR Blaster cable to transmit IR signal from the CAT receiver. 7 DC 12V Plug the DC 12V power supply into the unit and connect the adaptor to an AC outlet. (Note: The transmitter can power the receiver via a CAT cable.) Side Panel 1 0 EDID SERVICE 1 2 No. Name Function Description 1 EDID DIAL switch Used to set EDID mode. Please refer to Section "6. EDID Mode" for details. 2 SERVICE port Used for firmware update or serial port command control. Please refer to "7. ASCII Commands". -4- 5.2 CAT Receiver HDMI OUT CAT IN SERVICE IR IN DC 12V 1 3 24 5 6 7 No. Name 1 HDMI OUT 2 CAT IN Function Description HDMI output port, connect to HDMI display device such as TV or Projector with an HDMI cable. Connect to the CAT OUTPUT port on the transmitter with a CAT cable. 3 Power Indicator When the receiver is powered on, the power indicator Lamp (Green) lamp will be on. Data signal Illuminating: HDMI signal with HDCP. 4 Indicator Lamp Flashing: HDMI signal without HDCP. (Orange) Dark: No HDMI signal. 5 SERVICE port Used for firmware update. 6 IR IN Connect to the IR Receiver cable. The IR signal will send to the IR OUT port of the transmitter. 7 DC 12V Plug DC 12V/1A power supply into the unit and connect the adapter to an AC outlet. (Note: The CAT receiver also can be powered by the transmitter via a CAT cable. ) -5- 5.3 IR Pin Definition IR Receiver IR Blaster IR Receiver IR Blaster IR Blaster Signal Power NC IR Signal Power Grounding Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters. -6- 6. EDID Mode The defined EDID setting list of the product is shown as below: EDID Mode EDID Description 11111 1080P, Stereo Audio 2.0 11110 1080P, Dolby/DTS 5.1 11101 1080P, HD Audio 7.1 11100 1080I, Stereo Audio 2.0 11011 1080I, Dolby/DTS 5.1 11010 1080I, HD Audio 7.1 11001 1080P 3D, Stereo Audio 2.0 11000 1080P 3D, Dolby/DTS 5.1 10111 1080P 3D, HD Audio 7.1 10110 4K2K30Hz_444, Stereo Audio 2.0 10101 4K2K30Hz_444, Dolby/DTS 5.1 10100 4K2K30Hz_444, HD Audio 7.1 10011 4K2K60Hz_420, Stereo Audio 2.0 10010 4K2K60Hz_420, Dolby/DTS 5.1 10001 4K2K60Hz_420, HD Audio 7.1 10000 4K2K60Hz_444, Stereo Audio 2.0 01111 4K2K60Hz_444, Dolby/DTS 5.1 01110 4K2K60Hz_444, HD Audio 7.1 01101 4K2K60Hz_444, Stereo Audio 2.0 HDR 01100 4K2K60Hz_444, Dolby/DTS 5.1 HDR 01011 4K2K60Hz_444, HD Audio 7.1HDR 01010 COPY_FROM_LOOP OUT 01001 01000 COPY_FROM_CAT OUT1 COPY_FROM_CAT OUT2 00111 COPY_FROM_CAT OUT3 00110 COPY_FROM_CAT OUT4 00101 1080P, Stereo Audio 2.0 00100 1080P, Stereo Audio 2.0 00011 1080P, Stereo Audio 2.0 00010 1080P, Stereo Audio 2.0 00001 1080P, Stereo Audio 2.0 00000 PC control mode -7- 7. ASCII Commands The product also supports ASCII command control. Connect the SERVICE port of the product to a PC with an USB cable. Then, open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below. ASCII Commands Serial port protocol. Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check bit: 0 x - Parameter 1 y - Parameter 2 ! - Delimiter Command Code Power Function Description Example Feedback Power on Default Setting s power z! r power! s reboot! Power on/off the device,z=0~1 s power 1! (z=0 power off, z=1 power on) Get current power state Reboot the device r power! s reboot! System Initializing... power on Initialization Finished! FW version x.xx.xx power on/power off reboot System Setup help! r type! List all commands Get device model help! r type! HDC-SPB14D60 r status! r fw version! Get device current status Get Firmware version r status! r fw version! Get the unit all status: power, in/out connection, edid mode MCU BOOT: Vx.xx.xx MCU APP: Vx.xx.xx r link in! Get the connection status of the input port r link in! HDMI IN: connect r link out y! Get the connection status of the y output port y=0~4(0=all, 1~4=CAT 1~4) r link out 1! CAT OUT1: connect r link loop out y! Get the connection status of the y loop output porty=1 s reset! Reset to factory defaults r link loop out 1! HDMI LOOP OUT: connect Reset to factory defaults s reset! System Initializing... Initialization Finished! FW version x.xx.xx -8- Command Code Function Description Example Feedback Default Setting Output Setting Set hdmi loop output stream s hdmi stream z! on/off z=0~1(0:disable,1:enable) Enable hdmi loop out s hdmi stream 1 ! stream Disable hdmi loop out enable stream Enable cat output 1 stream Disable cat output 1 s cat y stream z! Set cat output y stream on/off, y=0~4(0=all) z=0~1 s cat 1 stream 1 ! stream Enable cat all outputs enable (0:disable,1:enable) s cat 0 stream 1 ! stream Disable cat all outputs stream r hdmi stream! Get hdmi loop out stream status r hdmi stream! Enable hdmi loop output stream r cat y stream! Get cat output y=0~4(0=all) y stream status, r cat 1 stream! Enable cat output 1 stream s hdmi hdcp z! set hdmi loop output port hdcp s hdmi hdcp 1! status hdmi loop out hdcp on all hdmi out hdcp active r hdmi hdcp! Get HDCP status of loop out r hdmi hdcp! hdmi loop out hdcp on s cat y hdcp z! set cat output y port hdcp status y=0~2(0=all) z=0~1 (1=on,0=off) s cat 1 hdcp 1! cat out 1 hdcp on all cat out hdcp active r cat y hdcp! Get HDCP status of cat out y, y=0~2(0=all) r cat 1 hdcp! cat out 1 hdcp on set cat output y port dsc mode s cat y dsc mode z! status y=0~4(0=all) z=1~3 (1=Cat cable distance normal s cat 1 dsc Mode, 2= Cat cable distance mode 2! 35M Mode,3= Cat cable Cat cable cat out 1 dsc mode 2 distance 35M Mode(35M) distance 70M Mode) r cat y dsc mode! Get dsc mode y=0~4(0=all) of cat out y, r cat 1 dsc mode! cat out 1 dsc mode 2 s audio mute 1! set audio output port mute status (1-mute, 0-umute) s audio mute 1! s audio mute 1 s audio unmute (0) r audio mute! Get audio output mute status r audio mute! audio mute 1 -9- Command Code Function Description Example Feedback Default Setting EDID Setting Set input EDID from default EDID z, z=1~26 1 1080p,Stereo Audio 2.0 2 1080p,Dolby/DTS 5.1 3 1080p,HD Audio 7.1 4 1080i,Stereo Audio 2.0 5 1080i,Dolby/DTS 5.1 6 1080i,HD Audio 7.1 7 3D,Stereo Audio 2.0 8 3D,Dolby/DTS 5.1 9 3D,HD Audio 7.1 10 4K2K30_444, Stereo Audio 2.0 11 4K2K30_444, Dolby/DTS 5.1 input EDID:1080p, 12 4K2K30_444,HD Audio 7.1 Stereo Audio 2.0 13 4K2K60_420, s edid in from z! Stereo Audio 2.0 14 4K2K60_420, s edid in from 1! Dolby/DTS 5.1 15 4K2K60_420,HD Audio 7.1 Please toggle EDID 16 4K2K60_444, dip switch to 00000! Stereo Audio 2.0 17 4K2K60_444, Dolby/DTS 5.1 18 4K2K60_444,HD Audio 7.1 19 4K2K60_444, Stereo Audio 2.0 HDR 20 4K2K60_444, Dolby/DTS 5.1 HDR 21 4K2K60_444, HD Audio 7.1 HDR 22 copy from hdmi loop out 23 copy from cat output 1 24 copy from cat output 2 25 copy from cat output 3 26 copy from cat output 4 1080p,Stereo Audio 2.0 r edid in! r edid in data! Get EDID status of the input r edid in! Get the EDID data of the hdmi r edid in data! input input EDID: 4K2K60_ 444,Stereo Audio 2.0 EDID data : 00 FF FF FF FF FF FF 00 ...... -10- 8. Application Example DVD or Blu-ray Player UHDTV Power Supply AUDIO OUT 1 IN LOOP OUT HDMI Transmitter 2 3 4 CAT OUTPUT LAN OUT IR DC 12V 2.0 Speakers Amplifier HDMI OUT Cat 6/6a/7 LAN CAT IN SERVICE IR IN DC 12V IR Blaster Receiver UHDTV IR Receiver The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. -11-Adobe PDF library 10.01 Adobe Illustrator CC 23.0 (Windows)