Mobile Power Supply (with Wireless Charge)

Specifications

Package Contents

• [Power Bank Icon] Power Bank x1
• [Charging Cable Icon] Charging Cable x1
• [User Manual Icon] User Manual x1

Product Features

Product features are illustrated with numbered callouts. See list below:

• 1. Wireless Charging Indicator [Wireless Indicator] ?
• 2. 4-Level Power Indicators [Power Level Indicators] ?
• 3. Power Button [Power Button] ?
• 4. USB Output Port [USB Output Port] ?
• 5. Type-C Input & Output Port [Type-C Port] ?
• 6. Folding Phone Stand [Phone Stand] ?
• 7. Wireless Charging Area and Magnetic Adsorption Ring [Wireless Charging Pad] ?

Operating Instructions

1. Charging the power bank ⚡️

Connect the Type-C cable (included) between the power bank and a wall charger or power adapter (not included). Charging will start automatically. It is recommended to use a PD22.5W wall charger or power adapter for fast charging.

During charging, the power indicators will flash. Each LED light indicates approximately 25% of the available battery capacity. When fully charged, all power indicators will remain on.

Note ?: Fully charge the power bank before using it for the first time. Recharge the power bank once every three months when not in use or seldom used.

2. Charging the device ⚡️

1. Wired Charging ?

Press the power button; the power indicators will turn on. Connect the charging cable between the USB or Type-C port of the power bank and the device to start charging. The power indicators will remain on during device charging.

2. Wireless Charging ?

Place the device in the center of the wireless charging area. If your device supports MagSafe technology, the power bank will automatically hold it due to strong magnets. Press the power button; the wireless charging indicator will turn on, signifying that wireless charging is in progress.

Note ?: Ensure your device is compatible with Qi standard receiving equipment.

Troubleshooting

1. If the first power indicator is flashing after pressing the power button, it means the battery is running low and needs recharging ⚠️.
2. The power bank automatically identifies devices that need charging. If no device is being charged, the power bank will turn off after 30 seconds ?.
3. For wireless charging, your device must be equipped with a Qi wireless receiver. The power bank automatically identifies Qi-compatible devices. If the center point of the receiving terminal is deflected over 8-10mm from the center point of the transmitting terminal, the power bank will turn off automatically ↔️.
4. If wired charging is not working properly, try using a different charging cable, as the connector may be loose ?.
5. During charging, the device may become warm ? due to high currents and resistance, especially during wireless charging. To reduce temperature, avoid running intensive applications or using GPS on your mobile device while charging.

Cautions ⚠️

1. The power bank generates heat ?. Always charge in a well-ventilated ?️ and open-air area.
2. Do not charge under pillows, blankets, clothing, or on flammable surfaces ⚠️. Keep the power bank away from heat sources ?, direct sunlight ☀️, combustible gas ?, humidity ?, water ?, or other liquids.
3. Do not disassemble ?️, open, microwave ♨️, incinerate ?, paint, or insert foreign objects into the power bank.
4. Do not subject the power bank to mechanical shock ? such as crushing, bending, puncturing, or shredding. Avoid dropping ⬇️ or placing heavy objects on the power bank.
5. Do not short-circuit ⚡️ the power bank or store it in a receptacle where it may be short-circuited by other metallic or conductive objects.
6. Do not operate the power bank if it has been wet ? or damaged to prevent electric shock, explosion, and/or injury.
7. Keep the power bank dry ?️ to avoid short circuits ⚡️ or other damage to electronic components.
8. Keep the power bank away from high heat ? and flammable liquids ⛽️ and gasses. Avoid using in environments with temperatures above 45°C or below 0°C ?️.

FCC Warning ?

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference ?, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy ? and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications ?. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception ?, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures ?️:

• Reorient or relocate the receiving antenna ?.
• Increase the separation between the equipment and receiver ↔️.
• Connect the equipment into an outlet ? on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician ?‍? for help.

NOTE 2: Any changes or modifications ⚙️ to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment ?.

The device has been evaluated to meet general RF exposure ☢️ requirement. The device can be used in portable exposure condition without restriction.