User Manual for NOVO models including: MD31028, 2AZMHMD31028, H12022 Transmitter, H12022, Transmitter
NOVO (GUANGDONG) HIGH-TECH CO., LTD. MD31028 Transmitter 2AZMHMD31028 2AZMHMD31028 md31028
Transmitter Operating Manual Company reserves the right to change product design and specifications without prior notice then photos are for reference only. B Button function and battery install specification Display channel 9 or 99 (P represents group control) Channel Key Up Key Stop Key Down Key Match code keyCODE CODE Programme keySET SET H12022 A/3 Install the back cover with force's direction Open the back cover with force's direction Front Contrary 1.5V dry cell seven×2 Open the back cover I Instructions ( *Take A3 button transmitter as an exampleFor other transmittersplease refer to the corresponding transmitter manual) Repeat the pairing operation once to eliminate the current pairingA motor stores up to 10 transmitter Pairing transmitter and motor channelsAdding a new transmitter channel will cover the earliest channelFor example, current paired channels are 1~10If you add channel 11paired channels will be 2~11 Tool with 3 mm diameter or less Motor response: rotate back and forth once. CODE SET Motor response: rotate back and forth once. 1Select the channel that will be paired 2PressSetbutton on motor Clear pairing Clear all pairing on the motor Motor response: rotate back and forth twice. Motor response: rotate back and forth once. 3Within 10s after motor stops, press Code button Speed se t t i n g Two speed can be Default is first adjusted Motor response: rotate back and forth three times. 1Press & HoldSet button on motor about 10s 2PressSetbutton on motor again Lock channel: factory default is the maximum channel Tool with 3 mm diameter or less Display the maximum CODE SET channel and flicker 1Press & HoldSetbutton on motor about 15s 1Keep press transmitter Setkey about 10s 2With in 6s, press Select-button to choose channel you want to lock 3Press theStop key to save the currently locked channel 4Display channel P Inching / Continuous moving interchange Default is continuous moving. After switching to inching button about 2s, motor will continuously moves moving, press & holdUporDown Tool with 3 mm diameter or less Motor response: CODE SET rotate back and forth once. Motor response: rotate back and forth once. 1Select the channel that will be interchanged 2Press & HoldSetbutton on transmitter about 10s 3Within 10s after motor stops, pressUpbutton about 5s Copy Add a new channel to control motor (No need to touch motor) Tool with 3 mm diameter or less Motor response: CODE rotate back and forth once. SET Tool with 3 mm diameter or less Motor response: CODE rotate back and forth once. SET A A transmitter A A transmitter B B transmitter 1Select the channel that will be copied 2Press & HoldCodebutton on 3Within 10s after motor stops, transmitter about 10s pair on the new channe Reset direction Reset motor directionSuch up buttonblinds run up as: before resetpress transmitter up buttonblinds run d ow nA f te r resetpress transmitter Tool with 3 mm diameter or less Motor response: CODE SET rotate back and forth once. Motor response: rotate back and forth once. 1Select the channel that will be reset direction 2Press & HoldSetbutton on transmitter about 10s 3Within 10s after motor stops, pressStopbutton about 5s Adjusting LimitsWhen you pressUporDownbuttonthe blinds will move up or down and stop automatically at the appointed position [Up] button Confirm direction Tool with 3 mm diameter or less Motor response: CODE rotate back and forth once. SET Motor response: rotate back and forth once. [Down] button If direction is not logical, please reset direction according "Reset direction"steps. Now you can start to adjust limits 1Press up button, blinds up. Press down button, blinds down Adjust up limit 2Select the channel that will be used to adjust limits 3Press & HoldSetbutton on 4Within 10s after motor stops, transmitter about 10s pressDownbutton about 5s Press stop button when blinds is near the appointed position. Motor response: rotate back Adjust down limit Confirm that blinds stops at the up limit position Save up limit 5Within 10s pressUp button to adjust up limit 6PressUp/Downbutton to 7Press & holdStop + Up move blinds, and then stop blinds about 1s to save up limit at the appointed position Press stop button when blinds is near the appointed position. Motor response: rotate back 8Within 10s pressDown button to adjust down limit Confirm that blinds stops at the down limit position Save down limit 9PressUp/Downbutton to move blinds, and then stop blinds at the appointed position 10Press & holdStop + Down about 1s to save down limit Adjust the third limit Repeat the operation once to eliminate the third limit Up limit position Press [up/down] button to move blinds, and then stop blinds at the appointed position. Third limit position Tool with 3 mm diameter or less. Motor response: CODE rotate back and forth SET once. Down limit position 1Select the channel that will be used to adjust limits 2Blinds moves to the third limit position 3Press & HoldSetbutton on transmitter about 10s Motor response: Rotate back and forth once. Motor response: Rotate back and forth once. Now you can start to adjust limits 4Within 10s after motor stops, pressDownbutton about 5s Successful to adjust the third limits 5Within 10s after motor stops, pressStopbutton about 5s Set the third limit between up and down limit, as the half ! position of blinds Reset up and down limit, or repeat third limit setting steps will eliminate the third limit Press & Hold [stop] button about 3s FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.Corel PDF Engine Version 14.0.0.701