Sub-Zero, Wolf, and Cove | Kitchen Appliances that Inspire
Shop Quality Grill Parts & Appliance Parts – Over 25,000 ModelsWolf Microwave Parts - Select From 13 Models
Instruction Manual for WOLF models including: MWD24-2U-S, MWD24-2US Drawer Microwave, MWD24-2U, MWD24-2U Drawer Microwave, MWD24-2S, MWD24-2S Drawer Microwave, Drawer Microwave, Microwave
Wolf MWD24-2U/S Parts | Microwaves
File Info : application/pdf, 13 Pages, 385.30KB
DocumentDocumentThis Owner's Manual is provided and hosted by Appliance Factory Parts. Wolf MWD24-2U/S Owner's Manual Shop genuine replacement parts for Wolf MWD24-2U/S Find Your Wolf Microwave Parts - Select From 13 Models -------- Manual continues below -------- D RAWER M ICROWAVE I NSTALLATION I NSTRUCTIONS C O N TAC T I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance.com WOLF® is a registered trademark of Wolf Appliance, Inc. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. W O L F DRAWER MICROWAVE I N S TA L L AT I O N R E Q U I R E M E N T S IMPORTANT NOTE: This installation must be completed by a qualified installer or Wolf authorized service center technician. Save this installation manual for local electrical inspector's use. Read and save these instructions for future reference. I NSTA LL E R Read all of the Installation Instructions before installing the drawer microwave. Remove all packing material before connecting the electrical supply. Observe all governing codes and ordinances. Be sure to leave these instructions with the consumer. CONSUMER Keep this manual with your Use & Care Guide for future reference. As when using any microwave oven generating heat, there are certain safety precautions you should follow. These are listed in the Use & Care Guide. Read all and follow carefully. Be sure your drawer microwave is installed and grounded properly by a qualified installer or service technician. Any questions or problems regarding the installation should be directed to your dealer or Wolf Appliance, Inc. at 800-332-9513. You can also visit our website, wolfappliance.com. CLEARANCES AND DIMENSIONS RATI NG P LATE I N F O R M AT I O N For safety considerations do not install drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 68. Model Number Serial Number RATING PLATE L OC ATION Record the model and serial numbers before installing the drawer microwave. Both numbers are listed on the product rating plate. Refer to the illustration below. The rating plate includes model and serial number. Open the drawer fully. The label is slightly beyond the back wall of the microwave cavity facing up from the flat surface. Rating plate: Open the drawer fully. The label is slightly beyond the back wall of the microwave cavity facing up from the flat surface. Rating plate location 3 W O L F DRAWER MICROWAVE I M P O RTA N T S A F E T Y I N S T R U C T I O N S If the information in this manual is not followed exactly, a fire or electrical shock may result that could cause property damage, personal injury or death. Never leave children alone or unattended in the area where a drawer microwave is in use. Never leave the drawer open when the microwave is unattended. To reduce the risk of tipping, the drawer microwave must be secured by a properly installed Anti-Tip block. This drawer microwave must be electrically grounded in accordance with local codes. Make sure the wall coverings and the cabinets around the drawer microwave can withstand the heat generated by the drawer microwave. Stepping, leaning or sitting on the drawer may result in serious injuries and can also cause damage to the drawer microwave. Do not use the drawer microwave as a storage space. This creates a potentially hazardous situation. Check that the time-of-day is in the display. If not, touch Stop/Clear to prevent unintended use. 4 I N S TA L L AT I O N I N S T R U C T I O N S U N PAC K I N G YO U R M I C R O WAV E CLEARANCES AND DIMENSIONS Remove all packing materials from inside the drawer microwave. Do not remove the waveguide cover, which is located on the top of the drawer microwave. Remove the feature sticker, if there is one. Check the drawer for any damage, such as misaligned or bent drawer, damaged drawer seals and sealing surfaces, broken or loose drawer guides and dents inside the cavity or on the front side of the drawer. If there is any damage, do not operate the drawer microwave and contact your dealer or a Wolf authorized service center. Refer to the illustrations below. Dimensions shown on the following pages must be used. Given dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See page 9. Contact surface must be solid and level. Pay special attention to the floor on which the drawer microwave will sit. The floor of the opening should be constructed of plywood strong enough to support the weight of the oven, about 100 pounds (45 kg). Check location where the drawer microwave will be installed for proper electrical supply. Your oven can be built into a cabinet or wall by itself or under a gas or electric wall oven. Be sure that the clearance of the floor between the wall oven and the drawer microwave is a minimum of 2" (51). The microwave interior will easily accommodate a 9" (229) x 13" (330) oblong dish or a bag of microwave popcorn. The trim will overlap cabinetry by 3/8" (10) at the top, 1/8" (3) at the bottom. The 24" (610) will overlap cabinetry by 1" (25) on each side. The 30" (762) will overlap cabinetry by 3/4" (19) on each side. Sealing surface Sealing surface Waveguide cover Oven cavity Waveguide cover location Sealing surface location Dimensions in parentheses are in millimeters unless otherwise specified. 5 W O L F DRAWER MICROWAVE 24" (610) D R AW E R MICROWAVE OVERALL DIMENSIONS 15 1/4" (387) 11/4" (32) POWER 13/4" CORD (44) CHANNEL 14 9/16" (370) 237/8" (606) 23 3/8" (594) BEHIND FRAME 219/16" (548) 411/16" (119) 23 3/8" (594) 161/2" (419) 237/8" (606) The drawer microwave can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 11/2" (38) diameter hole and deburred of all sharp edges. IMPORTANT NOTE: Always allow sufficient power cord length to the electrical outlet to prevent tension. Always check electrical codes for requirements. I N S TA L L AT I O N S P E CI F I C AT I ON S Standard Installation 31/2" (89) x 2" (51) ANTI-TIP BLOCK 143/4" (375) OPENING HEIGHT 231/2" min (597) OPENING DEPTH 24" min (610) CABINET DEPTH 2" (51) 36" (914) STANDARD FLOOR TO COUNTERTOP HEIGHT SIDE VIEW Dashed lines represent profile of unit. Flush Inset Installation 31/2" (89) x 2" (51) ANTI-TIP BLOCK 19/16" (38) 143/4" (375) OPENING HEIGHT 153/4" (400) FLUSH INSET HEIGHT 25" min (635) CABINET DEPTH 36" (914) STANDARD FLOOR TO COUNTERTOP HEIGHT SIDE VIEW Dashed line represents profile of unit. 6 27" rec (686) 24" min (610) CABINET WIDTH E 5/8" (16) PLATFORM 221/8" (562) OPENING WIDTH FRONT VIEW TOP VIEW 243/4" min (629) FLUSH INSET 11/4" DEPTH (32) SIDE CLEATS E 5/8" (16) TOP CLEAT 221/8" (562) OPENING WIDTH 3/8" (10) PLATFORM 24 3/8" (619) FLUSH INSET WIDTH 27" rec (686) 24" min (610) CABINET WIDTH 11/8" (29) SIDE CLEATS FRONT VIEW Dimensions in parentheses are in millimeters unless otherwise specified. I N S TA L L AT I O N I N S T R U C T I O N S 30" (762) D R AW E R MICROWAVE OVERALL DIMENSIONS 15 1/4" (387) 11/4" (32) POWER 2" CORD (51) CHANNEL 14 9/16" (370) 29 7/8" (759) 23 3/8" (594) BEHIND FRAME 281/8" (714) 411/16" (119) 23 3/8" (594) 29 7/8" (759) 161/2" (419) I NSTA LL ATIO N SPE CI F I C ATIO NS Standard Installation 31/2" (89) x 2" (51) ANTI-TIP BLOCK 33" rec (838) 30" min (762) CABINET WIDTH 143/4" (375) OPENING HEIGHT 231/2" min (597) OPENING DEPTH 24" min (610) CABINET DEPTH 2" (51) 36" (914) STANDARD FLOOR TO COUNTERTOP HEIGHT E 5/8" (16) PLATFORM 283/8" (721) OPENING WIDTH SIDE VIEW Dashed lines represent profile of unit. Flush Inset Installation 31/2" (89) x 2" (51) ANTI-TIP BLOCK 19/16" (38) 143/4" (375) OPENING HEIGHT 153/4" (400) FLUSH INSET HEIGHT 25" min (635) CABINET DEPTH 36" (914) STANDARD FLOOR TO COUNTERTOP HEIGHT SIDE VIEW Dashed line represents profile of unit. FRONT VIEW TOP VIEW 243/4" min (629) FLUSH INSET 11/4" DEPTH (32) E 5/8" (16) TOP CLEAT 283/8" (721) OPENING WIDTH 3/8" (10) PLATFORM 30 3/8" (772) FLUSH INSET WIDTH 36" rec (914) 33" min (838) CABINET WIDTH FRONT VIEW SIDE CLEATS 1" (25) SIDE CLEATS The drawer microwave can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 11/2" (38) diameter hole and deburred of all sharp edges. IMPORTANT NOTE: Always allow sufficient power cord length to the electrical outlet to prevent tension. Always check electrical codes for requirements. 7 W O L F DRAWER MICROWAVE 30" (762) D R AW E R MICROWAVE I N S TA L L AT I O N S P E CI F I C AT I ON S Installation below a Wolf E Series Built-In Oven TOP VIEW 11/4" (32) FOR DRAWER MICROWAVE 1" (25) FOR E SERIES OVEN 243/4" min (629) FLUSH INSET DEPTH The drawer microwave can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 11/2" (38) diameter hole and deburred of all sharp edges. IMPORTANT NOTE: Always allow sufficient power cord length to the electrical outlet to prevent tension. Always check electrical codes for requirements. SIDE VIEW 25" min (635) CABINET DEPTH 27 3/16" (691) OPENING HEIGHT 281/4" min (718) FLUSH INSET HEIGHT 143/4" (375) OPENING HEIGHT 151/2" (394) FLUSH INSET HEIGHT 36" rec (914) 33" min (838) CABINET WIDTH 7/8" (22) TOP CLEAT 281/2" (724) E SERIES OVEN OPENING WIDTH 19" (483) TO FLOOR (typical) 9/16" (14) PLATFORM* E 281/2" (724) DRAWER MICROWAVE OPENING WIDTH 3/8" (10) PLATFORM 30 3/8" min (772) FLUSH INSET WIDTH SIDE CLEATS 1" (25) SIDE CLEATS 1" (25) SIDE CLEATS SIDE VIEW FRONT VIEW *Platform must be able to support 250 lbs (113 kg). Refer to the 30" (762) E Series built-in oven specifications for electrical location. Dashed lines represent profile of unit. 8 I N S TA L L AT I O N I N S T R U C T I O N S ANTI-TIP BLOCK ELECTRICAL REQUIREMENTS I NSTA LL A NTI -TI P BL O CKING To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed located 1413/16" (376) above the floor on which the drawer microwave will sit. The 6" (152) Anti-Tip block must be provided by the installer. See pages 67. The Anti-Tip block prevents serious injury that might result from spilled hot liquids. If the drawer microwave is ever moved to a different location, the Anti-Tip block must also be moved and installed. When installed to the wall, make sure that the screws completely penetrate the dry wall and are secured in wood or metal so that the block is totally stable. When fastening, be sure that the screws do not penetrate electrical wiring or plumbing. ELECTRIC AL OUTLET LOC ATION The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp or more protected electrical supply. It is recommended that a separate circuit serving only this appliance be provided. The drawer is equipped with a 3-prong grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded. Should you only have a 2-prong outlet, have a qualified electrician install a correct wall receptacle. NOTE: If you have any questions about the grounding or electrical instructions, consult a qualified electrician or service person. I MPORTANT NOTE You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. 6" (153) Electrical Outlet Location Anti-tip Block 5" (127) 4" (102) Anti-tip block Electrical Outlet Dimensions in parentheses are in millimeters unless otherwise specified. 9 W O L F DRAWER MICROWAVE ELECTRICAL REQUIREMENTS DRAWER I N S TA L L AT I O N I MPO RTA NT NOTE You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. GROUNDING INSTRUCTIONS This appliance must be grounded. The drawer microwave is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current. Improper use of the grounding plug can result in a risk of electric shock. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance. 1) Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. 2) Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and the wall. 3) Slide the drawer all the way until the mounting flange is flush with the face of the cabinet. See illustration below. 4) Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16" (1.6) bit. See illustration below. 5) Secure the drawer with the 4 screws supplied. See illustration below. 3-Prong Plug Grounding Pin 3-Prong Receptacle Ground Receptacle Box Grounding 10 Drawer installation Mounting Flange 4 screws provided Dimensions in parentheses are in millimeters unless otherwise specified. I N S TA L L AT I O N I N S T R U C T I O N S I F YO U N E E D SERVICE Maintain the quality built into your drawer microwave by calling a Wolf authorized service center. To obtain the name and number of a Wolf authorized service center, check the Contact & Support section of our website, wolfappliance.com or call Wolf Customer Service at 800-332-9513. When calling for service, you will need the model and serial numbers of the drawer microwave. Both numbers are listed on the product rating plate. Refer to the illustration on page 3. CO NTACT I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance.com The information and images in this book are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. ©Wolf Appliance, Inc. all rights reserved. 11 W O L F A P P L I A N C E , I N C . P. O . B O X 4 4 8 4 8 M A D I S O N , W I 5 3 7 4 4 8 0 0 - 3 3 2 - 9 5 1 3 W O L FA P P L I A N C E . C O M 813533 REV-B TINSEB509MRR2 3/2009