Blaupunkt TWS1 BPE9W True Wireless Earpods Instruction Manual

Warnings

Read the below warnings thoroughly before you start using your earpods. Store this manual and warranty alongside with product packaging. The safety precaution instructions reduce the risk of fire, or injury when correctly complied to.

To reduce the risk of injury:

• Keep batteries out of reach of children.
• Do not heat, open, or dispose of battery pack in fire.
• Do not allow metal objects to touch the battery on the device.
• Do not expose battery pack to excessive heat.

Pairing

1. Auto Pairing

When taking out the Wireless Earpods from the charging case, the earphones will automatically turn on, sync together and enter pairing mode.

Note: When earphones sync successfully, only 1 earphone will flash blue/red indicating earphones have entered pairing mode.

Diagram Description: Two wireless earpods are shown being taken out of a charging case. The earpods are depicted as small, white, in-ear devices. The charging case is a rectangular box with a lid. Arrows indicate the earpods powering on and connecting to each other.

2. Syncing your Earpods

When EarPods do not sync together or become disconnected during use:

1. Turn off both earphones.
2. Continue to hold the "Right" EarPod button, and then press the "Left" EarPod button 3 times.
3. After that, stop holding the "Right" EarPod button and wait up to 10 seconds, both EarPods should sync automatically.
4. Finally, turn on Bluetooth on your phone to reconnect the EarPods.

Note: When EarPods successfully sync, only 1 earphone will flash blue/red indicating that it has entered pairing mode. If both EarPods Indicator lights flash blue/red, then pairing did not work. Please try sync again by following the above steps.

Diagram Description: The text describes a process involving pressing buttons on the earpods. The diagram implies the state where both earpods might flash blue/red if pairing fails.

3. Pairing Wireless Earpods to Smart Device

When you take your earpods out from charging case, your earpods will automatically enter pairing mode (blue/red light).

1. Open up Bluetooth settings on your smart device and scan for BPE9W.
2. Once you connect to your earpods, you can now listen to any audio from your smart device!

Note: If prompted for a password enter "1234" or "0000".

Diagram Description: A smartphone icon is shown with a Bluetooth symbol. The text describes connecting the earpods to the smart device via Bluetooth.

Button Function

1. On/Off Buttons

Press and hold the button on either earpod to turn them on or off.

2. Answer / Hang up

When there is an incoming call, press the button on the left or right earpod to answer the call. Press the button again to end the call.

Diagram Description: Two earpods are shown, each with a circular button. Arrows point to the buttons, indicating pressing them to answer or end a call.

3. Reject / Call Back

When there is an incoming call, press and hold the earpod button to refuse the call. Press the right earpod button 3 times to call back the last call.

Diagram Description: Two earpods are shown. Arrows indicate pressing and holding a button to reject a call, and pressing the right earpod button three times to call back the last number.

4. Voice Assistant

Press the LEFT earpod button 3 times to activate the voice assistant (Siri for iOS, Google Assistant for Android).

Diagram Description: A left earpod is shown with an arrow pointing to its button, indicating pressing it three times to activate a voice assistant (Siri or Google Assistant).

5. Play / Pause Music

When listening to music, press the earpod button to play or pause the music.

Diagram Description: An earpod is shown with an arrow pointing to its button, indicating pressing it to play or pause music.

6. Previous / Next Song

When listening to music:

• Previous: Press the left earpod button 2 times to go to the previous song.
• Next: Press the right earpod button 2 times to go to the next song.

Diagram Description: Two earpods are shown. Arrows indicate pressing the left earpod button twice for the previous song and the right earpod button twice for the next song.

Charging Function

1. Charging the Charging Case

There is a micro USB cable included in the packaging. Connect it to the "USB Charging Port" on the case and the other end into a USB powered source to charge your case.

Charging Case Indicator:

• Blue Light: Sufficient charging
• Flashing Blue Light: Battery is low
• No Light: Dead Battery

Diagram Description: A charging case is shown connected via a micro USB cable to a power source. An indicator light on the case is depicted.

2. Charging Earphones

Make sure to charge your charging case. Then place your earpods inside the charging case to charge them. While earpods are charging, the indicator light located on the earpods will turn RED.

Diagram Description: Two earpods are shown placed inside the charging case. An indicator light on each earpod is depicted as red, signifying charging.

Specifications

Included Items: True Wireless Earpods, Charging Case, Micro USB Cable, Instruction Manual, Spare Silicon earpads.

Customer Support

For assistance, please contact:

Email: info@ayonz.com

Distributed by: Ayonz Pty Ltd