tendacn.com
Installation Guide for Tenda models including: IC7-LRS-4V1.0 Conch Security Camera IC Series, IC7-LRS-4V1.0, Conch Security Camera IC Series, Security Camera IC Series, Camera IC Series, IC Series
Anchor: Height 6.6 mm, inner diameter 2.4 mm, length 26.4 mm Screw: BM3.0*5 mm (Head diameter: 6.0 mm) Camera×1 Installation template×1 Quick installation guide×1 Installation package x 1
File Info : application/pdf, 9 Pages, 705.15KB
DocumentDocumentQuick Installation Guide 4MP Conch Security Camera IC Series Please read this guide before you start with the quick setup for this camera upon the first use. For product or function details, please go to www.tendacn.com to download the user guide. IC7-LRS-4 is used for illustrations here unless otherwise specified. The actual product prevails. Package contents Camera×1 Installation template×1 Quick Installation Guide 4MP Conch Security Camera IC Series Please read this guide before you start with the quick setup for this camera upon the first use. For product or function details, please go to www.tendacn.com to download the user guide. IC7-LRS-4 is used for illustrations here unless otherwise specified. The actual product prevails. Quick installation guide×1 Appearance Installation package x 1 Anchor: Height 6.6 mm, inner diameter 2.4 mm, length 26.4 mm Screw: BM3.0*5 mm (Head diameter: 6.0 mm) Power jack Use the power adapter to power on the camera. Power-related parameters can be found on the label attached to the device. When the arrow is at 12 o'clock position, the monitoring direction is the positive direction. Microphone - 1 - Ethernet port, 10/100 Mbps auto-negotiation -If the camera supports the IEEE 802.3af standard, this port can be connected to the PoE port of a PoE power sourcing equipment for power supply. -If the camera does not support standard PoE, this port can be connected to routers, switches, etc. Install the device Remove the base Rotate the body of the camera, align the housing slot with any base notch, and then use a screwdriver to pry the housing at the slot to remove the base. Base notch Housing slot Install the camera The camera supports ceiling and wall installation. The ceiling installation is taken as an example here. Tips - Please make sure the ceiling is strong enough to withstand three times the weight of the camera. - You may need to prepare a hammer drill, a drill bit, a rubber hammer, a screwdriver, and a ladder for the installation. Installation template Anchor - 2 - A. Run the cable through the side Base Screw B. Run the cable through the bottom Base Screw Adjust the monitoring direction - 3 - Manage the device through Network Video Recorder(NVR) The series of cameras needs to be used with the NVR. You should add cameras on the NVR's web UI. For details, please refer to the user manual of the corresponding NVR. The series of cameras includes ordinary cameras and PoE cameras. Please connect the cable according to the actual conditions. Tips - The camera supports DC power supply (Power-related parameters can be found on the label attached to the device). The power adapter is not included in the package, so you need to purchase a power adapter that meets the requirements (port specification: 5.5*2.1 mm). - The PoE camera supports the IEEE 802.3af standard. Ordinary camera topology Internet Router WAN LAN Switch 1 2 3 4 5 Uppolinrtk Power outlet NVR POWER LAN LAN VGA USB Monitor Camera Camera Camera - 4- 5- - PoE camera topology Working with ordinary NVR Internet Router WAN LAN PoE Switch 1 2 3 4 5 Uppolinrtk NVR LAN Monitor PoE Camera PoE Camera PoE Camera Working with PoE NVR Internet Router LAN WAN LAN PoE Monitor PoE Camera PoE Camera - 6 - PoE Camera Log in to web UI You can log in to the web UI of the camera through a browser. 1. Connect the computer to the switch or router that is connected to the camera. 2. Set the IP address of the computer to an unused one belonging to the same network segment of the IP address of the camera but different from the IP address of the camera. The default login IP address of the camera is 192.168.1.203, and the Automatically Obtain IP address function is enabled. If there is a DHCP server in the network, the IP address of the camera may be changed. Please refer to the actual IP address assigned to the camera by the DHCP server. Internet Protocol Version 4 (TCP/IPv4) Properties General You can get IP settings assigned automatically if your network supports this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. Obtain an IP address automatically Use the following IP address: IP address: Subnet mask: Default gateway: 192 . 168 . 1 . 10 255 . 255 . 255 . 0 Obtain DNS server address automatically Use the following DNS server address: Preferred DNS server: Alternate DNS server: Validate settings upon exit Advanced... OK Cancel 3. Start a browser and enter the IP address of the camera in the address bar to access the login page. Enter the User Name (default: admin) and Password (default: admin123456), then click Login. English User Name Password Remember me Login After successfully logging in to the web UI of the camera, you can start to configure the camera as required. Tips For network security, after logging in to the web UI, please modify your username and password in time. If your camera has been successfully managed by the NVR, modifying the login username or password may cause the camera going offline. Please operate with caution. - 7 - CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. The mains plug is used as disconnect device, the disconnect device shall remain readily operable. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment. Temperature: -20°C-60°C Humidity: (10 - 95) %RH, non-condensing Technical Support Shenzhen Tenda Technology Co., Ltd. 6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 USA hotline: 1-800-570-5892 Toll Free: 7 x 24 hours Canada hotline: 1-888-998-8966 Toll Free: Mon - Fri 9 am - 6 pm PST Hong Kong hotline: 00852-81931998 Global hotline: +86 755-2765 7180 (China Time Zone) Website: www.tendacn.com E-mail: support@tenda.com.cn Copyright © 2021 Shenzhen Tenda Technology Co., Ltd. All rights reserved. Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice.